- All Exams Instant Download
Given the partial BGP configuration, which configuration correctly completes the Cisco IOS-XR route reflector configuration where both the 1.1.1.1 and 2.2.2.2 routers are the clients and the 3.3.3.3 router is a non-client IBGP peer?
Refer to the exhibit. Given the partial BGP configuration, which configuration correctly completes the Cisco IOS-XR route reflector configuration where both the 1.1.1.1 and 2.2.2.2 routers are the clients and the 3.3.3.3 router is a non-client IBGP peer?A . neighbor 1.1.1.1 remote-as 65123 route-reflector-client neighbor 2.2.2.2 remote-as 65123 route-reflector-client neighbor...
Which three statements are correct regarding PIM-SM? (Choose three.)
Which three statements are correct regarding PIM-SM? (Choose three.)A . There are three ways to configure the RP: Static RP, Auto-RP, or BSRB . PIM-SM only uses the RP rooted shared tree and has no option to switch over to the shortest path treeC . Different RPs can be configured...
In Cisco IOS-XR, the maximum-prefix command, to control the number of prefixes that can be installed from a BGP neighbor, is configured under which configuration mode?
In Cisco IOS-XR, the maximum-prefix command, to control the number of prefixes that can be installed from a BGP neighbor, is configured under which configuration mode?A . RP/0/RSP0/CPU0:P2(config-bgp)#B . RP/0/RSP0/CPU0:P2(config-bgp-af)#C . RP/0/RSP0/CPU0:P2(config-bgp-nbr)#D . RP/0/RSP0/CPU0:P2(config-bgp-nbr-af)#View AnswerAnswer: D
Which additional configuration is required to pass the IPv6 traffic over the IPv4 network?
After configuring the tunnel interface as shown in the exhibit, no IPv6 traffic is passed over the IPv4 network. Which additional configuration is required to pass the IPv6 traffic over the IPv4 network?A . Configure an IPv4 address on the tunnel0 interfaceB . Configure an IPv6 static route to send the...
When implementing source-based remote-triggered black hole filtering, which two configurations are required on the edge routers that are not the signaling router? (Choose two.)
When implementing source-based remote-triggered black hole filtering, which two configurations are required on the edge routers that are not the signaling router? (Choose two.)A . A static route to a prefix that is not used in the network with a next hop set to the Null0 interfaceB . A static...
0.2.1/32 null0
0.2.1/32 null0 ! route-policy test if tag is 666 then set next-hop 192.0.2.1 set community (no-export) endif end-policy !View AnswerAnswer: C Explanation: Source-Based RTBH Filtering With destination-based black holing, all traffic to a specific destination is dropped after the black hole has beenactivated, regardless of where it is coming from....
Which multicast group range is reserved for SSM?
Which multicast group range is reserved for SSM?A . 224.0.0.0/8B . 225.0.0.0/8C . 232.0.0.0/8D . 239.0.0.0/8View AnswerAnswer: C Explanation: PIM-SSM Operations PIM in Source Specific Multicast operation uses information found on source addresses for a multicast group provided by receivers and performs source filtering on traffic. - By default, PIM-SSM...
On the PE, which two stateme s are correct regarding the (192.168.156.60 224.1.1.1) entry?
On the PE, which two stateme s are correct regarding the (192.168.156.60 224.1.1.1) entry? (Choose two )A . The RPF neighbor points towards the RPB . The RPF neighbor is reachable overthe GiO/O/O/1 interfaceC . The OIL contains the GiO/O/O/O interfaceD . The IIL is NullView AnswerAnswer: A C Explanation: #show ip mroute
Please Answer Questions Follow The Prompts Below
DRAG DROP View AnswerAnswer: Explanation: Any Source Multicast - Uses RP's as the root of the shared tree for a multicast group, ONly (S,G) state is build between the source and the recevier, Spport SPT SwitchoverSource Specific Multicast - Uses (*,G) joins as well as (S,G) Joins , Requires IGMPV3...
Cisco NSR be required?
When implementing high-availability stateful switchover BGP routing, in which situation would Cisco NSR be required?A . On the PE routers connecting to the CE routers which are not NSF aware or are not NSF capableB . On the PE routers connecting to the CE routers which support graceful restartC ....
