When the "setas" route map is applied to the 10.1.1.2 neighbor, the 10.1.1.2 neighbor is not able to receive all the required BGP routes from this router. What could be the problem?

Refer to the BGP and route map configurations exhibit. When the "setas" route map is applied to the 10.1.1.2 neighbor, the 10.1.1.2 neighbor is not able to receive all the required BGP routes from this router. What could be the problem?A . The BGP session was cleared using the clear...

March 4, 2019 No Comments READ MORE +

Which two statements about a transit AS are correct? (Choose two.)

Which two statements about a transit AS are correct? (Choose two.)A . A transit AS has eBGP connection(s) to only one external AC . Routes between ASs are always exchanged via eBGE . A transit AS uses an IGP like OSPF or ISIS to propagate the external networks within the...

March 2, 2019 No Comments READ MORE +

Which OSPF feature allows a router with redundant route processors to maintain its OSPF state and adjacencies across planned and unplanned RP switchovers and does this by checkpointing state information from OSPF on the active RP to the standby RP? This feature does not require the OSPF neighbor to support graceful restart.

Which OSPF feature allows a router with redundant route processors to maintain its OSPF state and adjacencies across planned and unplanned RP switchovers and does this by checkpointing state information from OSPF on the active RP to the standby RP? This feature does not require the OSPF neighbor to support...

March 1, 2019 No Comments READ MORE +

What are three common problems that can cause a BGP neighbor state to toggle between the idle state and the active state? (Choose three.)

What are three common problems that can cause a BGP neighbor state to toggle between the idle state and the active state? (Choose three.)A . BGP network command misconfigurationB . route policy misconfigurationC . AS number misconfigurationD . route map misconfigurationE . BGP neighbor peering to wrong IP addressF ....

February 28, 2019 No Comments READ MORE +

Which of the following is used by an IS-IS router to detect other IS-IS neighbor routers and to form adjacencies?

Which of the following is used by an IS-IS router to detect other IS-IS neighbor routers and to form adjacencies?A . ESHB . ISHC . IIHD . PSNPE . CSNPView AnswerAnswer: C

February 28, 2019 No Comments READ MORE +

Which three BGP configuration groupings are supported on Cisco IOS XR Software? (Choose three.)

Which three BGP configuration groupings are supported on Cisco IOS XR Software? (Choose three.)A . peer-groupB . af-groupC . bgp-groupD . session-groupE . neighbor-groupF . as-groupView AnswerAnswer: B,D,E

February 27, 2019 No Comments READ MORE +

Which reserved AS number or range of numbers is used for backward compatibility between old BGP peers using 16-bit AS number and new BGP peers using 32-bit AS number?

Which reserved AS number or range of numbers is used for backward compatibility between old BGP peers using 16-bit AS number and new BGP peers using 32-bit AS number?A . AS 65001 to 65535B . AS 65512 to 65535C . AS 12345D . AS 23456E . AS 64001View AnswerAnswer: D

February 27, 2019 No Comments READ MORE +

Assuming the IBGP session within AS 64500 was established using the loopback 0 interface between the two routers, by default, what will be the next hop of the routes from AS 64501 when the routes appear on the router running IBGP only in AS 64500?

Refer to the network diagram in the exhibit. Assuming the IBGP session within AS 64500 was established using the loopback 0 interface between the two routers, by default, what will be the next hop of the routes from AS 64501 when the routes appear on the router running IBGP only...

February 27, 2019 No Comments READ MORE +

When using the Cisco IOS XR route policy language to define a logical if-then-else condition, which logical operator has the highest precedence?

When using the Cisco IOS XR route policy language to define a logical if-then-else condition, which logical operator has the highest precedence?A . ANDB . ORC . NOTD . ISE . INView AnswerAnswer: C

February 26, 2019 No Comments READ MORE +

Assuming the IBGP session within AS 64500 was established using the loopback 0 interface between the two routers, by default, what will be the next hop of the routes from AS 64501 when the routes appear on the router running IBGP only in AS 64500?

Refer to the network diagram in the exhibit. Assuming the IBGP session within AS 64500 was established using the loopback 0 interface between the two routers, by default, what will be the next hop of the routes from AS 64501 when the routes appear on the router running IBGP only...

February 26, 2019 No Comments READ MORE +