- All Exams Instant Download
Using the switch output shown, what is the cause of the problem?
Refer to the exhibit. An administrator replaced the 10/100 Mb NIC in a desktop PC with a 1 Gb NIC and now the PC will not connect to the network. The administrator began troubleshooting on the switch. Using the switch output shown, what is the cause of the problem? A....
Drag and Drop Question
Drag and Drop Question Various protocols are listed to the left. On the right are applications for the use of those protocols. Drag the protocol on the left to an associated function for that protocol on the right. (Not all options are used) View AnswerAnswer:
What will the switch do when it receives the frame from host A?
Refer to the exhibit. The exhibit is showing the topology and the MAC address table. Host A sends a data frame to host D. What will the switch do when it receives the frame from host A? A. The switch will add the source address and port to the MAC...
What will be the source IP address of the packet as it leaves the Kiev router?
Refer to the exhibit. The host in Kiev sends a request for an HTML document to the server in Minsk. What will be the source IP address of the packet as it leaves the Kiev router?A . 10.1.0.1B . 10.1.0.5C . 10.1.0.6D . 10.1.0.14E . 10.1.1.16F . 10.1.2.8View AnswerAnswer: E...
Based on the given information, what is the problem?
Refer to the exhibit. A host is connected to switch port fa0/3. The host and switch have been fully configured for IP connectivity as shown. However, the indicator LED on switch port fa0/3 is not on, and the host cannot communicate with any other hosts including those connected to VLAN...
What is the best practice when assigning IP addresses in a small office of six hosts?
What is the best practice when assigning IP addresses in a small office of six hosts?A . Use a DHCP server that is located at the headquarters.B . Use a DHCP server that is located at the branch office.C . Assign the addresses by using the local CDP protocol.D ....
Which parameter or parameters are used to calculate OSPF cost in Cisco routers?
Which parameter or parameters are used to calculate OSPF cost in Cisco routers?A . BandwidthB . Bandwidth and DelayC . Bandwidth, Delay, and MTUD . Bandwidth, MTU, Reliability, Delay, and LoadView AnswerAnswer: A Explanation: The well-known formula to calculate OSPF cost is Cost = 108 / Bandwidth
What is the purpose of the last command entered?
The following commands are entered on the router: Burbank(config)# enable secret fortress Burbank(config)# line con 0 Burbank(config-line)# login Burbank(config-line)# password n0way1n Burbank(config-line)# exit Burbank(config)# service password-encryption What is the purpose of the last command entered?A . to require the user to enter an encrypted password during the login processB ....
At which OSI layer should the administrator begin troubleshooting?
A network administrator cannot connect to a remote router by using SSH. Part of the show interfaces command is shown. router#show interfaces Serial0/1/0 is up, line protocol is down At which OSI layer should the administrator begin troubleshooting?A . physicalB . data linkC . networkD . transportView AnswerAnswer: B Explanation:...
Which option is a valid IPv6 address?
Which option is a valid IPv6 address?A . 2001:0000:130F::099a::12aB . 2002:7654:A1AD:61:81AF:CCC1C . FEC0:ABCD:WXYZ:0067::2A4D . 2004:1:25A4:886F::1View AnswerAnswer: D Explanation: http://www.ipv6.com/articles/general/IPv6-Addressing.htm IPv6 Address Notation IPv6 addresses are denoted by eight groups of hexadecimal quartets separated by colons in between them. Following is an example of a valid IPv6 address: 2001:cdba:0000:0000:0000:0000:3257:9652 Any four-digit...
