Drag and drop the MPLS terms from the left onto the correct definitions on the right

DRAG DROP Drag and drop the MPLS terms from the left onto the correct definitions on the right. View AnswerAnswer:

September 16, 2022 No Comments READ MORE +

Which command fixes the issue?

Refer to the exhibit. An IP SLA is configured to use the backup default route when the primary is down, but it is not working as desired. Which command fixes the issue?A . R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2 10 track 1 B. R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2 C. R1(config)#ip sla track 1...

September 16, 2022 No Comments READ MORE +

Refer to the exhibit

DRAG DROP Refer to the exhibit. Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed View AnswerAnswer: Explanation: vty 0: + cisco + 0csic...

July 26, 2022 No Comments READ MORE +

What are the two solutions to fix the issue?

Exhibit: BGP is flapping after the Copp policy is applied. What are the two solutions to fix the issue? (Choose two)A . Configure BGP in the COPP-CRITICAL-7600 ACLB . Configure a higher value for CIR under the default class to allow more packets during peak trafficC . Configure a higher...

July 25, 2022 No Comments READ MORE +

Which method changes the forwarding decision that a router makes without first changing the routing table or influencing the IP data plane?

Which method changes the forwarding decision that a router makes without first changing the routing table or influencing the IP data plane?A . nonbroadcast multiaccessB . packet switchingC . policy-based routingD . forwarding information baseView AnswerAnswer: C

July 25, 2022 No Comments READ MORE +

Which command must the engineer run to correct the configuration?

An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install. Which command must the engineer run to correct the configuration?A . sudo maglev-config updateB . sudo maglev install config updateC . sudo maglev reinstallD . sudo update config installView AnswerAnswer: A

July 25, 2022 No Comments READ MORE +

Which list defines the contents of an MPLS label?

Which list defines the contents of an MPLS label?A . 20-bit label; 3-bit traffic class; 1-bit bottom stack; 8-bit TTLB . 32-bit label; 3-bit traffic class; 1-bit bottom stack; 8-bit TTLC . 20-bit label; 3-bit flow label; 1-bit bottom stack; 8-bit hop limitD . 32-bit label; 3-bit flow label; 1-bit...

July 25, 2022 No Comments READ MORE +

Why is the summary route missing?

Refer to the exhibit. An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table. Why is the summary route missing?A . The summary-address command is used only for summarizing prefixes between areas.B . The...

July 25, 2022 No Comments READ MORE +

Which debug command is used to troubleshoot this issue?

Refer to the exhibit. An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through router R2. Which debug command is used to troubleshoot this...

July 25, 2022 No Comments READ MORE +

In which circumstance does the BGP neighbor remain in the idle condition?

Refer to the exhibit. In which circumstance does the BGP neighbor remain in the idle condition?A . if prefixes are not received from the BGP peerB . if prefixes reach the maximum limitC . if a prefix list is applied on the inbound directionD . if prefixes exceed the maximum...

July 24, 2022 No Comments READ MORE +