You currently have an 8-node cluster and want to perform a rolling upgrade to a newer version of ONTAP to solve security issues reported in the Active IQ Web site.
In this scenario, which two steps should you validate before you perform the upgrade? (Choose two.)
- A . Run Active IQ Config Advisor.
- B . Validate Nodes with Hardware Universe.
- C . Validate Nodes with Active IQ Unified Manager.
- D . Run Upgrade Advisor Report.
When performing a manual MetroCluster switchover, which two statements are true? (Choose two.)
- A . Only the user specified DR groups are switched over.
- B . All SVMs in the disaster site are switched over.
- C . All DR groups in the disaster site are switched over.
- D . Only the user specified SVMs are switched over.
Click the Exhibit button.
A volume is only 25% full; however, the snapshot reserve is almost full.
Referring to the exhibit, what occurs after the volume’s snapshot reserve is full?
- A . User-created Snapshot copies are deleted, beginning with the oldest, until the snapshot reserve has 20% free space.
- B . Scheduled Snapshot copies are deleted, beginning with the oldest, until the snapshot reserve has 20% free space.
- C . Snapshot copies start consuming the volume’s free space.
- D . The creation of new Snapshot copies fails.
Which two statements about replicating FlexGroup volumes are true? (Choose two.)
- A . You can increase the capacity of a FlexGroup volume that is being replicated.
- B . The SnapMirror relationship type must be XDP.
- C . You cannot perform a resync on a FlexGroup SnapMirror relationship after it has been broken.
- D . The SnapMirror relationship type must be DP.
What are two advantages of creating small RAID groups inside an aggregate? (Choose two.)
- A . maximized storage space
- B . decreased risk of multiple disk failure
- C . shorter reconstruction time
- D . additional available spare drives
Click the Exhibit button.
While troubleshooting performance issues, you notice that only one port in the NetApp interface group a0a is actively sending or receiving data.
Referring to the exhibit, what should you do to ensure that both ports in the interface group are actively used?
- A . Change the interface group mode to multimode_lacp.
- B . Verify that the network switch has flow-control enabled.
- C . Verify that the physical cabling is properly connected to ensure a network link.
- D . Change the distribution function to ip.
When a write from a SAN host is received, the information is stored within the controller before it is written to the underlying RAID.
In this scenario, which component stores the data?
- A . NVRAM
- B . Flash Pool
- C . HBA
- D . FlashCache
Which two features are supported on NetApp ONTAP? (Choose two.)
- A . SnapMirror
- B . FlexCache
- C . Fibre Channel
- D . Storage Pool
You created a new SVM with two NFS data volumes. You have a Linux host on the same subnet as the SVM that is able to NFS mount, however a Linux host on a different subnet is not able to NFS mount.
You confirmed that the export policy rules are correct.
In this scenario, which configuration will solve the mount failure? (Choose the best answer.)
- A . The NFS server is not configured on the SVM.
- B . NTP is not configured on the SVM.
- C . NFS auditing is not enabled on the SVM.
- D . The SVM default network route is missing.
Which ONTAP feature uses the Service Processor to speed up takeover times between HA pairs?
- A . hardware-assisted takeover
- B . automatic takeover and giveback
- C . epsilon
- D . cluster HA
Node A has taken over Node B. You solved the issue that caused the takeover and are now ready to resume normal operation.
After initiating the storage failover giveback command, how are the aggregates given back? (Choose the best answer.)
- A . CFO aggregates are automatically given back, SFO aggregates must be manually given back.
- B . CFO aggregates and SFO aggregates are automatically given back.
- C . The root aggregate is automatically given back, CFO and SFO aggregates must be manually given back.
- D . SFO aggregates are automatically given back, CFO aggregates must be manually given back.
You need to move a FlexVol volume from one SVM to another.
In this situation, which command would accomplish this task?
- A . volume create
- B . volume rehost
- C . volume modify
- D . volume move
Which three name services are supported with NFS? (Choose three.)
- A . NetBIOS
- B . WINS
- C . External NIS domains (NIS)
- D . External LDAP domains (LDAP)
- E . Local Users (file)
On your customer’s AFF A700, there are multiple volumes within the aggregate aggr1. Within aggr1, volumes vol1, vol2, and vol3 store similar data, and volumes vol4 and vol5 store unique data.
In this scenario, which feature would improve storage efficiency with the data stored in volumes vol1, vol2, and vol3?
