- All Exams Instant Download
At a minimum, which four network items must be configured for the endpoint to be able to register with H.323 on a Cisco TelePresence Video Communication Server located at the external headquarters location?
You have installed a C-Series endpoint in an office where DHCP is not supported. At a minimum, which four network items must be configured for the endpoint to be able to register with H.323 on a Cisco TelePresence Video Communication Server located at the external headquarters location? (Choose four.)A ....
Which two video endpoints can you set back to factory reset by using physical button presses? (Choose two.)
Which two video endpoints can you set back to factory reset by using physical button presses? (Choose two.)A . Cisco TelePresence C40B . Cisco TelePresence EX90C . Cisco TelePresence C60D . Cisco TelePresence SX20E . Cisco TelePresence C90View AnswerAnswer: B, D
Which three features does a Cisco TelePresence Content Server provide that a Cisco MCU cannot? (Choose three.)
Which three features does a Cisco TelePresence Content Server provide that a Cisco MCU cannot? (Choose three.)A . conference bridge virtualization supportB . multiple conference layoutsC . resource optimization via conductorD . 720p resolution at 60 fpsE . 1080p resolution at 60 fpsF . multiscreen immersive room endpoint supportView AnswerAnswer:...
What does this red "X" indicate?
A Cisco TelePresence System 1300 Series endpoint is in the process of booting and the engineer notices a red "X" on the screen for Step 6 in the boot process. What does this red "X" indicate?A . The endpoint failed to load its firmware.B . There is an error with...
What are the protocol and direction of the call, the called party, and the transmit rate of the call?
Refer to the exhibit. The screenshots show outputs from the xStatus of a Cisco TelePresence endpoint and the VCS registrations. What are the protocol and direction of the call, the called party, and the transmit rate of the call?A . h.323, incoming, 5919*2345, 1152 Kb/sB . h.323, outgoing, 5919*2345, 1152...
Which step is first in the troubleshooting process?
A customer reports that in a CTS1300 room, a microphone switches to a segment that has no one talking. Which step is first in the troubleshooting process?A . Replace the microphones to stop phantom switching.B . Reseat the microphone cables.C . Recalibrate the microphones.D . Reboot the codec.E . Replace...
Which two methods will retrieve this information?
An engineer wants to know if there is a way to determine the optical zoom of a Cisco TelePresence SX20 remotely. Which two methods will retrieve this information? (Choose two.)A . From the CLI, run xstatus.B . From the CLI, run xconfig.C . From the web GUI, choose Configuration >...
Which step should the engineer take first?
Topic 2, Endpoint Configuration A network engineer wants to automate the monitoring of Cisco TelePresence TX systems. Which step should the engineer take first?A . Configure Cisco TMS on the codec.B . Configure Medianet on the codec.C . Configure NTP on the codec.D . Configure Multiway on the codec.E ....
Which three of these are valid ways to initially configure a C-Series codec in a network where DHCP is not used? (Choose three.)
Which three of these are valid ways to initially configure a C-Series codec in a network where DHCP is not used? (Choose three.)A . Tandberg Remote Control VB . secure copy programC . CLI using a console cableD . touchscreen interfaceE . secure web browserF . TelnetView AnswerAnswer: A, C,...
Which configuration element can be used to specify the Multiway address that can be used by the endpoint to initiate Multiway calls?
Refer to the exhibit. Which configuration element can be used to specify the Multiway address that can be used by the endpoint to initiate Multiway calls?A . Conference 1B . NetworkServicesC . ProvisioningD . SIP Profile 1E . VideoView AnswerAnswer: B
