- All Exams Instant Download
The following debug messages are noticed for HSRP group 2. But still neither R1 nor R2 has identified one of them as standby router. Identify the reason causing the issue.
The following debug messages are noticed for HSRP group 2. But still neither R1 nor R2 has identified one of them as standby router. Identify the reason causing the issue. Note: only show commands can be used to troubleshoot the ticket. R1# 'Mar 26 11:17:39.234: HSRP: Et1/0 Grp 2 Hello...
What should be the next step after the problem is solved?
What should be the next step after the problem is solved?A . document itB . knowledge transferC . result analysisView AnswerAnswer: A Explanation: Cisco has broken this process into eight steps:
What should be the next step after the problem is solved?
What should be the next step after the problem is solved?A . document itB . knowledge transferC . result analysisView AnswerAnswer: A Explanation: Cisco has broken this process into eight steps:
You have been asked by your customer to help resolve issues in their routed network. Their network engineer has deployed HSRP. On closer inspection HSRP doesn't appear to be operating properly and it appears there are other network problems as well. You are to provide solutions to all the network problems
HSRP Case You have been asked by your customer to help resolve issues in their routed network. Their network engineer has deployed HSRP. On closer inspection HSRP doesn't appear to be operating properly and it appears there are other network problems as well. You are to provide solutions to all...
The following debug messages are noticed for HSRP group 2. But still neither R1 nor R2 has identified one of them as standby router. Identify the reason causing the issue.
The following debug messages are noticed for HSRP group 2. But still neither R1 nor R2 has identified one of them as standby router. Identify the reason causing the issue. Note: only show commands can be used to troubleshoot the ticket. R1# 'Mar 26 11:17:39.234: HSRP: Et1/0 Grp 2 Hello...
Examine the configuration on R5. Router R5 do not see any route entries learned from R4; what could be the issue?
Examine the configuration on R5. Router R5 do not see any route entries learned from R4; what could be the issue?A . HSRP issue between R5 and R4B . There is an OSPF issue between R5and R4C . There is a DHCP issue between R5 and R4D . The distribute-list...
What is the solution of the fault condition?
What is the solution of the fault condition?A . enable OSPF Authentication on the S0/0/0 interface using the ip ospf authentication messagedigest commandB . enable OSPF routing on the s0/0/0 interface using the network 10.1.1.0 0.0.0.0.255 area 12 commandC . enable OSPF routing on the s0/0/1 interface using the network...
Please Answer Questions Follow The Prompts Below
BGP sim View AnswerAnswer: R1 configuration Router>enable Router#show running-config show run on R1 can see the following configuration ―-output omitted―- router bgp 64520 network 172.16.1.1 mask 255.255.255.255 neighbor IBGP peer-group neighbor IBGP remote-as 64550 ----wrong AS neighbor IBGP update-source loopback0 neighbor 172.16.2.2 peer-group IBGP neighbor 172.16.3.3 peer-group IBGP neighbor 209.165.200.2...
What is the solution of the fault condition?
What is the solution of the fault condition?A . Under the interface Serial0/0/0 configuration enter the ip nat inside commandB . Under the interface Serial0/0/1 configuration enter the ip nat outside commandC . Under interface Serial0/0/1 delete the “ip nat inside” command and add the “ip nat outside” commandD ....
On Which device is the fault condition located?
Configuration on R1 ip nat inside source list nat_pool interface s0/0/1 overload ip access-list standard nat_pool permit 10.1.0.0 permit 10.2.0.0 ! interface Serial0/0/1 ip address 209.65.200.225 255.255.255.252 ip nat outside ! interface Serial0/0/0.12 ip address 10.1.1.1 255.255.255.252 ip nat outside ip ospf message-digest-key 1 md5 TSHOOT ip ospf authentication message-digest...
