What information does a router running a link-state protocol use to build and maintain its topological database? (Choose two.)

What information does a router running a link-state protocol use to build and maintain its topological database? (Choose two.)A . hello packetsB . SAP messages sent by other routersC . LSAs from other routersD . beacons received on point-to-point linksE . routing tables received from other link-state routersF . TTL...

July 1, 2018 No Comments READ MORE +

Which statements represent what is shown?

The command show frame-relay map gives the following output: Serial 0 (up): ip 192.168.151.4 dlci 122, dynamic, broadcast, status defined, active Which statements represent what is shown?(Choose three.)A . 192.168.151.4 represents the IP address of the remote routerB . 192.168.151.4 represents the IP address of the local serial interfaceC ....

June 29, 2018 No Comments READ MORE +

If required, what password should be configured on the DeepSouth router in the branch office to allow a connection to be established with the MidEast router?

If required, what password should be configured on the DeepSouth router in the branch office to allow a connection to be established with the MidEast router? A . No password is required.B . EnableC . SecretD . TelnetE . ConsoleView AnswerAnswer: B Explanation: In the diagram, DeepSouth is connected to...

June 27, 2018 No Comments READ MORE +

If the router Cisco returns the given output and has not had its router ID set manually, what value will OSPF use as its router ID?

Refer to the exhibit. If the router Cisco returns the given output and has not had its router ID set manually, what value will OSPF use as its router ID?A . 192.168.1.1B . 172.16.1.1C . 1.1.1.1D . 2.2.2.2View AnswerAnswer: D Explanation: If a router-id is not configured manually in the...

June 27, 2018 No Comments READ MORE +

Which three of these show the correct RSTP port roles for the indicated switches and interfaces?

Refer to the exhibit. Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.)A . SwitchA,...

June 26, 2018 No Comments READ MORE +

What is the cause for this misconfiguration?

Scenario Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5. The EIGRP routing protocol is configured. You are...

June 25, 2018 No Comments READ MORE +

Why did Branch1 router lose WAN connectivity with R1 router?

Why did Branch1 router lose WAN connectivity with R1 router? A . The IP address is misconfigured on PPP multilink interface on the Branch1 router.B . The PPP multilink group is misconfigured on the £ranch1 serial interfaces.C . The PPP multilink group is misconfigured on the R1 serial interfaces.D ....

June 24, 2018 No Comments READ MORE +

Which part of the PPPoE server configuration contains the information used to assign an IP address to a PPPoE client?

Which part of the PPPoE server configuration contains the information used to assign an IP address to a PPPoE client?A . virtual-template interfaceB . DHCPC . dialer interfaceD . AAA authenticationView AnswerAnswer: A

June 21, 2018 No Comments READ MORE +

Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?

Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?A . IETFB . ANSI Annex DC . Q9333-A Annex AD . HDLCView AnswerAnswer: A Explanation: Cisco supports two Frame Relay encapsulation types: the Cisco encapsulation and the IETF Frame Relay encapsulation, which is in conformance...

June 21, 2018 No Comments READ MORE +

What is the purpose of Inverse ARP?

What is the purpose of Inverse ARP?A . to map a known IP address to a MAC addressB . to map a known DLCI to a MAC addressC . to map a known MAC address to an IP addressD . to map a known DLCI to an IP addressE ....

June 19, 2018 No Comments READ MORE +