What happens if you apply a hotfix using gClish?
What happens if you apply a hotfix using gClish? A. If you apply a hotfix using gclish, it causes an outage for the entire SG as all members reboot at roughly the same time. B. If you apply a hotfix using gclish, each SG members installs the hotfix and reboots...
What is the purpose of RJ-45 connectors located at the front panel of the Orchestrator MHO-170?
What is the purpose of RJ-45 connectors located at the front panel of the Orchestrator MHO-170?A . Two Out-of-band interfaces for access to Orchestrator itselfB . 1Gbps connectivity for Security GroupsC . Out-of-band interface for access to Orchestrator itself and Serial Console connectorD . Reserved for internal purposes. Not in...
What is a downlink interface used for?
What is a downlink interface used for?A . To connect appliances to OrchestratorsB . To connect appliances to customer's infrastructureC . To connect in between OrchestratorsD . To connect Orchestrators to customer's infrastructureView AnswerAnswer: B
What is the purpose of Management ports located on the Rear Panel of the Orchestrator MHO-140?
What is the purpose of Management ports located on the Rear Panel of the Orchestrator MHO-140?A . 1Gbps connectivity for Security GroupsB . Reserved for internal purposes. Not in use.C . Out-of-band interfaces for access to Orchestrator itselfD . Additional ports used as uplinksView AnswerAnswer: C Explanation: The Management ports...
What kinds of transceivers are supported on Orchestrator MHO-140?
What kinds of transceivers are supported on Orchestrator MHO-140?A . SFP, QSFP, QSFP28B . SFP+, SFP28, QSFPC . SFP, SFP+, SFP28D . SFP, SFP+, QSFP, QSFP28View AnswerAnswer: D Explanation: The Orchestrator MHO-140 supports a wide range of transceiver types, including SFP, SFP+, QSFP, and QSFP28. This range of compatibility allows...
The ______________ command will allow users to update the specified file on all SGMs.
The ______________ command will allow users to update the specified file on all SGMs.A . g_update_conf_fileB . g_all"C . sedD . g_catView AnswerAnswer: A Explanation: The g_update_conf_file command is a global command that allows users to update the specified file on all Security Group Members of the current Security Group....
What cannot be learned from the output of lldpctl?
What cannot be learned from the output of lldpctl?A . Serial number of ApplianceB . Appliance modelC . Distribution modeD . Orchestrator's IPView AnswerAnswer: C Explanation: The lldpctl command is a tool to display information about the devices discovered by the Link Layer Discovery Protocol (LLDP) on all ports of...
Which interfaces should be connected to Orchestrator 1 for downlinks' intra-orchestrator redundancy when using two Orchestrators?
There are two 10Gbps dual-port NICs and one 40Gbps NIC installed on a 23800 Appliance in slots 1, 2 and 3 accordingly. Which interfaces should be connected to Orchestrator 1 for downlinks' intra-orchestrator redundancy when using two Orchestrators?A . Port 1 in Slot 2 and Port 2 in Slot 1B...
What happens if the SMO Master fails?
What happens if the SMO Master fails?A . The next SGM with the current lowest SGM ID assumes the role of the SMO Master.B . The Backup SMO Master will take over in the event of a failure with the SMO Master.C . A failover will occur on the MHO...
What is the Orchestrator?
What is the Orchestrator?A . Network SwitchB . Manager of compute and network resources, load balancer and network switchC . Load balancerD . None of aboveView AnswerAnswer: B Explanation: The Orchestrator is a Maestro component that manages the compute and network resources of the Security Group Modules (SGMs) in a...