Network Appliance NS0-520 NetApp Certified Implementation Engineer – SAN, ONTAP Online Training
Network Appliance NS0-520 Online Training
The questions for NS0-520 were last updated at Jan 07,2025.
- Exam Code: NS0-520
- Exam Name: NetApp Certified Implementation Engineer - SAN, ONTAP
- Certification Provider: Network Appliance
- Latest update: Jan 07,2025
Click the Exhibit button.
During pre-deployment testing, you want to ensure that all FC paths are available to your host. You use the network interface modify -vserver SVM1 -lif LIF_top-0f-admin-state up command to correct the configuration shown in the exhibit.
What happens when using this command?
- A . It creates a new LIF on SVM2 named up.
- B . It creates a new LIF on SVM1 named LIF_top-0f.
- C . It changes the administrative state from "down" to "up".
- D . It changes the operational state from "down" to "up".
You are configuring both NVMe and FC on the same AFF A700 2-node ONTAP 9.5 cluster. You are also configuring both protocols on the same FC fabric using the same A700 HBA ports.
In this scenario, which three configurations are supported? (Choose three.)
- A . 16 GB HBAs
- B . 8 GB HBAs
- C . 16 GB fabrics
- D . 32 GB HBAs
- E . 32 GB fabrics
An administrator needs to determine the maximum volume size that is supported per operating system.
Which resource has this information?
- A . Config Advisor
- B . OneCollect
- C . Interoperability Matrix Tool (IMT)
- D . Hardware Universe (HWU)
An administrator is adding new hosts to a vSphere cluster. The cluster uses the FC protocol to connect to a NetApp cluster. The administrator wants to configure the multipathing for the ESXi host.
Which NetApp tool should be used to accomplish this task?
- A . OnCommand System Manager (OCSM)
- B . Host Utilities
- C . SnapCenter plug-in
- D . NetApp Virtual Storage Console (VSC)
An administrator is asked to configure NVMe on an ONTAP 9.5 cluster for host access.
Which three steps must the administrator perform to accomplish this task? (Choose three.)
- A . Create a namespace
- B . Provision a subsystem
- C . Configure the FC port
- D . Gather the IQN from the host initiator software
- E . Gather the NQN from the host system
A user cannot add more than one NVMe data LIF in ONTAP 9.4 on an SVM with a data protocol parameter set to nvme.
In this scenario, what is the problem?
- A . The SVM data protocol should be set to FC.
- B . The NVMe namespace is not created.
- C . A demo license is used.
- D . Only one NVMe data LIF can be configured per SVM.
An administrator has six VMware hosts, each with dual HBAs that are connected to a dual fabric using single initiator multiple target zoning. Four nodes are being added to the existing 4-node ONTAP cluster.
In this scenario, what is the minimum number of FC zones that need to be updated on each fabric switch?
- A . 6
- B . 8
- C . 4
- D . 2
An administrator has an AFF A200 cluster at their primary site that is used for FC connectivity to servers. For disaster recovery purposes they want to start replicating their data to another AFF A3Q0 cluster In a secondary location.
The AFF A300 is In a site that has no FC or FCoE capable switches, and is currently only used for CIFS data. A cluster peering relationship already exists between the two clusters.
Which three additional actions are needed for the data to be ready for access from hosts at the secondary site? (Choose three.)
- A . Create zones with the appropriate initiators and targets for the secondary site.
- B . Enable the iSCSI service on the SVM at the secondary site.
- C . Replicate the data from the primary site to the secondary site with SnapMirror.
- D . Create new iSCSI igroups for LUN mapping.
- E . Enable the iSCSI service on the SVM at the primary site.
Latest NS0-520 Dumps Valid Version with 334 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