- A . postprocess compression
- B . data compaction
- C . inline aggregate-level deduplication
- D . inline compression
Which three steps are required to serve NFS exports from your ONTAP system? (Choose three.)
- A . You must create an export policy rule.
- B . You must license CIFS.
- C . You must create an SMB share.
- D . You must license NFS.
- E . You must have provisioned a volume to export.
Exhibit:
You have a 2-node ONTAP cluster with both 0e ports connected to Fabric A.
You have an FC host connected to the FC fabric with the following initiator WWNs:
– WWNN: 20:00:00:25:B5:01:F0:2A
– WWPN Fabric A: 20:00:00:25:B5:01:A0:2A
Referring to the exhibit, which three WWNs should be configured in a zone together? (Choose three.)
- A . 20:0d:00:a0:98:69:97:ff
- B . 20:00:00:25:B5:01:F0:2A
- C . 20:0f:00:a0:98:69:97:ff
- D . 50:0a:09:82:80:01:b7:1b
- E . 20:00:00:25:B5:01:A0:2A
An administrator is designing an ONTAP solution that consists of eight FAS8200 nodes in a single cluster. Each node will use four ports for cluster connections.
Which cluster interconnect switch model should be used in this scenario?
- A . Nexus 5596UP
- B . Nexus 5010
- C . CN1610
- D . CN1601
Which two statements are true when you restore a volume from a Snapshot copy? (Choose two.)
- A . All Snapshot copies that were created after the Snapshot copy was created are lost.
- B . All data that was written to the volume after the Snapshot copy was created is lost.
- C . The volume’s SnapMirror relationships need to be re-created.
- D . After the volume is restored, it becomes read-only.
Exhibit:
You execute the cluster1::> network ipspace showcommand, and notice that two IPspaces are not able to be renamed or deleted.
Referring to the exhibit, what are these two IPspaces? (Choose two.)
- A . IPspace2
- B . Default
- C . IPspace1
- D . Cluster
An SVM is configured to authenticate SVM administrators with the access method set to Password. A computer account for the SVM exists on the Active Directory domain controller. You are now required to authenticate administrators trough domain.
Which two steps are required to accomplish this task? (Choose two.)
- A . Re-create the computer account for the SVM on the domain.
- B . Configure the SVM as a tunnel to the domain.
- C . Create a custom role for all users who belong to the domain
- D . Create a login account on the cluster for the domain users with an access method of ‘domain’
In which scenario would you specifically assign aggregates to SVMs?
- A . to configure an ONTAP system for CIFS and iSCSI
- B . to create SnapMirror peering relationships between SVMs
- C . to prevent a storage administrator from overcommitting an aggregate
- D . to configure an ONTAP system for multi-tenancy
A storage administrator currently has an 8-node FAS8200 cluster with CIFS, NFS, and iSCSI licenses installed. In this scenario, how many additional nodes are supported?
- A . 3
- B . 6
- C . 4
- D . 1
An administrator has an SVM named SVM_NAS that is used for NFS clients. You change the volume junction path of a volume named vol1 from /vol1 to /IT/vol1. After you make this change, the existing NFS clients are unable to connect to the new path.
Which cluster object should you update to solve this problem?
- A . the load-sharing mirror of the SVM root volume
- B . the cluster admin LIF
- C . the data LIF on the SVM_NAS SVM
- D . the export policy on the SVM_NAS SVM
You want to improve the write performance of NL-SAS volumes serving data on your ONTAP. You also want to keep the performance consistent during a possible controller failover.
In this scenario, which feature do you use? (Choose the best answer.)
- A . Flash Cache
- B . Flash Pool
- C . FlexCache
- D . FabricPool
You must expand an existing FAS8200 switchless cluster to a switched cluster and add a new FAS8200 HA pair in the cluster.
In this scenario, which three actions would you perform to expand the cluster? (Choose three.)
- A . Ensure that the switchless-cluster network option is false.
- B . Connect the existing nodes to the cluster switches.
- C . Change the cluster ports for the existing HA pair.
- D . Ensure that the switchless-cluster network option is true.
- E . Join the new HA pair to the cluster.
Which block protocol does ONTAP Cloud support?
- A . iSCSI
- B . FCoE
- C . CIFS
- D . NFS
When FCOE is used in a cluster, which feature must be licensed?
- A . CIFS
- B . NFS
- C . iSCS1
- D . FCP
You are training a storage operator to view the aggregates available on the nodes from multiple shells.
