- All Exams Instant Download
Which address are OSPF hello packets addressed to on point-to-point networks?
Which address are OSPF hello packets addressed to on point-to-point networks?A . 224.0.0.5B . 172.16.0.1C . 192.168.0.5D . 223.0.0.1E . 254.255.255.255View AnswerAnswer: A Explanation: Why Does the show ip ospf neighbor Command Reveal Neighbors in the Init State? http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080093f11.shtml OSPF hello packets have a destination address of 224.0.0.5 (the all...
What would be the most effective steps to troubleshoot this physical layer problem?
Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem? (Choose three.)A . Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.B . Ensure that cables...
Select two options which are security Issues which need to be modified before RouterA is used?
Hotspot Questions Select two options which are security Issues which need to be modified before RouterA is used? (Choose two.)A . unencrypted weak password is configured to protect privilege modeB . inappropriate wording in banner messageC . the virtual terminal lines have a weak password configuredD . virtual terminal lines...
Drag and Drop Question
Drag and Drop Question On the left are various network protocols. On the right are the layers of the TCP/IP model. Assuming a reliable connection is required, move the protocols on the left to the TCP/IP layers on the right to show the proper encapsulation for an email message sent...
Given an IP address of 192.168.1.42 255.255.255.248, what is the subnet address?
Given an IP address of 192.168.1.42 255.255.255.248, what is the subnet address?A . 192.168.1.8/29B . 192.168.1.32/27C . 192.168.1.40/29D . 192.168.1.16/28E . 192.168.1.48/29View AnswerAnswer: C Explanation: 248 mask uses 5 bits (1111 1000) 42 IP in binary is (0010 1010) The base subnet therefore is the lowest binary value that can...
To allow or prevent load balancing to network 172.16.3.0/24, which of the following commands could be used in R2? (Choose two.)
To allow or prevent load balancing to network 172.16.3.0/24, which of the following commands could be used in R2? (Choose two.) A . R2(config-if)#clock rateB . R2(config-if)#bandwidthC . R2(config-if)#ip ospf costD . R2(config-if)#ip ospf priorityE . R2(config-router)#distance ospfView AnswerAnswer: BC Explanation: http://www.cisco.com/en/US/tech/tk365/technologies_white_paper09186a0080094e9e.sht ml#t6 The cost (also called metric) of an...
If the resume command is entered after the sequence that is shown in the exhibit, which router prompt will be displayed?
Refer to the exhibit. If the resume command is entered after the sequence that is shown in the exhibit, which router prompt will be displayed?A . Router1>B . Router1#C . Router2>D . Router2#View AnswerAnswer: C Explanation: The Ctrl-Shift-6 x command suspends the telnet session and hence the prompt will again...
What does administrative distance refer to?
What does administrative distance refer to?A . the cost of a link between two neighboring routersB . the advertised cost to reach a networkC . the cost to reach a network that is administratively setD . a measure of the trustworthiness of a routing information sourceView AnswerAnswer: D Explanation: Administrative...
Which two characteristics describe the access layer of the hierarchical network design model? (Choose two.)
Which two characteristics describe the access layer of the hierarchical network design model? (Choose two.)A . layer 3 supportB . port securityC . redundant componentsD . VLANsE . PoEView AnswerAnswer: BD Explanation: The primary function of an access-layer is to provide network access to the end user. The hardware and...
Which routers are likely to have been elected as DR?
The internetwork infrastructure of company XYZ consists of a single OSPF area as shown in the graphic. There is concern that a lack of router resources is impeding internetwork performance. As part of examining the router resources, the OSPF DRs need to be known. All the router OSPF priorities are...
