Which interface counter can you use to diagnose a duplex mismatch problem?

Which interface counter can you use to diagnose a duplex mismatch problem?A . no earnerB . late collisionsC . giantsD . CRC errorsE . deferredF . runtsView AnswerAnswer: B

February 24, 2020 No Comments READ MORE +

Which cause of the issue is true?

You are implementing ElGRP between the main office and branch offices. In Phase 1 you must implement and verify EIGRP configurations as mentioned in the topology in Phase 2. your colleague is expected to do NAT and ISP configurations Identity the issues that you are encountering during Phase 1 EIGRP...

February 24, 2020 No Comments READ MORE +

Given the information in the graphic and assuming that the router and switch2 are configured properly, which of the following commands should be issued on switch 1 to correct this problem?

The network administrator cannot to switch 1 over a telnet session, although the hosts attached to switch 1 can ping the interface Fa0/0 of the router. Given the information in the graphic and assuming that the router and switch2 are configured properly, which of the following commands should be issued...

February 23, 2020 No Comments READ MORE +

Which network address and subnet mask meet this requirement?

You have been asked to come up with a subnet mask that will allow all three web servers to be on the same network while providing the max number of subnets. Which network address and subnet mask meet this requirement?A . 192.168.252.8 255.255.255.248B . 192.168.252.8 255.255.255.252C . 192.168.252.16 255.255.255.240D ....

February 23, 2020 No Comments READ MORE +

Which cause of the issue is true?

You are implementing ElGRP between the main office and branch offices. In Phase 1 you must implement and verify EIGRP configurations as mentioned in the topology in Phase 2. your colleague is expected to do NAT and ISP configurations Identity the issues that you are encountering during Phase 1 EIGRP...

February 23, 2020 No Comments READ MORE +

After you configure the Loopback0 interface, which command can you enter to verify the status of the interface and determine whether fast switching is enabled?

After you configure the Loopback0 interface, which command can you enter to verify the status of the interface and determine whether fast switching is enabled?A . Router#show ip interface loopback 0B . Router#show runC . Router#show interface loopback 0D . Router#show ip interface briefView AnswerAnswer: A

February 23, 2020 No Comments READ MORE +

Which plane handles switching traffic through a cisco router?

Which plane handles switching traffic through a cisco router?A . ControlB . DataC . PerformanceD . ManagementView AnswerAnswer: B

February 23, 2020 No Comments READ MORE +

How to create a trunk port and allow VLAN 20? (Choose Three.)

How to create a trunk port and allow VLAN 20? (Choose Three.)A . switchport trunk encapsulation dot1qB . switchport mode trunkC . switchport trunk allowed vlan 20D . switchport trunk native vlan 20View AnswerAnswer: ABC

February 23, 2020 No Comments READ MORE +

Which route or routes will the router install in the routing table?

A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which...

February 23, 2020 No Comments READ MORE +

Refer to the exhibit.

Refer to the exhibit. The following commands are executed on interface fa0/1 of 2950Switch. 2950Switch(config-if)# switchport port-security 2950Switch(config-if)# switchport port-security mac-address sticky 2950Switch(config-if)# switchport port-security maximum 1 The Ethernet frame that is shown arrives on interface fa0/1. What two functions will occur when this frameA . The MAC address table...

February 22, 2020 No Comments READ MORE +