How to create a trunk port and allow VLAN 20? (Choose Three.)

How to create a trunk port and allow VLAN 20? (Choose Three.)A . switchport trunk encapsulation dot1qB . switchport mode trunkC . switchport trunk allowed vlan 20D . switchport trunk native vlan 20View AnswerAnswer: ABC

January 4, 2020 1 Comment READ MORE +

Refer to the exhibit.

Refer to the exhibit. The following commands are executed on interface fa0/1 of 2950Switch. 2950Switch(config-if)# switchport port-security 2950Switch(config-if)# switchport port-security mac-address sticky 2950Switch(config-if)# switchport port-security maximum 1 The Ethernet frame that is shown arrives on interface fa0/1. What two functions will occur when this frameA . The MAC address table...

January 4, 2020 No Comments READ MORE +

Two routers named Atlanta and Brevard are connected via their serial interfaces as illustrated, but they are unable to communicate. The Atlanta router is known to have the correct configuration.

Two routers named Atlanta and Brevard are connected via their serial interfaces as illustrated, but they are unable to communicate. The Atlanta router is known to have the correct configuration. Given the partial configurations, identify the fault on the Brevard router that is causing the lack of connectivity.A . incompatible...

January 3, 2020 No Comments READ MORE +

Which interface counter can you use to diagnose a duplex mismatch problem?

Which interface counter can you use to diagnose a duplex mismatch problem?A . no earnerB . late collisionsC . giantsD . CRC errorsE . deferredF . runtsView AnswerAnswer: B

January 3, 2020 No Comments READ MORE +

Which command can you enter to configure an IPV6 floating static route?

Which command can you enter to configure an IPV6 floating static route?A . Router (config)# ipv6 route FE80:0202::/32 serail 0/1 201B . Router (config)# ipv6 route::/0 serail0/1C . Router (config)# ipv6 route static resolve defaultD . Router (config)# ipv6 route FE80:0202::/32 serail 0/1 1View AnswerAnswer: A

January 3, 2020 No Comments READ MORE +

How to configure RIPv2? (Choose Two.)

How to configure RIPv2? (Choose Two.)A . Enable RIPB . Connect RIP to WAN interfaceC . Enable no auto-summaryD . Enable authentication EView AnswerAnswer: AC

December 31, 2019 No Comments READ MORE +

Which statement about RADIUS security is true?

Which statement about RADIUS security is true?A . It supports EAP authentication for connecting to wireless networks.B . It provides encrypted multiprotocol support.C . Device-administration packets are encrypted in their entirety.D . It ensures that user activity is fully anonymous.View AnswerAnswer: A

December 31, 2019 No Comments READ MORE +

What is the status of port-channel if LACP is misconfigured?

What is the status of port-channel if LACP is misconfigured?A . ForwardingB . EnabledC . DisabledD . errdisabledView AnswerAnswer: C

December 31, 2019 No Comments READ MORE +

Which two statements about wireless LAN controllers are true? (Choose two.)

Which two statements about wireless LAN controllers are true? (Choose two.)A . They can simplify the management and deployment of wireless LANs.B . They rely on external firewalls for WLAN security.C . They are best suited to smaller wireless networks.D . They must be configured through a GUI over HTTP...

December 31, 2019 No Comments READ MORE +

Which command can you enter to set the default route for all traffic to an interface?

Which command can you enter to set the default route for all traffic to an interface?A . router (config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1B . router (config)#ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/1C . router (config-router)#default-information originateD . router (config-router)#default-information originate alwaysView AnswerAnswer: A

December 30, 2019 No Comments READ MORE +