What would be the minimum configuration required to support a drawer-protected 20-drive DDP? (Choose the best answer.)
- A . An E2624 with four DE5600 Expansion Chassis, containing a total of 6, 1.6TB SSD and 96, 3T NL-SAS drives.
- B . An E5460 with one DE6600 Expansion Chassis, containing a total of 120, 3TB NL-SAS drives.
- C . An E2712 with one DE6600 Expansion Chassis, containing a total of 72, 3TB NL-SAS drives.
- D . An E5424 with one DE5600 Expansion Chassis, containing a total of 48, 900GB SAS drives.
What uses the Access Volume? (Choose the best answer.)
- A . Legacy operating environments
- B . XOR parity calculations
- C . Asymmetric Logical Unit
- D . Redundancy Check
- E . SMagent
What is a NetApp best practice recommendation for the system monitor?
- A . It should be stopped during a controller firmware upgrade.
- B . It should run only on one management server connected to the storage system.
- C . It should run on all storage manager clients.
- D . It should run only on Windows server systems.
What are two types of logical structures that volumes in the E-Series system use? (Choose two.)
- A . volume groups
- B . disk pools
- C . aggregates
- D . volume pools
When data is written to a snapshot, volume is stored __________. (Choose the best answer.)
- A . on the base volume for that snapshot
- B . on the repository area associated with the snapshot’s corresponding image
- C . on the repository associated with the snapshot volume
- D . on the common repository for the snapshot group
- E . on a hot spare drive
Exhibit:
Referring to the exhibit, what is the total number of ALUA paths from the host to a volume on the EF280?
- A . 8
- B . 6
- C . 2
- D . 4
Witch function does the SANtricity Enterprise Management Window (EMW) provide? (Choose the best answer.)
- A . a device discovery option for storage systems to be managed
- B . a multipath I/O driver
- C . volume reconstruction progress updates
- D . a Manage Host Port Identifiers dialog box
- E . a configuration interface for creating disk pools and volume groups
Hot spares provide which function? (Choose the best answer.)
- A . both "efficiency for volumes" and "reserve capacity for disk pools"
- B . efficiency for volumes
- C . reserve capacity for disk pools
- D . reserve capacity for volume groups
- E . None of the above
What are two base host connectivity selections that are provided by the E2800 controller? (Choose two.)
- A . FC
- B . SAS
- C . IB
- D . iSCSI
Which file contains the configuration for a multipath driver for FC on Linux systems?
- A . /opt/multipath/multipath.cnf
- B . /etc/multipath.conf
- C . /etc/dm-multipath.conf
- D . /etc/kernel/mp.conf
If an FDE disk fails, which characteristic is required of the replacement disk?
- A . Must be FDE capable
- B . Must be loaded with DACstore
- C . Must be of a greater capacity
- D . Must be T10-P1 capable
Exhibit:
Which fiber cable end shown in the exhibit is supported on a NetApp E-Series system?
- A . 1
- B . 2
- C . 3
- D . 4
Exhibit:
You ordered a NetApp E2812 Duplex 16GB 10GbE Base-T system.
Referring to the exhibit, what is the maximum number of 10GbE Base-T ports available to be used?
- A . 6
- B . 8
- C . 4
- D . 12
What is the SANtricity Client? (Choose the best answer.)
- A . A host I/O performance modeling interface
- B . A GUI or CLI run on a host server used for storage system management
- C . Inter-process communication that supports computer program subordinates
- D . An OS-dependent collection of utilities for servers attached to SANtricity-managed storage systems
- E . A host server process that enables storage system management with the storage data path
Which support data file provides a description of all the hardware, logical components, and properties of the storage system?
- A . Storage-array-configuration.cfg
- B . Storage-array-profile.txt
- C . Recovery-guru.html
- D . Connection.txt
A customer has an E-Series system with several expansion enclosures and can use the ______ to determine if the connections between the enclosures have been cabled correctly. (Choose the best answer.)
- A . Recovery Guru
- B . Major Event Log
- C . Host Mappings tab
- D . Cable Connections report
Which feature under SANtricity 11.x which requires an activation key? (Choose the best answer.)
- A . Volume copy
- B . Snapshot copies
- C . Mirroring
- D . Drive Security
What mechanism governs control of the E-Series storage premium features? (Choose the best answer.)
- A . simple password system
- B . special USB flash drive that must be inserted into the controllers
- C . small toggle switches on the controller boards inside the system
- D . key file obtained from vendor and passed to system via SANtricity
- E . online database requiring the controllers to access the internet to activate features
The interval for an asynchronous mirror group should usually be equal to ______________. (Choose the best answer.)
- A . the corresponding application’s RPO
- B . half the corresponding application’s RPO
- C . half the corresponding application’s RTO
- D . the corresponding application’s RTO
- E . the amount of time required to copy the size of the mirror repository to the remote site
What measurement refers to how much data can be handled in a given time period? (Choose the best answer.)
- A . Read modify write
- B . Throughput
- C . IOPS
- D . Parity
- E . I/O alignment
During a routine review of firewall logs, an analyst identified that an IP address from the organization’s server subnet had been connecting during nighttime hours to a foreign IP address, and had been sending between 150 and 500 megabytes of data each time. This had been going on for approximately one week, and the affected server was taken offline for forensic review.
