VMware 3V0-41.19 VMware Advanced Design NSX-T Data Center 2.4 Exam Online Training
VMware 3V0-41.19 Online Training
The questions for 3V0-41.19 were last updated at Nov 26,2024.
- Exam Code: 3V0-41.19
- Exam Name: VMware Advanced Design NSX-T Data Center 2.4 Exam
- Certification Provider: VMware
- Latest update: Nov 26,2024
An architect is helping an organization with the Logical Design of an NSX-T Data Center solution.
During discussions about Centralized Services NAT running on Tier-1 or Tier-0 LR the customer made these requests:
– Services contain stateful services.
– Services should be in high availability mode.
Which two should the architect include in their design? (Choose two.)
- A . An active/active model should be used.
- B . NAT should be applied on the uplink Interface.
- C . Mix stateful and stateless NAT rules on the same LR.
- D . The high availability mode supported is only Active-Stand by.
- E . Use only DNAT rules in stateful NAT.
An architect is helping an organization with the Physical Design of an NSX-T Data Center solution.
This information was gathered during the Assessment Phase:
– Deployment will be a brownfield vSphere environment.
– A smooth transition for deployment is required.
Which two should the architect include in their design? (Choose two.)
- A . Separate management and NSX Edge clusters.
- B . Set an end-to-end MTU of 9000.
- C . The physical gateway will be migrated to the Tier-1 gateway.
- D . The ESXi hosts will need at least one free physical NIC.
- E . L2 connectivity will be the core convergent network.
An architect is helping an organization with the Physical Design of an NSX-T Data Center solution.
This information was gathered during a workshop:
– There are six hosts and hardware has already been purchased.
– Customer is planning a collapsed Management/Edge/Compute cluster.
– Each host has two 10Gb NICs connected to a pair of ToR switches.
– There should be no single point of failure in any proposed design.
Which virtual switch design should the architect recommend to the organization?
- A . Create an NSX-T Virtual Distributed Switch (N-VDS) for Management VMkernal and overlay traffic and assign a new virtual NIC.
- B . Create an NSX-T Virtual Distributed Switch (N-VDS) for Management VMkernel and overlay traffic and assign both NICs.
- C . Create an NSX-T Virtual Distributed Switch (N-VDS) for Management VMkernel traffic and assign one NIC. Also, create an NSX-T Virtual Distributed Switch (N-VDS) for overlay traffic and assign one NIC.
- D . Create a vSphere Distributed Switch (vDS) for Management VMkernel traffic and assign one NIC. Also, create an NSX-T Virtual Distributed Switch (N-VDS) for overlay traffic and assign one NIC.
An architect is helping an organization with the Physical Design of an NSX-T Data Center solution.
This information was gathered during a workshop about ESXi Host networking:
– A total of 50 ESXI hosts to be configured as Transport Nodes.
– All ESXi hosts have a dedicated 2 x Intel 10Gbps Physical Network adapter for the Overlay Traffic.
To achieve low latency, high throughput, redundancy, and performance, which two NIC teaming policies should the architect recommend? (Choose two.)
- A . Load Balance Port ID
- B . Load Balance Source
- C . Load Balance Source Port ID
- D . Failover Order
- E . Load Balance Source MAC
A customer wants to place their NSX Managers in different subnets.
Which would an architect recommend to support the request?
- A . Use a cluster Virtual IP.
- B . Use round-robin DNS.
- C . Use a load balancer.
- D . Use NAT.
Latest 3V0-41.19 Dumps Valid Version with 50 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
