- All Exams Instant Download
Where does an administrator configure the VLANs used in VRF Lite? (Choose two.)
Where does an administrator configure the VLANs used in VRF Lite? (Choose two.)A . uplink interface of the VRF gatewayB . uplink interface of the default Tier-0 gatewayC . uplink trunk segmentD . segment connected to the Tier-1 gatewayView AnswerAnswer: A, D Explanation: The VLANs used in VRF Lite are...
Which two CLI commands could be used to see if vmnic link status is down? (Choose two.)
Which two CLI commands could be used to see if vmnic link status is down? (Choose two.)A . esxcfg-nics -lB . esxcli network nic listC . esxcfg-vmknic -lD . esxcfg-vmsvc/get.networksE . esxcli network vswitch dvs vmware listView AnswerAnswer: A, B Explanation: esxcfg-nics -l: This command lists all physical NICs on...
Which failover detection protocol must be used to meet this requirement?
An NSX administrator wants to create a Tier-0 Gateway to support equal cost multi-path (ECMP) routing. Which failover detection protocol must be used to meet this requirement?A . Host Standby Router Protocol (HSRP)B . Beacon Probing (BP)C . Virtual Router Redundancy Protocol (VRRP)D . Bidirectional Forwarding Detection (BFD)View AnswerAnswer: D...
How does the Traceflow tool identify issues in a network?
How does the Traceflow tool identify issues in a network?A . Compares intended network state in the control plane with Tunnel End Point (TEP) keepalives in the data plane.B . Compares the management plane configuration states containing control plane traffic and error reporting from transport node agents.C . Injects ICMP...
What can the administrator use to identify overlay segments in an NSX environment if troubleshooting is required?
What can the administrator use to identify overlay segments in an NSX environment if troubleshooting is required?A . Geneve IDB . VMI IDC . Segment IDD . VLANIDView AnswerAnswer: B Explanation: In an NSX environment, each overlay segment is uniquely identified by a VNI ID (Virtual Network Identifier). The VNI...
Which is an advantage of an L2 VPN in an NSX 4.x environment?
Which is an advantage of an L2 VPN in an NSX 4.x environment?A . Achieve better performanceB . Use the same broadcast domainC . Enables Multi-Cloud solutionsD . Enables VM mobility with re-IPView AnswerAnswer: B Explanation: An L2 VPN (Layer 2 VPN) in an NSX 4.x environment allows you to...
What are two supported host switch modes? (Choose two.)
What are two supported host switch modes? (Choose two.)A . Overlay DatapathB . Secure DatapathC . Standard DatapathD . Enhanced DatapathE . DPDK DatapathView AnswerAnswer: C, D Explanation: Standard Datapath: This is the traditional mode used by the NSX host switch. It is typically used in environments where performance requirements...
Which VMware GUI tool is used to identify problems in a physical network?
Which VMware GUI tool is used to identify problems in a physical network?A . VMware Aria Operations NetworksB . VMware Aria AutomationC . VMware Site Recovery ManagerD . VMware Aria OrchestratorView AnswerAnswer: A Explanation: VMware Aria Operations Networks (formerly known as vRealize Network Insight) is a tool specifically designed for...
Which two are supported by L2 VPN clients? (Choose two.)
Which two are supported by L2 VPN clients? (Choose two.)A . NSX Autonomous EdgeB . NSX EdgeC . NSX for vSphere EdgeD . 3rd party Hardware VPN DeviceView AnswerAnswer: B, D Explanation: The NSX Edge supports L2 VPN (Layer 2 VPN) functionality, which allows it to connect different Layer 2...
Which two statements describe the characteristics of an Edge Cluster in NSX? (Choose two.)
Which two statements describe the characteristics of an Edge Cluster in NSX? (Choose two.)A . Must have only active-active edge nodesB . Can contain multiple types of edge nodes (VM or bare metal)C . Must contain only one type of edge nodes (VM or bare metal)D . Can have a...