Which two shell and command combinations would you use to accomplish this task? (Choose two.)
- A . nodeshell aggregate status
- B . systemshell aggregate status
- C . systemshell aggregate show
- D . clustershell aggregate show
Which type of write once, read many (WORM) workload is designed for compliance purposes through SnapLock?
- A . WORM files on MetroCluster volumes
- B . WORM files on SyncMirror aggregates
- C . WORM files using SnapMirror replication
- D . WORM files on FlexArray aggregates
Your company has recently decided to stop using the Fibre Channel Protocol (FCP) in the data center. You are asked to decommission FCP and reuse any UTA2 ports to 10 GbE.
Which two steps are involved in this task? (Choose two.)
- A . Reboot the nodes.
- B . Destroy any FC LIFs hosted on UTA2 ports.
- C . Remove the FCP license from all nodes in the cluster.
- D . License additional phttps://www.netapp.com/pdf.html?item=/media/13482-tr4375pdf.pdforts for 10 GbE connectivity.
An administrator wants to segment applications based on performance. The applications are all using LUNs to access their data.
In this scenario, what are two methods of using quality of service (QoS) to improve performance? (Choose two.)
- A . Set the policy group for the SVM that is hosting the LUNs.
- B . Set the policy group for the volumes that are hosting the LUNs.
- C . Set the policy group for the initiator groups (igroups) mapped to the LUNs.
- D . Set the policy group for the FC target ports that are being used for the LUNs.
You execute the volume unmount -vserver vsl -volume vol1 command.
In this scenario, which statement is true?
- A . Data within the vol1 volume is lost.
- B . All data within the junction point is inaccessible to NAS clients.
- C . The Snapshot policy in the volume needs to be recreated once the volume is remounted.
- D . The existing volume export policies and SMB shares created on the volume or on directories and junction points within the unmounted volume are not retained.
Which configuration is supported by MetroCluster?
- A . a single AFF at Site A attached through fabrics to an AFF HA pair at Site B
- B . an AFF HA pair at Site A attached through fabrics to a FAS HA pair at Site B
- C . a single AFF at Site A attached directly to a single AFF at Site B
- D . an HA pair at Site A attached directly to an HA pair at Site B
An administrator wants to restore a file using the Previous Versions tab on a Windows client.
Which command enables the Previous Versions feature?
- A . volume modify -group
- B . volume modify -user
- C . volume modify -policy
- D . volume modify -snapdir-access
Exhibit:
An administrator needs to configure ports for peering.
Referring to the exhibit, which ports should be used?
- A . CDOT93-01:e0a and CDOT93-02:e0a
- B . CDOT93-01:e0e and CDOT93-02:e0e
- C . CDOT93-01:e0d and CDOT93-02:e0d
- D . CDOT93-01:e0f and CDOT93-02:e0f
When a storage QoS policy is configured, which two metrics are configured with a maximum limit? (Choose two.)
- A . concurrent connections
- B . IOPS
- C . MBps
- D . latency
Which command would you use to enable the ONTAP HA feature?
- A . storage failover modify -enabled true -node *
- B . cluster ha modify -configured true
- C . cluster ha modify Cconfigured false
- D . network options switchless-cluster modify true
How would you protect a NAS SVM root volume?
- A . Create a SnapMirror copy of the root volume to a peer cluster.
- B . Create load-sharing mirrors.
- C . Create a backup the SVM configuration.
- D . Create a backup of the SVM root volume.
You have Windows Server 2019 hosts that use network address translation (NAT) on the network when connecting to their ONTAP 9.8 AFF A400 cluster. You are having iSCSI connectivity issues using IP addresses. The network team recommends using fully qualified domain names (FQDNs).
Which SAN setting in ONTAP would you modify in this scenario?
- A . LIF service policies
- B . Selective LUN Map (SLM)
- C . SendTargets
- D . port sets
Click the Exhibit button.
You have a mission-critical SQL application that uses a single SMB 3.1.1 share to host its database. The storage node that is hosting the SMB share sql01_ca for the SQL database experiences a hardware failure and fails over to the surviving node.
Referring to the exhibit, what is the state of the SMB share for the SQL database during the failover? (Choose the best answer.)
- A . The SMB share will be available, but all data is corrupted.
- B . The SMB share will be unavailable until node failback.
- C . The SMB share will be available, and all data is accessible.
- D . The SMB share is unavailable due to its stateful nature.
Which commands shows the data compaction savings for an aggregate?