Which of the following is MOST likely to drive up the incident’s impact assessment?
- A . PII of company employees and customers was exfiltrated.
- B . Raw financial information about the company was accessed.
- C . Forensic review of the server required fall-back on a less efficient service.
- D . IP addresses and other network-related configurations were exfiltrated.
- E . The local root password for the affected server was compromised.
Which three factors should you consider before you install an E2860 in a data center? (Choose three)
- A . current draw
- B . electromagnetic interference
- C . heat dissipation
- D . ambient temperatures
- E . fire suppression capacity
What does the storage system use to preserve cache data in the event of a complete controller failure? (Choose the best answer.)
- A . Cache mirroring
- B . Flash read cache
- C . Pre-fetch caching
- D . Read caching
- E . Write caching
You are troubleshooting a customer issue on their E-Series system. You need information on the volume configuration of the customer’s system.
In this scenario, which log would you download to get the required information?
- A . Trace Buffers
- B . Support Data
- C . Health Image
- D . IO Path Statistics
Which feature used on E-Series controllers enables them to ship I/O to the alternate controller?
- A . ALUA
- B . AVT
- C . TPGS
- D . RDAC
An administrator is asked to provision a 1 TB volume to hold non-critical temporary data for a seismic-analysis application. The volume requires the highest possible IOPS.
In this scenario, which configuration would satisfy this requirement?
- A . RAID 6 Dynamic Disk Pool with a 256 KiB segment size
- B . RAID 5 volume group with a 256 KiB segment size
- C . RAID 0 volume group with a 32 KiB segment size
- D . RAID 6 Dynamic Disk Pool with a 32 KiB segment size
Which two local users of NetApp SANtricity Unified Manager would be used to edit the Certificate Management section? (Choose two.)
- A . storage
- B . support
- C . security
- D . admin
Which NetApp tool provides information on size, weight, acoustic noise, and power of NetApp E-Series systems?
- A . Interoperability Matrix Tool
- B . Hardware Universe
- C . Active IC
- D . Config Advisor
With a system cache block size of 32K, how much cache space per I/O is “lost” if incoming I/Os are all 48K writes? (Choose the best answer.)
- A . 24K
- B . 8K
- C . 0 C no space is lost
- D . 4K
- E . 16K
In SANtricity System Manager, the Recovery Guru reports a loss of paths to an iSCSI host.
In this scenario, which tool would you use to troubleshoot this issue?
- A . PuTTY
- B . ping
- C . Device Manager
- D . telnet
If you have to replace the battery on a controller, you should put the controller into which state?
- A . quiesced
- B . service mode
- C . lockdown
- D . suspend
To discover events that need to be reported to the storage administrator, which log does the Event Monitor poll?
- A . Major Event Log
- B . ASUP log
- C . Recovery Guru log
- D . Array Profile
Your company has an E-Series system connected to Cisco MDS switches. You are asked to provision a volume on a new Windows host, but the Windows host is unable to connect to the volume on the E-Series system. All other Windows hosts in the fabric are able to connect to their volumes.
In this scenario, which three actions should you perform to accomplish this task? (Choose three.)
- A . Create a new virtual SAN (VSAN)
- B . Obtain the WWPN for the Windows HBA
- C . Restart the switches
- D . Create a single-initiator zone with the host and E-Series system
- E . Add a zone to the active zoneset
Which two actions must be performed to enable iSCSI multipathing on Windows for NetApp E-Series systems? (Choose two.)
- A . Set up iSCSI IP addresses on the E-Series system and the Windows host
- B . Install the Host Utilities on the Windows host
- C . Create two VSANs on the iSCSI switches
- D . Install a Host Channel Adapter (HCA) on the Windows host
Exhibit:
Referring to the exhibit, what would you select in the search list to see all of the host selections for NetApp ESeries storage systems?
- A . Storage OS
- B . SANtricity
- C . E-Series SAN Host
- D . E-Series Controller Firmware
Synchronous mirroring requires what type of connection between storage systems? (Choose the best answer.)
- A . FC
- B . SAS
- C . iSCSI
- D . InfiniBand
In the AMW, which tab provides access to Ethernet management port configuration and premium feature enablement? (Choose the best answer.)
- A . Storage & Copy Services
- B . Host Mappings
- C . Configuration
- D . Hardware
- E . Setup
What happens if one disk chosen for a volume group has a capacity of 2 TB and the other five disks have a capacity of 4 TB?
- A . SANtricity recognizes all disks as 2 TB.
- B . SANtricity will never allow this combination.
- C . SANtricity allows the creation of the volume group but places it offline until you add another 2-TB disk.
- D . SANtricity recognizes all disks as 4 TB.
What is the ‘base’ host connectivity provided by the E5500 Controller? (Choose the best answer.)
- A . IB
- B . SAS
- C . FC
- D . iSCSI
- E . iSCSI
What is the ‘base’ host connectivity provided by the E2600 controller? (Choose the best answer.)
