Exam4Training

Nutanix NCA-5.20 Nutanix Certified Associate (NCA) 5.20 Exam Online Training

Question #1

What should an administrator do after a Protection Domain is migrated?

  • A . Register Virtual Machines
  • B . Restore Virtual Machines
  • C . Mount datastores on Hosts
  • D . Power on Virtual Machines

Reveal Solution Hide Solution

Correct Answer: D
Question #2

What is required to successfully live migrate a VM Between two AHV clusters?

  • A . Stretch L2 networks across the primary and recovery sites
  • B . Configure a Protection domain with synchronous replication
  • C . Install and Configure the witness VM on a third Site.
  • D . Both clusters must be managed by the same prism central

Reveal Solution Hide Solution

Correct Answer: B
B

Explanation:

Reference:

Please Re Check From your Side and let me know if the question correction is required

Question #3

An administrator should use which Nutanix component to to create in-guest clustering?

  • A . Storage Pools
  • B . Volumes
  • C . Blocks
  • D . Containers

Reveal Solution Hide Solution

Correct Answer: B
Question #4

An application vendor had provided a VHD disk for their pre-configured virtual machine.

A Nutanix cluster administrator imported that VHD disk into Image Configuration, but the disk does not list while using Clone from Image Service

Before uploading the vDisk again, which two actions should the administrator perform? (Choose two.)

  • A . Convert VHD to QCOW before uploading
  • B . Verify correct container is selected
  • C . Verify the Image is as type Disk
  • D . Verify the Image is Active

Reveal Solution Hide Solution

Correct Answer: A,C
Question #5

Which two Protection Domain features require a configured schedule of less than 15 minutes? (Choose two.)

  • A . Metro Availability DR
  • B . Synchronous DR
  • C . Asynchronous DR
  • D . NearSyncRD

Reveal Solution Hide Solution

Correct Answer: A,D
Question #6

What Nutanix product provides multi-cloud cost and security governance?

  • A . Era
  • B . Leap
  • C . Beam
  • D . Flow

Reveal Solution Hide Solution

Correct Answer: C
Question #7

Refer to the exhibit.

What is indicated by the yellow area of the chart?

  • A . Normal utilization
  • B . Critical alerts
  • C . Warning alerts
  • D . Abnormal utilization

Reveal Solution Hide Solution

Correct Answer: C
Question #8

Which policy specifies that a selected VM will only run on a specific group of nodes?

  • A . Isolation
  • B . Anti-affinity
  • C . Affinity
  • D . Fixed

Reveal Solution Hide Solution

Correct Answer: C
Question #9

An administrator has been asked to investigate performance issues for a business critical application. The application runs on a single VM.

What is easiest way for the administrator to begin troubleshooting this issue?

  • A . On the Analysis page, create an entity chart with all metrics included
  • B . On the Health page, look for Critical or Warning alerts for the VM.
  • C . Review the metrics charts on the Prism Element Home page
  • D . Review the VM Performance tab for the VM in Prism Element

Reveal Solution Hide Solution

Correct Answer: A
Question #10

An administrator wants to ensure that a particular VM starts before any other VM in the environment after performing maintenance.

How can the administrator achieve this?

  • A . Marie the VM as a High Priority VM in Prism Central
  • B . Mark the VM for Host Affinity in Prism Element
  • C . Mark the VM as an Agent VM in Prism Element
  • D . Mark the VM as a High Priority VM in Prism Element

Reveal Solution Hide Solution

Correct Answer: A,C

Question #11

A mission critical application with four VMs have been deployed inside of a six-node Nutanix cluster. An alert is generated that a node in the cluster has failed and is no longer online. After the alert, two of the VMs reboot and come back online on another node.

Which feature, when configured, would have prevented the two VMs from rebooting?

  • A . Host Anti-Affinity
  • B . VM High Availability
  • C . Host Affinity
  • D . Protection Domain

Reveal Solution Hide Solution

Correct Answer: C
Question #12

An administrator is managing two AHV and vSphere-based clusters. The administrator is able to install a Windows Guest OS from an ISO Image to VMware VMs, but is unable to do the same activity with AHV VMs.

What should the administrator do to successfully perform this action with AHV VMs?

  • A . Verify cluster iSCSI Data Services IP
  • B . Provide virtIO Drivers
  • C . Manage Nutanix Guest Tools
  • D . Change VM settings from BIOS to UEFi

Reveal Solution Hide Solution

Correct Answer: B
Question #13

How can an administrator access a Windows VM running on a Nutanix cluster if it is unreachable via ping?

  • A . Connect using Xi Frame
  • B . Open a Virtual Console through Prism Central
  • C . Connect using RDP
  • D . Open a Virtual Console through Prism Element

Reveal Solution Hide Solution

Correct Answer: D
Question #14

After adding a remote site cluster, an administrator must map which two entities? (Choose two.)

