Which two options are valid WAN connectivity methods? (Choose two.)
Which two options are valid WAN connectivity methods? (Choose two.)A . PPPB . WAPC . DSLD . L2TPv3E . EthernetView AnswerAnswer: A, C Explanation: On each WAN connection, data is encapsulated into frames before it crosses the WAN link. The following are typical WAN protocols:
With all routers and interfaces operational, how many networks will be in the routing table of R1 that are indicated to be learned by OSPF?
OSPF is configured using default classful addressing. OSPF is configured using default classful addressing. With all routers and interfaces operational, how many networks will be in the routing table of R1 that are indicated to be learned by OSPF?A . 2B . 3C . 4D . 5E . 6F ....
Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1?
Refer to the exhibit. Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1?A . The router will forward packets from R3 to R2 to R1.B . The router will forward packets from R3 to R1 to R2.C . The...
168.10.192/26 network to a host on the LAN attached to router R1?
168.10.192/26 network to a host on the LAN attached to router R1? R3# show ip route Gateway of last resort is not set 192 168.20.0/24 is variably subnetted, 6 subnets, 2 masks D 192.168.20.64/26 [90/2195456] via 192.168.20.9, 00:03:31, Serial0/0 D 192.168.20.0/30 [90/2681856] via 192.168.20.9, 00:03:31, Serial0/0 C 192.168.20.4/30 is directly...
What two functions will occur when this frame is received by 2950Switch?
Refer to the exhibit. The following commands are executed on interface fa0/1 of 2950Switch. 2950Switch(config-if)# switchport port-security 2950Switch(config-if)# switchport port-security mac-address sticky 2950Switch(config-if)# switchport port-security maximum 1 The Ethernet frame that is shown arrives on interface fa0/1. What two functions will occur when this frame is received by 2950Switch? (Choose...
Which two switch states are valid for 802.1w? (Choose two.)
Which two switch states are valid for 802.1w? (Choose two.)A . listeningB . backupC . disabledD . learningE . discardingView AnswerAnswer: D, E Explanation: Port States There are only three port states left in RSTP that correspond to the three possible operational states. The 802.1D disabled, blocking, and listening states...
Please Answer Questions Follow The Prompts Below
DRAG DROP View AnswerAnswer: Explanation: Enhanced Interior Gateway Routing Protocol (EIGRP) is a Cisco proprietary routing protocol, so it is vendor-specific. By default, EIGRP internal routes have an administrative distance value of 90. OSPF uses cost as its metric. By default, the cost of an interface is calculated based on...
What is true about this configuration?
Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?A . These...
When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?
Refer to the exhibit. When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?A . AS numbers must be changed to match on all the routersB . Loopback interfaces must be configured so a DR is electedC . The no auto-summary command is needed on Router...
Which routers are likely to have been elected as DR?
The internetwork infrastructure of company XYZ consists of a single OSPF area as shown in the graphic. There is concern that a lack of router resources is impeding internetwork performance. As part of examining the router resources, the OSPF DRs need to be known. All the router OSPF priorities are...