- A . storage aggregate show-space
- B . storage aggregate show-efficiency
- C . volume efficiency show
- D . storage efficiency show
Exhibit:
Referring to the exhibit, a customer is experiencing performance problems on an SVM supporting NVMe/FC. You review the physical FC ports that are connected into the 32 Gbps switches for cluster tme-a700.
In this scenario, what is causing the performance problems? (Choose the best answer.)
- A . Port 2a needs more network interfaces added to the physical port.
- B . Port 2b has a 16 Gbps SFP+ installed.
- C . Port 2a needs a 16 Gbps SFP+ installed.
- D . Port 2b has two many LIFs running across the physical port.
Exhibit:
A storage administrator has an existing FAS2554 HA pair. They want to add a new FAS2620 HA pair to the cluster. The SAN protocols are licensed.
Referring to the exhibit, after adding the second HA pair, how many more nodes are available to add for future use?
- A . 4
- B . 8
- C . 2
- D . 12
Which two components are required for committing data to a WORM volume? (Choose two.)
- A . You must license SnapLock.
- B . You must create a SnapLock volume.
- C . You must create a SnapLock SVM.
- D . You must create a SnapLock Aggregate.
Exhibit:
Your manager asks you to create a new FlexVol on an aggregate called AGGR_2. When you click "Create new FlexVol", you are unable to select AGGR_2 to create the new volume.
Referring to the exhibit, which two SVM settings solve this problem? (Choose two.)
- A . In the resource allocation tab, select the "Delegate volume creation" option and select AGGR_2.
- B . Use the volume move option and reallocate the SVMs root volume to AGGR_2.
- C . In the resource allocation tab, select the "Do not delegate volume creation" option.
- D . Change the aggregate security style of AGGR_2 to UNIX.
You change a volume’s space guarantee from volume to none.
In this scenario, which statement is correct?
- A . Free space from the volume shows up as free space in the aggregate.
- B . All existing snapshots are automatically deleted.
- C . Snap reserve is set to zero (0).
- D . Fractional reserve is set to zero (0).
Exhibit:
A storage administrator is unable to mount NFS volumes in the SVM1 namespace.
Referring to the exhibit, what is causing this problem?
- A . The NFS v4 ACL support is disabled
- B . The NFS protocol is disabled
- C . The NFS license is disabled
- D . The NFS v3 and v4 protocols are running at the same time.
Exhibit:
The maximum RAID group size of the RAID-DP aggr1 shown in the exhibit is 18. You expand the aggregate by 20 disks.
How many of the new disks are used for data?
- A . 20
- B . 16
- C . 14
- D . 18
You are provisioning a LUN for a new host.
In this scenario, which three objects must exist? (Choose three.)
- A . export policy
- B . igroup
- C . LUN
- D . interface group
- E . volume
Which NetApp cluster configuration requires the use of epsilon?
- A . a singe-node cluster
- B . a cluster with an odd number of nodes
- C . a 2-node cluster
- D . a 4-node cluster
Which three configurations does ONTAP Select support? (Choose three.)
- A . 2-node cluster hosting NAS and iSCSI
- B . 3-node cluster hosting NAS and iSCSI
- C . single-node cluster hosting NAS and iSCSI
- D . 4-node cluster hosting NAS and iSCSI
- E . 6-node cluster hosting NAS and iSCSI
What are three types of licenses available for ONTAP? (Choose three.)
- A . standard
- B . evaluation
- C . system
- D . site
- E . field
An administrator is configuring a third-party software for NDMP. The application is targeting the IP of the data LIF of the SVM called "SVM1. "NDMP is configured as the SVM scope.
The NDMP service is not enabled for the admin SVM. SVM1 has a user called "Tom" with the backup role. Tom can connect by using SSH to the controller with the credentials that he used to configure the third-party software. The authentication of the third-party software is falling.
In this scenario, what is the reason for the authentication failure?
- A . The NDMP password has not been generated for Tom.
- B . The application is not targeting the IP of the cluster or node management LIF.
- C . The user Tom does not belong to the admin SVM.
- D . The NDMP service is not enabled for the admin SVM.
You want to use UTA2 ports for native FC LUN access.
How do you accomplish this task?
- A . Configure the UTA2 ports as target ports with 16 Gb SFP+ transceivers.
