Network Appliance NS0-184 NetApp Certified Storage Installation Engineer, ONTAP Online Training
Network Appliance NS0-184 Online Training
The questions for NS0-184 were last updated at Nov 23,2024.
- Exam Code: NS0-184
- Exam Name: NetApp Certified Storage Installation Engineer, ONTAP
- Certification Provider: Network Appliance
- Latest update: Nov 23,2024
You want to create a data volume on aggr0 and you receive a message with the following warning: ”Warning: You are about to create a volume on a root aggregate.
This may cause severe performance or stability problems and therefore is not recommended. Do you want to proceed?”
What is the reason for this severe performance or stability problem?
- A . Controller failover and storage failover are separate processes that must occur in parallel, otherwise problems will arise.
- B . The performance load generated by the data volume can be very strong, so it should not be shared with vol0 on aggr0, requiring a separate aggregate for it.
- C . The performance load generated by the vol0 cannot be shared with any other volume on aggr0, requiring a dedicated aggregate for it.
- D . Controller failover and storage failover are separate processes that must occur at different times, otherwise problems will arise.
You are adding new controllers to an existing cluster. As part of the upgrade process, you have updated the BES-53248 cluster switches. In this scenario.
Which two commands would you use to verify a healthy cluster after the upgrade? (Choose two.)
- A . network port show -ipspace Cluster
- B . network interface show -vserver Cluster
- C . network device-discovery show -protocol cdp
- D . network interface show -vserver Cluster -fields auto-revert
You configured AutoSupport and are trying to send a full AutoSupport message to NetApp. You use the autosupport history show command and see the output shown in the exhibit. The customer confirms that the AutoSupport settings are correct.
Which two actions will solve this issue? (Choose two.)
- A . The customer needs to enable AutoSupport for both nodes.
- B . The customer needs to exclude the two nodes from the attachment-size limitation.
- C . The customer needs to change the transport protocol to HTTP.
- D . The customer needs to white-list the two nodes on their mail server.
Upon finishing the Installation of a new system for a customer, they request that you train them on how to administer the system. In this scenario, which two responses are appropriate? (Choose two.)
- A . Visit the NetApp MySupport Site and look for the Express Guides, they will guide you through the daily tasks and provide input and output examples.
- B . If you have a specific issue, you can visit the Knowledge Base Web site (https://kb.netapp,com).
- C . The answers to any of your questions can be found on the NetApp SmartSolve site (http://smartsolve.netapp.com).
- D . You should open a case with NetApp Support for all future questions with low priority and include the keyword "Training" in the title.
After you install an AFF A700 2-node cluster with DS224C shelves, Config Advisor reports that your SAS cabling is in mixed-path HA. You expected the SAS cabling be in quad-path HA.
You physically verify the LED status on the controllers and the shelves and notice no irregularities. However, a reboot of the SAS expander does not change the output.
In this scenario, what should you do next?
- A . Open a case with NetApp Support and turn off the disk shelves until the issue is solved.
- B . Disconnect the disk shelves from the controller and run Config Advisor again.
- C . Re-seat the SAS IO modules of the affected AFF A700 controller.
- D . Use multipath HA because it is the only cabling supported on an AFF A700 controller.
Your customer wants a newly installed AFF C190 cluster to send SNMP notifications to a trap host called OVERWATCH01.
In this scenario, which two statements are correct? (Choose two.)
- A . Configure an SNMP community string on the cluster.
- B . Configure DNS on the cluster.
- C . Configure a trap host on the cluster.
- D . Configure a firewall policy and allow SNMP.
You are asked to install six shelves to a production cluster. The cluster is running clustered Data ONTAP and is a 4-node cluster. All six shelves will be cabled to the same HA pair. The customer wants you to assign all the new disks to a single node in the cluster.
Which three tools would help you accomplish this task? (Choose three.)
- A . the Hardware Universe Web-based tool
- B . the Synergy application
- C . the Config Advisor application
- D . the My AutoSupport Web-based tool
- E . the System Setup application
You were dispatched to install a cluster made up of FAS8060 and FAS8080 controllers. There are three FAS8060 controllers and three FAS8080 controllers.
Which solution would provide the largest possible cluster?
- A . a cluster made up of two nodes
- B . a cluster made up of four nodes
- C . a cluster made up of five nodes
- D . a cluster made up of six nodes
What is the minimum number of disks required in a SAS shelf?
- A . half of the shelf’s capacity
- B . one
- C . two
- D . there is no minimum
A host cannot connect to the namespace configured on an NVMe-enabled SVM.
In this scenario, what are two reasons for this problem? (Choose two.)
- A . The namespace has not been added to the subsystem
- B . The namespace has not be added to the igroup
- C . The igroup has an incorrect NQN.
- D . The subsystem has an incorrect NQN
Latest NS0-184 Dumps Valid Version with 60 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
