- All Exams Instant Download
Referring to the VCF shown in the exhibit, what is the remote destination trunk weight for the SW-4, SW-1, SW-5 path?
Referring to the VCF shown in the exhibit, what is the remote destination trunk weight for the SW-4, SW-1, SW-5 path? A . 10/40B . 30/40C . 20/40D . 40/40View AnswerAnswer: C
Referring to the exhibit, which two actions will solve this problem?
You are deploying a VXLAN using EVPN signaling overlay network. PE1 and PE2 are multihomed to the connected CE device. You notice that the traffic is not load-balancing as expected. Referring to the exhibit, which two actions will solve this problem? (Choose two.)A . Set the ESI on both devices...
Which event will cause R2 to establish the (S,G) state for VNI 5100 using R1 as the multicast source?
Referring to the exhibit, R1 and R2 are QFX5100s and are acting as VXLAN Layer 2 Gateways for VLAN 100 using PIM-SM signaling. R2 currently has only the (*.G) state established for VNI 5100. Which event will cause R2 to establish the (S,G) state for VNI 5100 using R1 as...
In this scenario, what must be corrected to solve the connectivity problem?
You have built a mixed-mode VCF consisting of two QFX5100-24Qs as spines, two QFX5100-48S as leaf nodes, and one EX4300 as a leaf node. The VCF is working for all devices, except the EX4300 40GbE fabric links will not join the VCF. In this scenario, what must be corrected to...
If a single spine device fails, what percentage of the remaining bandwidth will be available from leaf node to leaf node?
A customer has a 3-stage Clos architecture with three spine devices as shown in the exhibit. If a single spine device fails, what percentage of the remaining bandwidth will be available from leaf node to leaf node?A . approximately 25%B . approximately 33%C . approximately 75%D . approximately 66%View AnswerAnswer:...
Which two statements are correct in this scenario?
You are performing an in-service software upgrade (ISSU) on an QFX5100 Series device. Which two statements are correct in this scenario? (Choose two.)A . The vccpd process is used to synchronize the state of the master RE to the new backup RC . The mgd process is used to validate...
What will cause R2 to send a (*.G) PIM Join towards the RP?
Referring to the exhibit, R1 and R2 are QFX5100s and are acting as VXLAN Layer 2 Gateways for VLAN 100 using PIM-SM signaling. What will cause R2 to send a (*.G) PIM Join towards the RP? A. R2 will send a (*.G) PIM Join when it receives broadcast, multicast, or...
What are two reasons why MPLS would be used a transport for this DCI solution?
You are building a DCI solution and need both a Layer 2 solution and a Later 3 solution for different workloads within your data centers. What are two reasons why MPLS would be used a transport for this DCI solution? (Choose two.)A . The fast failover capabilities of MPLS nodes...
Which statement is valid for EVPN multihoming CE1 to PE1 and PE2 as shown in the exhibit?
Which statement is valid for EVPN multihoming CE1 to PE1 and PE2 as shown in the exhibit? A . CE1 must have LACP enabled on the interfaces attached to the PEs.B . The PEs must be manually configured for the ESI value on the interfaces attached to the CEs.C ....
Which statement is correct about the Edge1 device in this scenario?
Referring to the exhibit, PE1 and PE2 are acting as MPLS Layer 3 VPN PEs to provide the DCI between DC1 and DC2, which are IP Fabrics. Leaf1 and Leaf2 are QFX5100 Series devices acting as VXLAN Layer 2 Gateways using EVPN signaling for the same VXLAN segment. Which statement...
