Network Appliance NS0-194 NetApp Certified Support Engineer Online Training
Network Appliance NS0-194 Online Training
The questions for NS0-194 were last updated at Nov 22,2024.
- Exam Code: NS0-194
- Exam Name: NetApp Certified Support Engineer
- Certification Provider: Network Appliance
- Latest update: Nov 22,2024
In ONTAP 9.6, activity on the command line is found in which log?
- A . audit.log
- B . messages.log
- C . command-history.log
- D . mgwd.log
A customer asks what is the correct way to configure an ONTAP system for multi-tenancy. The customer wants to serve data and also protect data using SnapMirror from tenant A using network A and from tenant B using network B.
In this scenario, which statement is correct?
- A . The customer must use different VLANs for the two tenants.
- B . This setup can only work if tenant A and tenant B use a shared network infrastructure.
- C . The customer must set up two different IPspaces for the two tenants.
- D . Each node can only communicate with tenant A or tenant B, but not with both at the same time.
When using NetApp Volume Encryption (NVE) which type of server is needed to keep encryption keys separate from encrypted data?
- A . KMIP
- B . RADIUS
- C . TLS
- D . TKIP
You are working on a fabric MetroCluster. After a site failure, the plex starts to resync automatically to the aggregate mirror of Aggr1. The plex now shows a status of resyncing. During this process, you experience a slow resync of the SyncMirror plex.
In this scenario, how do you solve the problem?
- A . Add more disks to the aggregate to add more I/O capacity.
- B . Destroy and re-create plex, then run a baseline sync.
- C . Tune the resync speed by adding a QoS policy and limit the concurrent I/O to the aggregate.
- D . Tune the resync speed using the storage raid-options command.
You have an ONTAP 2-node cluster. You run a read/write test workload against an SMB share, and it is slower than you expected. You run the same test again, but this time you monitor the storage using a QoS command.
Referring to the exhibit, what is the problem?
- A . There is a disk bottleneck.
- B . An HA interconnect problem is present.
- C . The SMB read sizes should be increased.
- D . The NVRAM needs to be replaced.
Which NetApp HCI component communicates with activeiq.solidfire.com and the Cloud Data Services portal?
- A . the NetApp Element software vSphere plug-in
- B . the management node (mNode)
- C . the NetApp Trident software
- D . the NetApp Element software Management Interface
You receive the error shown below on a FAS2750 HA pair.
Mon Jun 24 00:27:30 UTC [NetappA: scsi_cmdblk_strthr_admin:
scsi.cmd.checkCondition:error]: Unknown device 0a.00.99: Check Condition: CDB 0x12:
Sense Data SCSI:hardware error -(0x4 -0x44 0x0 0x0) (0).
The system is cabled as shown in the exhibit.
What should you do to clear the error?
- A . Replace the cable connected to controller A’s 0a port.
- B . Replace the controller of controller B.
- C . Replace the controller of controller A.
- D . Re-cable the system per the FAS2750 installation guide.
Which three techniques are used in ONTAP to improve storage efficiencies? (Choose three.)
- A . compression
- B . encryption
- C . compaction
- D . ADP
- E . thin provisioning
You observe cyclic redundancy check (CRC) errors on a network port from a node in the cluster.
Which two components would you consider reseating or replacing before you perform actions on the physical port where the errors are reported from the node? (Choose two.)
- A . SFP
- B . cluster interconnect switch
- C . up-stream switch
- D . cable
For security reasons, you must track the access of files of a specific folder.
In this scenario, what should you do to accomplish this task from the storage side?
- A . Implement a Vscan solution.
- B . Use a cron job to save the audit log.
- C . Use role-based access control to track access.
- D . Implement an FPolicy solution.
Latest NS0-194 Dumps Valid Version with 60 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
