- All Exams Instant Download
Which output is expected in the blank line?
Refer to the exhibit. Which output is expected in the blank line?A . DOWNB . EXSTARTC . LOADINGD . EXCHANGEView AnswerAnswer: B Explanation: Neighbors Stuck in Exstart/Exchange State The problem occurs most frequently when attempting to run OSPF between a Cisco router and another vendor’s router. The problem occurs when...
The following debug messages are noticed for HSRP group 2. But still neither R1 nor R2 has identified one of them as standby router. Identify the reason causing the issue.
The following debug messages are noticed for HSRP group 2. But still neither R1 nor R2 has identified one of them as standby router. Identify the reason causing the issue. Note: only show commands can be used to troubleshoot the ticket. R1# 'Mar 26 11:17:39.234: HSRP: Et1/0 Grp 2 Hello...
User on the 172.16.1.0/24 and 172.16.3.0/24 networks report that they frequently connection at the remote site, what cause of the problem is true?
Refer to the exhibit. User on the 172.16.1.0/24 and 172.16.3.0/24 networks report that they frequently connection at the remote site, what cause of the problem is true?A . recursive routingB . static IP route sC . IP access listD . RIP auto summarizationView AnswerAnswer: A
Fault Condition is related to which technology?
Fault Condition is related to which technology?A . BGPB . NTPC . IP NATD . IPv4 OSPF RoutingE . IPv4 OSPF RedistributionF . IPv6 OSPF RoutingG . IPv4 layer 3 securityView AnswerAnswer: D Explanation: The problem in this situation is with OSPF on router 1. It is missing the "ip...
G1/2 is the root port for SW4, please choose the command so G1/1 can be the new root port?
G1/2 is the root port for SW4, please choose the command so G1/1 can be the new root port?A . spanning-tree cost 1 on interface g1/1B . spanning-tree cost 5 on interface gi0/1C . spanning-tree port priority 0 on g1/1D . spanning-tree port priority 0 on g1/2View AnswerAnswer: B
Which command can be used to apply the INTERNET ACL to an interface in order for traffic to pass?
Refer to the exhibit. Which command can be used to apply the INTERNET ACL to an interface in order for traffic to pass?A . ipv6 access-class INTERNET {in|out}B . ipv6 traffic-filter INTERNET {in|out}C . access-class INTERNET {in|out}D . ip access-group INTERNET {in|out}View AnswerAnswer: B
Which configuration would establish interface Gi1/1 the new root port for VLAN 40?
Refer to the exhibit, interface Gi1/2 is the root port for VLAN 40 on DSW-01. Which configuration would establish interface Gi1/1 the new root port for VLAN 40?A . DSW-01(config)#interface gig1/1 DSW-01(config-if)#spanning-tree port-priority 0B . DSW-01(config)#interface gig1/2 DSW-01(config-if)#spanning-tree port-priority 0C . DSW-01(config)#interface gig1/1 DSW-01(config-if)#spanning-tree cost 1D . DSW-01(config)#interface gig1/2 DSW-01(config-if)#spanning-tree...
65.200.0 0.0.0.255 area 12
65.200.0 0.0.0.255 area 12 command D. redistribute the BGP routes into OSPF using the redistribute BGP 65001 subnet command.View AnswerAnswer: A Explanation: R2 is correctly configured for OSPF authentication, including the "ip ospf authentication message-digest" command listed properly under the sub-interface Serial0/0/0.12. R1 is missing this command.
Which action allows the user to work on the device without interruption?
A Cisco IOS router is disconnecting the console session of a user after some amount of time. Which action allows the user to work on the device without interruption?A . set the exec-timeout 0 0 command on line con 0B . enter the no exec-banner command on line vty 0...
Which two commands can be used to show the number of packets dropped by Unicast RPF?(choose two)
Which two commands can be used to show the number of packets dropped by Unicast RPF?(choose two)A . show ip interfaceB . show interfaceC . show ip cefD . show ip trafficE . show cef interfaceView AnswerAnswer: AD Explanation: With uRPF properly deployed and configured throughout the network infrastructure, administrators...
