Which description of this behavior is true?

In a L2VPN service, customer CE sends frames to PE1 using a CoS making value of 3. However, the remote CE receives those frames from PE2 with a CoS marking value of 0. Which description of this behavior is true?A . Egress PE2 is not configured with an outbound policy-map...

December 21, 2018 No Comments READ MORE +

What type of IPv6 address is the address FF05::2:260:8F908?

What type of IPv6 address is the address FF05::2:260:8F908?A . Multicast temporary site localB . Multicast permanent node link localC . Multicast permanent site localD . Multicast permanent link localView AnswerAnswer: C

December 21, 2018 No Comments READ MORE +

Which three OSPF pieces of information must between routers in order to establish an ospf neighborship? (Choose three)

Which three OSPF pieces of information must between routers in order to establish an ospf neighborship? (Choose three)A . Area IDB . Hello interval and dead interval timer valueC . LSA refresh period timer valueD . Priority valueE . Stub flagF . Process IDView AnswerAnswer: A, B, E

December 20, 2018 No Comments READ MORE +

Which BGP configuration must be applied to make PE3 use both BGP entries in the Cisco Express Forwarding table?

Refer to the exhibit. Which BGP configuration must be applied to make PE3 use both BGP entries in the Cisco Express Forwarding table?A . On PE1, apply nexto-hop-self on both PE2 and PE3 neighbors configurationB . On the CE, apply bgp add-path on both PE1 and PE2 neighbors configurationC ....

December 19, 2018 No Comments READ MORE +

Which routing table is used by PEs and ASBRs to store all VPN routes that need to be exchanged in an Inter-AS L3VPN option B scenario?

Which routing table is used by PEs and ASBRs to store all VPN routes that need to be exchanged in an Inter-AS L3VPN option B scenario?A . IGP tableB . VRF routing tableC . Global routing tableD . BGP tableView AnswerAnswer: D

December 18, 2018 No Comments READ MORE +

Which action is required to bring the MPLS TE tunnel 0 to up state?

Refer to the exhibit. A service provider is running MPLS TE across its network. IS-IS is deployed as the IGP for the ISP network. The MPLS TE tunnel 0 configured on PE2 is seen in an operational down state. PE2 is a level-1 router and the destination 192.168.1.1 is located...

December 18, 2018 No Comments READ MORE +

To allow the CE to install these routes which command should be implemented?

A service provider is managing a CE that is used to segment multiple customers into dedicate VRFs. OSPF is used as the PE-CE routing protocol the managed CE does not have the customers routes in its RIB. To allow the CE to install these routes which command should be implemented?A...

December 16, 2018 No Comments READ MORE +

Which BGP feature improves the convergence and response time to adjacency changes with BGP neighbors?

Which BGP feature improves the convergence and response time to adjacency changes with BGP neighbors?A . reducing BGP scanner timing to the minimum that is supportedB . BGP MultihopC . Next-Hop Address TrackingD . Fast Peering Session DeactivationE . TTL Security CheckView AnswerAnswer: E

December 15, 2018 No Comments READ MORE +

Which two statements are correct in regards to MSDP SA messages received by R5 located in AS 7?

Refer to the exhibit. All links have same bandwidth configured AS 4, AS 4 and AS 7 run OSPF as IGP using default metric values. Which two statements are correct in regards to MSDP SA messages received by R5 located in AS 7? (Choose two)A . All MSDP SA messages...

December 14, 2018 No Comments READ MORE +

A service provider is using point-to-multipoint TE to forward MPLS traffic from one source to multiple destinations, what is a restriction of using this method?

A service provider is using point-to-multipoint TE to forward MPLS traffic from one source to multiple destinations, what is a restriction of using this method?A . Destinations must be manually added and removed on the TE tail-end routerB . Multicast traffic must be implemented using PIM sparse modeC . Point-to-multipoint...

December 12, 2018 No Comments READ MORE +