Which two commands should be configured to meet these requirements?

An engineer is implementing OTV on a transport that supports multicast. The solution needs to meet the following requirements: • Establish adjacency to the remote peer by using multicast. • Enable OTV advertisements for VLAN 100 to the other site. Which two commands should be configured to meet these requirements?...

December 10, 2021 No Comments READ MORE +

Which set of commands must be used to meet these requirements?

A Cisco MDS 9000 Series Switch is configured for SAN Analytics and SAN Telemetry Streaming. An engineer must enable analytics for NVMe on interfaces in the range of fc1/1-12. Due to a large amount of traffic generated in the SAN environment, the data must be collected at regular intervals of...

December 10, 2021 No Comments READ MORE +

Which type of IP address is used by the Cisco Fabric Services protocol?

Refer to the exhibit. Cisco Fabric Services is enabled in the network . Which type of IP address is used by the Cisco Fabric Services protocol?A . IPv4 unicast addressB . IPv4 multicast addressC . IPv4 gateway addressD . IPv4 anycast addressView AnswerAnswer: B Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/configuration/guide/fm/FabricManager/cfs.pdf

December 10, 2021 No Comments READ MORE +

Which statement is true about the Deployment Immediacy for VMM domains associated to EPGs?

APIC EPG Resolution Immediacy is set to “Immediate”. Which statement is true about the Deployment Immediacy for VMM domains associated to EPGs?A . The “Immediate” and “On demand” options require a port group to be created on the VDC . If “On demand” is selected, the policy is programmed in...

December 10, 2021 No Comments READ MORE +

Which Information must be included In the comma-separated value flit to provision the targets?

An engineer configures an intersignt virtual application and must claim over 200 targets. The engineer starts the Claim target procedure. The engineer has prepared this initial comma- separated value file to provision the targets: Which Information must be included In the comma-separated value flit to provision the targets?A . FQON,...

December 10, 2021 No Comments READ MORE +

Which behavior defines streaming telemetry as a push model in Cisco devices?

Which behavior defines streaming telemetry as a push model in Cisco devices?A . Monitoring clients are pulling data from the network to see real-time statisticsB . JSON encoded telemetry data is transported using the gRPC protocolC . The network devices send data in JSON or GPB format to configured endpointsD...

December 10, 2021 No Comments READ MORE +

Which feature needs to be used?

An administrator needs to configure an automated policy to shut down a link when a given threshold is exceeded on MDS switch . Which feature needs to be used?A . SchedulerB . RMONC . EEMD . Call HomeView AnswerAnswer: C Explanation: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/6_2/configuration/guides/interfaces/nx-os/cli_interfaces/intf.html

December 10, 2021 No Comments READ MORE +

Which two policies must be configured to meet these requirements?

An engineer creates a service profile in Cisco UCS Manager and must assign a policy that reboots blades when changes are applied. The changes must be applied only after user acknowledgment . Which two policies must be configured to meet these requirements? (Choose two.)A . Boot PolicyB . Global PolicyC...

December 10, 2021 No Comments READ MORE +

Which two commands should be configured to meet these requirements?

An engineer is implementing OTV on a transport that supports multicast. The solution needs to meet the following requirements: • Establish adjacency to the remote peer by using multicast. • Enable OTV advertisements for VLAN 100 to the other site. Which two commands should be configured to meet these requirements?...

December 9, 2021 No Comments READ MORE +

What setting will accomplish this goal?

An engineer is seeking the most optimal on demand CPU performance while configuring the BIOS settings of a UCS C-series rack mount server. What setting will accomplish this goal?A . C0/C1 stateB . C6 RetentionC . C2 stateD . C6 non-RetentionView AnswerAnswer: B Explanation: Reference: https://www.cisco.com/c/en/us/products/collateral/servers-unified-computing/ucs-b-series-blade-servers/white-paper-c11-744678.html. For Package C State...

December 9, 2021 No Comments READ MORE +