- All Exams Instant Download
Which command set must be applied to the NewYork switch to resolve the issue?
Refer to the Exhibit. Communication between London and New York is down. Which command set must be applied to the NewYork switch to resolve the issue?A . NewYork(config)#no interface po1 NewYork(config)#interface range fa0/1-2 NewYork(config-if)#channel-group 1 mode negotiate NewYork(config-if)#end NewYork#B . NewYork(config)#no interface po1 NewYork(config)#interface range fa0/1-2 NewYork(config-if)#channel-group 1 mode on...
Which command configures the router to be the destination of jitter measurements?
An engineer is concerned with the deployment of new application that is sensitive to inter-packet delay variance. Which command configures the router to be the destination of jitter measurements?A . Router(config)# ip sla responder udp-connect 172.29.139.134 5000B . Router(config)# ip sla responder tcp-connect 172.29.139.134 5000C . Router(config)# ip sla responder...
Which characteristic distinguishes Ansible from Chef?
Which characteristic distinguishes Ansible from Chef?A . Ansible lacs redundancy support for the master server. Chef runs two masters in an active/active mode.B . Ansible uses Ruby to manage configurations. Chef uses YAML to manage configurations.C . Ansible pushes the configuration to the client. Chef client pulls the configuration from...
What does the output confirm?
Refer to the Exhibit. A network engineer configures NAT on R1 and enters the show command to verity the configuration. What does the output confirm?A . The first pocket triggered NAT to add on entry to NAT tableB . R1 is configured with NAT overload parametersC . A Telnet from...
Which command set is required?
An engineer must configure HSRP group 300 on a Cisco IOS router. When the router is functional, it must be the must be the active HSRP router. The peer router has been configured using the default priority value. Which command set is required?A . standby 300 priority 110 standby 300...
Which configuration commands can the engineer use to allow this traffic without disrupting existing traffic flows?
Refer to the exhibit. An engineer must modify the access control list EGRESS to allow all IP traffic from subnet 10.1.10.0/24 to 10.1.2.0/24. The access control list is applied in the outbound direction on router interface GigabitEthemet 0/1. Which configuration commands can the engineer use to allow this traffic without...
Which configuration change will force BR2 to reach 209 165 201 0/27 via BR1?
Refer to the Exhibit. Which configuration change will force BR2 to reach 209 165 201 0/27 via BR1?A . Set the weight attribute to 65.535 on BR1 toward PE1.B . Set the local preference to 150 on PE1 toward BR1 outboundC . Set the MED to 1 on PE2 toward...
What are two effects of this configuration?
Refer to the exhibit. What are two effects of this configuration? (Choose two.)A . R1 becomes the active router.B . R1 becomes the standby router.C . If R2 goes down, R1 becomes active but reverts to standby when R2 comes back online.D . If R1 goes down. R2 becomes active...
Which method can a client use to authenticate to the network?
Refer to the exhibit. Based on the configuration in this WLAN security setting. Which method can a client use to authenticate to the network?A . text stringB . username and passwordC . certificateD . RADIUS tokenView AnswerAnswer: A
When two actions from the initial value of the TTL?
Refer to the exhibit. Which troubleshooting a routing issue, an engineer issues a ping from S1 to S2. When two actions from the initial value of the TTL? (Choose two.)A . The packet reaches R3, and the TTL expiresB . R2 replies with a TTL exceeded messageC . R3 replies...
