- All Exams Instant Download
GigabitEthernet 1/1 and 1/2?
Refer to the exhibit. L3SW1 has a spanning-tree priority of 8192 set on VLANs 1, 300, and 301, and these VLANs are configured on and trunked between all switches. Executing the command show spanning-tree blockedports on L2SW5 results in: L2SW5# show spanning-tree blockedports Name Blocked Interfaces List -------------------- ------------------------------------ VLAN0001...
What is the reason that ProfiNET frames are discarded by default on Catalyst switches?
What is the reason that ProfiNET frames are discarded by default on Catalyst switches?A . ProfiNET uses a nonstandard Ethernet frame formatB . The frames have an 802.1q tag with VLAN ID equal to 0 (zero)C . Catalyst switches do not support ProfiNET trafficD . A ProfiNET VLAN must be...
To ensure ProfiNET Layer 2 Class-of-Service markings from ProfiNET devices are trusted by the switch, which command must be entered on the interface attached to the device?
To ensure ProfiNET Layer 2 Class-of-Service markings from ProfiNET devices are trusted by the switch, which command must be entered on the interface attached to the device?A . switch(config-if)#mls qos trust cosB . switch(config-if)#qos trust cosC . switch(config-if)#profinet cos trustD . switch(config-if)#trust qos cosView AnswerAnswer: A
You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on?
You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on?A . Lattency and JitterB . Redundancy and high availabilityC . Explicit and Implicit messagingD ....
If the Link Fault alarm is connected to the minor relay and the FCS Bit Error Rate alarm is connected to the major relay, which commands will create an alarm profile called GigE with the alarms correctly mapped to the minor and major relays?
If the Link Fault alarm is connected to the minor relay and the FCS Bit Error Rate alarm is connected to the major relay, which commands will create an alarm profile called GigE with the alarms correctly mapped to the minor and major relays?A . Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 4...
Which two are possible solutions to control which devices can communicate between industrial zones? (Choose two)
Which two are possible solutions to control which devices can communicate between industrial zones? (Choose two)A . Use per zone private IP addressing and deploy NAT to control traffic between zonesB . Put access control lists on switches connecting industrial zones to control trafficC . Attach each zone to a...
When troubleshooting a high packet loss condition in the network, the inspection area has an assessed M.I.C.E. value of M=1, I=1, C=3 and E=1. Which condition could be suspect?
When troubleshooting a high packet loss condition in the network, the inspection area has an assessed M.I.C.E. value of M=1, I=1, C=3 and E=1. Which condition could be suspect?A . Use of shielded Patch Cables, Bonded on one end only.B . Use of unshielded Patch Cables.C . Broken seal on bulkhead...
Which action will allow you to meet the connectivity requirements?
Refer to the exhibit. You are required to implement traffic segmentation in the network. See the table for relevant device details: L2SW4, L2SW5, and L2SW6 are connected to L3SW1 with 802.1Q trunks with VLAN 191 and VLAN 398 allowed on the trunk. You have the following information from L3SW1: L3SW1# show run interfaces interface...
Which two are possible solutions to control which devices can communicate between industrial zones? (Choose two)
Which two are possible solutions to control which devices can communicate between industrial zones? (Choose two)A . Use per zone private IP addressing and deploy NAT to control traffic between zonesB . Put access control lists on switches connecting industrial zones to control trafficC . Attach each zone to a...
What are three Cisco best practices for running I/O control traffic in a wireless environment? (Choose three)
What are three Cisco best practices for running I/O control traffic in a wireless environment? (Choose three)A . 3200 packets per second and 20% bandwidth for HMI and maintenance traffic.B . 2200 packets per second and 20% bandwidth for HMI and maintenance trafficC . I/O control traffic can be run...
