- All Exams Instant Download
Which two issues will prevent this setup from working properly?
Users were moved from the local DHCP server to the remote corporate DHCP server. After the move, none of the users were able to use the network. Which two issues will prevent this setup from working properly? (Choose two)A . Auto-QoS is blocking DHCP traffic.B . The DHCP server IP...
Drag and drop the packet types from the left onto the correct descriptions on the right
DRAG DROP Drag and drop the packet types from the left onto the correct descriptions on the right. View AnswerAnswer: Explanation: Unlike legacy network technologies such as ISDN, Frame Relay, and ATM that defined separate data and control channels, IP carries all packets within a single pipe. Thus, IP network...
What is an advantage of using BFD?
What is an advantage of using BFD?A . It detects local link failure at layer 1 and updates routing table.B . It detects local link failure at layer 2 and updates routing protocols.C . It has sub-second failure detection for layer 1 and layer 3 problems.D . It has sub-second...
Which component of MPLS VPNs is used to extend the IP address so that an engineer is able to identify to which VPN it belongs?
Which component of MPLS VPNs is used to extend the IP address so that an engineer is able to identify to which VPN it belongs?A . VPNv4 address familyB . RDC . RTD . LDPView AnswerAnswer: B Explanation:
Which statement about MPLS LDP router ID is true?
Which statement about MPLS LDP router ID is true?A . If not configured, the operational physical interface is chosen as the router ID even if a loopback is configured.B . The loopback with the highest IP address is selected as the router ID.C . The MPLS LDP router ID must...
What is the reason for this?
Refer to the exhibit. An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?A . Dynamic routing protocols always have priority over static routes.B . The metric of the...
Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?
Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?A . multi-paths eibgp 2B . maximum-paths 2C . Maximum-paths ibgp 2D . multi-paths 2View AnswerAnswer: C Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/5_x/nx-os/mpls/configuration/guide/mpls_cg/mp_vpn_multipath.html
Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right
DRAG DROP Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right. View AnswerAnswer: Explanation: (Reference: http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080093f0e.sh tml) Reference: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13685-13.html Down This is the first OSPF neighbor state. It means that no information (hellos) has been received from this neighbor, but hello packets...
Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right
DRAG DROP Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right. View AnswerAnswer: Explanation: HTTP and HTTPs run on TCP port 80 and 443, respectively and we have to remember them. Syslog runs on UDP port 514 while NTP runs on UDP...
Which command must be configured first to troubleshoot this issue?
While troubleshooting connectivity issues to a router, these details are noticed: ✑ Standard pings to all router interfaces, including loopbacks, are successful. ✑ Data traffic is unaffected. ✑ SNMP connectivity is intermittent. ✑ SSH is either slow or disconnects frequently. Which command must be configured first to troubleshoot this issue?A...