- A . None
- B . IB
- C . iSCSI
- D . SAS
- E . FC
Where does the explicit multipath driver reside?
- A . on the I/O host
- B . on the storage manager host
- C . host on the storage manager client
- D . in the controller’s memory
You are helping a customer diagnose a performance issue on an E-Series storage system. You decide to measure the amount of data that is being handled over the span of an hour.
In this scenario, what are you measuring?
- A . IOPS
- B . I/O alignment
- C . parity
- D . throughput
You are setting-up asynchronous mirroring between two E2860 systems.
In this scenario, which two prerequisites are required to complete the setup? (choose two)
- A . both the primary and secondary systems must be using the same subnets for mirroring connections
- B . The secondary system must have 2X the storage capacity of the primary system
- C . Both systems must be discovered by an Enterprise Management Window (EMW) or SANtricity Unified Manager
- D . Both the primary and secondary systems must have the same premium features licensed
Where would you find the version of the driver and firmware for QLogic HBAs that are supported by NetApp E-Series systems?
- A . SANtricity Admin Guide
- B . Interoperability Matrix Tool
- C . Hardware Universe
- D . QLogic download webpage
What four resources have information to determine space and power & cooling requirements for E-Series storage systems? (Choose four.)
- A . Hardware cabling guide
- B . Install Guide
- C . Hardware Universe
- D . E-Series System Data Sheets
- E . E-Series Power & Cooling Calculator
- F . Site Prep Guide
What SANtricity package(s) must be installed on a Windows server when it is acting as both a data host and a storage management host?
- A . The client and agent
- B . The client, agent, and utilities
- C . The client, failover driver, and agent
- D . The client
What is the ‘base’ host connectivity provided by the E5400 Controller? (Choose the best answer.)
- A . None
- B . iSCSI
- C . SAS
- D . FC
- E . IB
Which item can be downloaded concurrently with controller firmware? (Choose the best answer.)
- A . SANtricity software
- B . NVSRAM
- C . ESM firmware
- D . Drive firmware
Which alerting method would be configured using the SANtricity System Manager setup wizard?
- A . Syslog
- B . SNMP
- C . Web Services Proxy
- D . Email
An administrator is asked to migrate two DE6600 shelves into a newly deployed E5760 environment that is configured with a stack of two DE460C shelves.
In this scenario, how does the administrator complete this task?
- A . Cable the DE6600s into a separate stack
- B . Cable the DE6600s between the DE460C shelves
- C . Cable the DE6600s at the beginning of the stack
- D . Cable the DE6600s at the end of the stack
A d-stripe within a disk pool is always the equivalent of _______. (Choose the best answer.)
- A . 9+1 RAID 3
- B . 9+1 RAID 5
- C . 8+2 RAID 6
- D . 5+5 RAID 10
- E . 10+0 RAID 0
What is a best practice recommendation for the automated system monitor? (Choose the best answer.)
- A . It should only run on one client connected to the storage system.
- B . It should be stopped during storage system normal operations.
- C . It should be stopped during a controller firmware upgrade.
- D . It should only be run on Windows server systems.
- E . It should run on all storage manager clients.
Exhibit:
A customer’s host is running a Red Hat Enterprise Linux 7.6 server with dm-mp configured for ALUA and is connected to a single volume on the EF280 system that is shown in the exhibit.
In this scenario, how many active/optimized paths are available to the volume?
- A . 2
- B . 8
- C . 4
- D . 6
Which component of an E-Series storage system should always be upgraded first? (Choose the best answer.)
- A . ESM firmware
- B . Controller firmware
- C . Controller NVSRAM
- D . SANtricity management client
In the storage manager client, what are host groups? (Choose the best answer.)
- A . A set of I/O hosts with access to the same set of volumes.
- B . Two or more servers that host localcache.
- C . Two or more disk devices joined together
- D . A custom group of virtual machine hosts
- E . Volumes linked to update at the same time
How many 32 Gb ports are on one FC host interface card (HIC) on the NetApp E2800, EF280, E5700, and EF570 systems?
- A . 1
- B . 2
- C . 4
- D . 6
Controller firmware package files start with which character(s)? (Choose the best answer.)
- A . SMIA
- B . CFW
- C . DLP
- D . RC
- E . N
Exhibit:
Referring to the exhibit, which cable is an InfiniBand 4X connector?
- A . 3
- B . 1
- C . 2
- D . 4
What happens if you choose one disk that has a capacity of 300 GB and five others that have a capacity of 900 GB for a volume group? (Choose the best answer.)
- A . All disks are recognized as 900 GB in capacity
- B . All disks are recognized as 900 GB in capacity
- C . Each disk is recognized as its particular capacity.
- D . Mixing disk capacities is not supported in E-Series volume groups.
Your AutoSupport does not automatically send reports to NetApp’s ActiveIQ tool.
In this scenario, how do you access the data that would have been sent using the AutoSupport feature?
- A . Use SANtricity Unified Manager to collect the support data remotely
- B . Access the event log by using SANtricity System Manager
- C . Use SANtricity System Manager to manually collect the support data
- D . Ask NetApp Support to help you to access the data by using special support tools