- B . Configure the UTA2 ports as target ports with 10 Gb SFP+ transceivers
- C . Configure the UTA2 ports as initiator ports with 10 Gb SFP+ transceivers
- D . Configure the UTA2 ports as initiator ports with 16 Gb SFP+ transceivers
Which two types of HA policies are applied to which types of aggregates? (Choose two.)
- A . storage failover (SFO) policy to data aggregates only
- B . controller failover (CFO) policy to all the aggregates
- C . storage failover (SFO) policy to root aggregates only
- D . controller failover (CFO) policy to root aggregates
When you create a FlexVol volume, which security style is applied by default?
- A . the security style of the SVM root volume
- B . the security style of the root volume of the cluster
- C . NTFS
- D . UNIX
An administrator is configuring an aggregate to use FabricPool to take advantage of auto tiering.
In this scenario, what are three requirements to accomplish this task? (Choose three.)
- A . volume with space-guarantee none
- B . FabricPool license
- C . intercluster LIFs
- D . volume with space-guarantee volume
- E . AFF array
Which three name services does ONTAP support? (Choose three.)
- A . HTTP
- B . local files
- C . LDAP
- D . NIS
- E . SNMP
Which NetApp software do you use to confirm that the SAS cabling is correct?
- A . Hardware Universe
- B . Active IQ Config Advisor
- C . Interoperability Matrix Tool
- D . Active IQ Unifide manager
You have a mix of FAS8200s and AFF A700s in your environment. In this scenario, which two statements are true? (Choose two.)
- A . Inline data compaction is disabled by default on FAS systems.
- B . Inline aggregate-level deduplication is enabled by default on FAS systems.
- C . Inline data compaction is disabled by default on AFF systems.
- D . Inline aggregate-level deduplication is enabled by default on AFF systems.
Which mediator type is required for an ONTAP Select 2-node HA solution?
- A . mediator code
- B . mediator storage virtual machine
- C . mediator cluster
- D . mediator virtual machine
Click the Exhibit button.
Assuming that the export policy on the storage allows access, you want to enable client access to the finance volume in the departments SVM in the /tmp/fin directory.
Referring to the exhibit, which UNIX command must be executed to accomplish this task?
- A . mount Ct nfs Co nfsvers=3 cluster01:/finance /tmp/fin
- B . mount Ct nfs Co nfsvers=3 cluster01:/fin /tmp/fin
- C . mount Ct nfs Co nfsvers=3 cluster01:/dept/fin /tmp/fin
- D . mount Ct nfs Co nfsvers=3 cluster01:/departments/finance /tmp/fin
Which two statements are true about epsilon? (Choose two.)
- A . Epsilon is automatically assigned to the last node when the cluster is created.
- B . Epsilon is an extra fractional vote that enables quorum.
- C . In a two-node cluster, each node holds epsilon.
- D . Epsilon is automatically assigned to the first node when the cluster is created.
A storage administrator moves a LUN from one volume to another.
In this scenario, what is left behind in the volume?
- A . LUN geometry settings
- B . all of the deduplicated blocks from the base LUN
- C . Snapshot copies of the volume
- D . clones of the LUN
Exhibit:
An export policy rule for a volume is set by using the command shown in the exhibit.
If clients with IP addresses 10.64.19.0 and 10.64.18.20 accessed the export, what is the outcome?
- A . Neither client is given access.
- B . Client 10.64.19.0 is given access but 10.64.18.20 is not given access.
- C . Client 10.64.19.0 is not given access but 10.64.18.20 is given access.
- D . Both clients are given access.
Your company requires that all data must be encrypted in flight to prevent data from falling into the wrong hands.
What are two ways to accomplish this task? (Choose two.)
- A . Ensure that SnapMirror compression is enabled in all SnapMirror relationships.
- B . Modify your cluster peering relationships to support cluster peering encryption.
- C . Enable Multi-Factor Authentication (MFA) for your SnapMirror relationships.
- D . Ensure that all intercluster replication traffic is done through a VPN tunnel.
On which two types of ports would data LIFs be hosted? (Choose two.)
- A . physical ports or interface groups that host VLANs
- B . management e0M port
- C . console RJ45 port
- D . physical ports that are not part of interface groups
You are an administrator that manages a number of mission-critical applications that use block protocols only. The business unit requires the fastest storage failover.
In this scenario, which ONTAP solution satisfies the requirement?
- A . All SAN Array (ASA) with symmetric active-active topology
- B . ONTAP Select with Asymmetric Logical Unit Access (ALUA)
- C . AFF with Asymmetric Logical Unit Access (ALUA)
- D . FAS with symmetric active-active topology
You relocate an aggregate to a different node by using the storage aggregate relocate command.
