- All Exams Instant Download
Which standards-based First Hop Redundancy Protocol is a Cisco supported alternative to Hot Standby Router Protocol?
Which standards-based First Hop Redundancy Protocol is a Cisco supported alternative to Hot Standby Router Protocol?A . VRRPB . GLBPC . TFTPD . DHCPView AnswerAnswer: A
What is the default Syslog facility level?
What is the default Syslog facility level?A . local5B . local4C . local6D . local7View AnswerAnswer: D
When an interface is configured with PortFast BPDU guard, how does the interface respond when it receives a BPDU?
When an interface is configured with PortFast BPDU guard, how does the interface respond when it receives a BPDU?A . It continues operating normally.B . It goes into a down/down state.C . It becomes the root bridge for the configured VLAE . It goes into an errdisable state.View AnswerAnswer: D
Which command sequence can you enter to create VLAN 20 and assign it to an interface on a switch?
Which command sequence can you enter to create VLAN 20 and assign it to an interface on a switch?A . Switch (config)#vlan 20 Switch (config)#Interface gig x/y Switch (config-if)#switchport access vlan 20B . Switch (config)#Interface gig x/y Switch (config-if)#vlan 20 Switch (config-vlan)#switchport access vlan 20C . Switch (config)#vlan 20 Switch...
Which two statements about Ethernet standards are true? (choose two)
Which two statements about Ethernet standards are true? (choose two)A . Ethernet is defined by IEEE standard 802.2B . Ethernet is defined by IEEE standard 802.3C . Ethernet 10BASE-T dose not support full-duplex.D . When an Ethernet network uses CSMA/CD, it terminates transmission as soon as collision occursE . When...
Which set of commands is recommended to prevent the use of a hub in the access layer?
Which set of commands is recommended to prevent the use of a hub in the access layer?A . switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1B . switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security mac-address 1C . switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1D . switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1View AnswerAnswer:...
Which spanning-tree protocol rides on top of another spanning-tree protocol?
Which spanning-tree protocol rides on top of another spanning-tree protocol?A . MSTPB . RSTPC . PVST+D . Mono Spanning TreeView AnswerAnswer: A
Which three commands can you use to set a router boot image? (Choose three.)
Which three commands can you use to set a router boot image? (Choose three.)A . Router(config)# boot system flash c4500-p-mz.121-20.binB . Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.binC . Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.binD . Router> boot flash:c180x-adventerprisek9-mz-124-6E . binF . Router(config)#boot flash:c180x-adventerprisek9-mz-124-6G . binH . Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.binView AnswerAnswer: A,B,C
Which definition of a host route is true?
Which definition of a host route is true?A . a route to the exact /32 destination addressB . a route used when a route to the destination network is missingC . a dynamic route learned from a serverD . a route that is manually configuredView AnswerAnswer: A
What is the simplest way to accomplish this?
Refer to the exhibit. The network administrator must establish a route by which London workstations can forward traffic to the Manchester workstations. What is the simplest way to accomplish this?A . Configure a dynamic routing protocol on London to advertise all routes to Manchester.B . Configure a dynamic routing protocol...
