- All Exams Instant Download
Which two configurations must be implemented to meet the requirements?
Refer to the exhibit. A network engineer must meet these requirements to provide a connects, solution: ✑ The customer connected to Area 2 needs to access the application in Area 1 on the 10.10.10.0/24 subnet ✑ The Customer must not have access to the 20.10 30.0/24 subnet. ✑ The service...
Which condition must be met by the OSPF peer of router R1 before the two devices can establish communication?
Refer to the exhibit: Which condition must be met by the OSPF peer of router R1 before the two devices can establish communication?A . The interface on the OSPF peer must use the same key ID and key value as the configured interfaceB . The interface on the OSPF peer...
Why do packet loops occur during the configuration of BlDlR-PIM?
Why do packet loops occur during the configuration of BlDlR-PIM?A . The network does not support BIDIR-PIMB . The network is partially upgraded to support BIDlR-PIMC . No interface for carrying traffic for multicast groups has been configuredD . The router has not been configured to advertise itselfView AnswerAnswer: B
Which configuration must the engineer apply to the router?
Refer to the exhibit. An engineer is implementing BGP selective prefix suppression. The router must advertise only 10.16.4.0/24,10.16.5.0/24. and summarized route 10.16.0.0/21. and suppress 10.16.6.0/24. Which configuration must the engineer apply to the router? A) B) C) D) A . Option AB . Option BC . Option CD . Option...
Which statement about this configuration is true?
Refer to the exhibit: This configuration is being applied on an IOS XR router. Which statement about this configuration is true?A . It is used to create a subscription to specify the streaming intervalB . It is used to identify traps for SNMP pollingC . It is used to identify...
Which task completes the configuration?
Refer to the exhibit. Which task completes the configuration?A . Specify the maximum number of prefixes that R1 receives from neighbor 192.168.1.2.B . Specify the source interface in the neighbor statement.C . Specify the activate neighbor 192.168.1.2 under the IPv4 address family.D . Specify the local-as value in the neighbor...
Which configuration must an engineer apply to resolve this problem?
Refer to the exhibit. Router BRDR-1 is configured to receive the 0.0.0.0/0 and 172.17.1.0/24 network via BGP and advertise then into OSPF area 0. An engineer has noticed that the OSPF domain is receiving only the 172.17.1.0/24 route and default router 0.0.0.0/0 is still missing. Which configuration must an engineer...
Drag and drop the NAT64 descriptions from the left onto the correct NAT64 types on the right
DRAG DROP Drag and drop the NAT64 descriptions from the left onto the correct NAT64 types on the right. View AnswerAnswer: Explanation: Stateful (It has 1: N translation, It uses address overloading, It conservers IPv4 addresses) Stateless (It is limited on the number of endpoints, It mandates IPv4-translatable IPv6 address...
What is a constraint of Cisco MPLS TE tunnel configurations?
What is a constraint of Cisco MPLS TE tunnel configurations?A . Tunnels cannot span multiple OSPF areas.B . With ISIS as an IGC . only older-style metrics are used.D . Tunnels cannot be configured over IP unnumbered links.E . QoS-aware tunneling is not supported.View AnswerAnswer: C
R1 message periodically Based on this output, which statement is true?
Refer to the exhibits: R1 and R2 are directly connected and IS-IS routing has been enabled between R1 and R2 R1 message periodically Based on this output, which statement is true?A . IS-IS neighbor authentication is failing for Level 2 first and then for Level 1 PDUsB . 1S-1S neighbor...