  • A . Networks
  • B . Virtual Machines
  • C . Consistency Groups
  • D . VStores

Reveal Solution Hide Solution

Correct Answer: B,C
Question #15

Refer to the exhibit.

An administrator has created a new VM, but when accessing the console to monitor the guest install, the administrator sees the error shown in the exhibit

What is the likely cause of this issue?

  • A . The installation media was not mounted.
  • B . The wrong type of disk was specified.
  • C . The boot order is incorrectly configured.
  • D . The Nuianix VirtlO driver (SO was not mounted.

Reveal Solution Hide Solution

Correct Answer: A
Question #16

Which statement best defines Replication Factor 2 (RF2)?

  • A . Data will be written locally, and a second copy then will be replicated to another cluster
  • B . Data will be written locally, and a second copy to another disk group
  • C . Data will be written locally, and a second copy goes to a remote site
  • D . Data will be written locally, and a second copy goes to another node in the same cluster

Reveal Solution Hide Solution

Correct Answer: D
Question #17

An administrator attempts to reinstall a VM’s QuestOS, hut h unable to change the legacy BIOS hoot priority.

Based on the exhibit, what is causing this issue?

  • A . GuestOS reinstall is not possible for a VM
  • B . The CD-ROM is empty
  • C . The VM is currently on
  • D . The VM is undergoing a snapshot

Reveal Solution Hide Solution

Correct Answer: C
Question #18

An administrator wants to copy some virtual machine disk files to ADSF from an external VMware ESXi host.

Which two actions should the administrator take to complete this task? (Choose two.)

  • A . Mount container as NFS on external host
  • B . Configure Volume Group
  • C . Enable CHAP on Volume Group
  • D . Configure whitelist on container

Reveal Solution Hide Solution

Correct Answer: A,D
Question #19

An administrator completed a successful AOS upgrade, but saw the following alert the following day:

Detected incompatible AHV version What is most likely causing this alert?

  • A . The upgraded AOS version is incompatible with AHV.
  • B . AHV was upgraded manually prior to AOS upgrade.
  • C . AHV is not at the version that carte with the upgraded AOS.
  • D . NCC version is not compatible with the current AHV version.

Reveal Solution Hide Solution

Correct Answer: C
Question #20

Protection Domains enable administrators to replicate which two items for Disaster Recovery? (Choose two-)

  • A . Volume Groups
  • B . Virtual Machines
  • C . File Shares
  • D . Disk Images

Reveal Solution Hide Solution

Correct Answer: A,B

Question #21

Prism Central is managing two clusters, one AHV-based and one vSphere-based vSphere cluster using a stored Prism image, without success.

Why is the administrator experiencing this issue?

  • A . The Image Service applies only to AHY clusters.
  • B . The Virtual Hardware in the image does not match the vSphere version.
  • C . The template image needs to be converted to a VM.
  • D . The template image has not been uploaded to the vSphere cluster.

Reveal Solution Hide Solution

Correct Answer: B
Question #22

A customer requires the ability to block all network traffic between their VDI VMs and their application VMs running on their Nutanix AHV clusters.

What Nutanix product would meet this requirement?

  • A . Beam
  • B . Calm
  • C . Era
  • D . Flow

Reveal Solution Hide Solution

Correct Answer: D
Question #23

An administrator is looking to store a large amount of unstructured data with capabilities to set up a retention policy.

Which Nutanix product meets this requirement?

  • A . Nutanix Mint
  • B . Nutanix Piles
  • C . Nutanix Storage Container
  • D . Nutanix Objects

Reveal Solution Hide Solution

Correct Answer: D
Question #24

Which component allows you to pair sites for Disaster Recovery Policy Creation using Nutanix Leap?

  • A . Protection Policies
  • B . Protection Domains
  • C . Recovery Plan
  • D . Availability Zones

Reveal Solution Hide Solution

Correct Answer: D
Question #25

Nutanix Support Asked an administrator to provide AHV logs to help solve a support request.

Which task should be performed to provide log files to the support team?

  • A . Run NCC Check from the command line
  • B . Upload log files from /home/nutanix/data/logs folder
  • C . collect logs from the health Page
  • D . Enable Pulse to include additional support information

Reveal Solution Hide Solution

Correct Answer: A
Question #26

An organization runs several core business applications on a Nutanix cluster. System stability and support are critical for these applications, which has an annual maintenance window.

How can the administrator assure that these requirements are met?

  • A . Purchase Mission Critical support.
  • B . Purchase Ultimate licensing.
  • C . Adhere to the STS release cycle.
  • D . Adhere to the LTS release cycle.

Reveal Solution Hide Solution

Correct Answer: B
Question #27

An administrator needs to provide data integrity at the application level for a VM that is replicated to a secondary site.

Which requirement will satisfy this task?

  • A . 1 VM per Consistency Group
  • B . 1 VM per Availability Zone
  • C . 1 VM per Protection Domain
  • D . 1 VM per Schedule

Reveal Solution Hide Solution

Correct Answer: D
Question #28

An administrator needs to have a view of current workloads sorted by vCPU count.

What should the administrator do to achieve this task?

  • A . Create a New Dashboard adding the VMs widget
  • B . Use the Group function in prism Central
  • C . Create a new Analysis in Prism Element
  • D . Export the VM list in CSV and use an external tool

Reveal Solution Hide Solution

Correct Answer: A
Question #29

Which Component Allows you to pair sites for disaster Recovery Policy Creation Using Nutanix Leap?

  • A . Availability Zones
  • B . Protection Domains
  • C . Recovery Plans
  • D . Protection Policies

Reveal Solution Hide Solution

Correct Answer: A
Question #30

Refer to the exhibit.

An administrator notices that the Data Resiliency Statue of some components has been reduced to 0. making it impossible to support a node failure in the cluster.

What type of failure is most likely the cause of this issue?

  • A . Block
  • B . Disk
  • C . CVM
  • D . Nods

Reveal Solution Hide Solution

Correct Answer: C

Question #31

An administrator wants to deploy a virtual desktop solution on a Nutanix cluster and wants to use the existing production network segment. Due to security concerns, DHCP traffic is blocked on the upstream network switch.

How should the administrator proceed?

  • A . Enable IPAM and configure an IP Address Pool
  • B . Enable Nutanix Flow
  • C . Enable DHCP on the TOR Switches
  • D . Install and configure third-party DHCP Software

Reveal Solution Hide Solution

Correct Answer: A
Question #32

An Administrator has created a Volume Group for a specific VM on an AHV Cluster.

What is the next step required to user vDisk in the VM?

  • A . Attach the Volume Group to the VM
  • B . Configure CHAP Authentication
  • C . Reboot the VMD. Bring the disk Online

Reveal Solution Hide Solution

Correct Answer: A
Question #33

A new Project is being rolled out to an AHV cluster being monitored by Prism Central. The applications team indicates that the application managed by the project is very memory intensive. The administrator wants to be notified about any memory constraints, should they occur.

How would an administrator most effectively achieve this task?

  • A . Search for the VM, then in the Details page go to metrics and select CPU Usage.
  • B . Create a new Metric chart for the duster, and analyze Hypervisor Memory Usage.
  • C . Create a Report to tracking the Memory Usage.
  • D . Create a new Alert Policy for Memory Usage and set to Critical after 80%.

Reveal Solution Hide Solution

Correct Answer: D
Question #34

Which two entity types can be exported by an administrator who only has access to Prism Element? (Choose two.)

  • A . VM
  • B . Storage
  • C . Health
  • D . Network

Reveal Solution Hide Solution

Correct Answer: A,B
Question #35

An administrator has received the following critical alert:

Node 192.168.148.172 is marked to be detached from metadata. The administrator has opened a case with Nutanix and the support engineer has requested more information about the error.

Which two actions should the administrator take in the Health Check dashboard to collect the requested information? (Choose two.)

  • A . Create an Entity chart
  • B . Open a remote support tunnel.
  • C . Run the Log Collector
  • D . Run the Nutanix Cluster Check

Reveal Solution Hide Solution

Correct Answer: C,D
Question #36

Refer to the exhibit.

An administrator notices that the Data Resiliency Status of some components has been reduced to 0. making it impossible to support a node failure in the cluster.

What failed component caused this issue?

  • A . CVM
  • B . Disk
  • C . Node
  • D . Block

Reveal Solution Hide Solution

Correct Answer: A
Question #37

Which Nutanix component can be placed into a third site, in order to assist the primary and secondary sites during a failure event?

  • A . Backup Server
  • B . Witness VM
  • C . Prism Central
  • D . Controller VM

Reveal Solution Hide Solution

Correct Answer: B
Question #38

Which Nutanix concept is responsible for accommodating and remediating node failure scenarios?

  • A . Life cycle management
  • B . Auto resolve mode
  • C . Data locality
  • D . Self healing

Reveal Solution Hide Solution

Correct Answer: C
Question #39

An administrator needs to upgrade AOS for an air gapped cluster by using Prism Element.

Which two actions allow the administrator to perform the upgrade? Choose Two

  • A . Extract the AOS binaries to the CVM
  • B . Manually Upload Binaries to a local http server
  • C . Manually Upload AOS binaries and metadata
  • D . Use the LCM dark site Option Providing AOS Binaries

Reveal Solution Hide Solution

Correct Answer: C,D
Question #40

An administrator has a SQL VM running, which is experiencing high disk latency.

What could the administrator do to alleviate this?

  • A . Increase CPU and Memory on the CVM
  • B . Attach additional Volume Groups to the VM
  • C . Add more CPU and Memory to the VM
  • D . Create another Storage Container

Reveal Solution Hide Solution

Correct Answer: D
Exit mobile version