In this scenario, which rule applies?
- A . You cannot relocate an aggregate that is hosting a FlexGroup constituent volume.
- B . You can only relocate an aggregate to the HA partner node.
- C . You can only relocate an aggregate that is not assigned to a specific SVM.
- D . You must first break the relationship to move an aggregate that hosts a replication destination.
Which three statements are true for mailbox disks per node in an HA pair? (Choose three.)
- A . Six disks are required if the root volume is on a mirrored aggregate.
- B . Two disks are required if the root volume is on a disk shelf.
- C . Four disks are required if the root volume is on a mirrored aggregate.
- D . Eight disks are required if the root volume is on partitioned disks.
- E . One array LUN is required if the root volume is on a storage array.
What is the purpose of Epsilon?
- A . to monitor cluster health
- B . to be used as a load-balancer for a 2-node cluster
- C . to evaluate the differences in node configurations
- D . to be used as a tie-breaker for a cluster quorum
Which two licensed protocols are assigned to an SVM for block protocols? (Choose two.)
- A . FCoE
- B . FCP
- C . CIFS
- D . iSCSI
To configure high availability within a FAS8080 EX HA pair, which two statements are correct? (Choose two.)
- A . Connect the NVRAM HA interconnects between the nodes in the HA pair.
- B . Cable the cluster interconnects to the interconnect switch.
- C . Connect multiple FC paths from the controllers to the hosts.
- D . Connect both the local node and partner node to disk shelves using multipath HA.
You are the administrator of your company’s ONTAP 9.7 storage system. Your system hosted CIFS shares in your Active Directory environment for several years without any problems.
Suddenly users report to you that they can no longer access their CIFS shares.
What is the reason for this problem? (Choose the best answer.)
- A . The CIFS standard license expired.
- B . The user account used to join your SMB server to your Active Directory expired.
- C . The WINS servers are unreachable.
- D . The NTP servers are unreachable.
Click the Exhibit button.
Referring to the exhibit, what is a valid storage failover scenario?
- A . Node 1 fails and Node 2 takes over Node 1’s storage.
- B . Node 4 fails and Node 2 takes over Node 4’s storage
- C . Node 3 fails and Node 1 takes over Node 3’s storage.
- D . Node 2 fails and Node 3 takes over Node 2’s storage.
Click the Exhibit button.
Your 4-node cluster has two controllers in takeover as shown in the exhibit.
Which action must be performed to ensure a giveback occurs on both nodes?
- A . Perform a giveback of node4.
- B . Perform a giveback of node3.
- C . Perform a giveback of node2.
- D . Perform a giveback of node1.
Which two objects are supported in a FlexVol volume? (Choose two.)
- A . aggregate
- B . qtree
- C . RAID group
- D . LUN
Exhibit:
You are working on a disaster recovery situation where the controller, which is part of a fabric-attached MetroCluster configuration in the disaster site, fails to boot and stays at the loader prompt. This failure generates the error message that is shown in the exhibit.
Which sequence of steps will recover the disaster site?
- A . Perform switchback, heal data aggregate, heal root aggregate, and boot ONTAP.
- B . Heal root aggregate, heal data aggregate, boot ONTAP, and perform switchback.
- C . Heal data aggregate, heal root aggregate, boot ONTAP, and perform switchback.
- D . Boot ONTAP, heal root aggregate, heal data aggregate, and perform switchback.
Exhibit:
Referring to the exhibit, what are two reasons why no initiators are displayed in the initiators’ igroup screen? (Choose two.)
- A . The server has not been powered up.
- B . SLM has not been enabled.
- C . Zoning on the switches has been done incorrectly.
- D . ALUA has not been enabled on the NetApp controllers.
You have a FAS8200 serving a dataset with a high volume of random reads. The dataset is highly optimized by deduplication and compression.
In this scenario, which compression setting provides both high performance and storage efficiency? (Choose the best answer.)
- A . compression disabled
- B . aggregate compression
- C . secondary compression
- D . adaptive compression
Exhibit:
Referring to the exhibit, which connections are used for the cluster interconnect LIFs?
- A . 1
- B . 2
- C . 3A
- D . 3B
You are setting up replication between two clusters.
In this scenario, which two components are required to set up the cluster peering? (Choose two.)
- A . DNS service on each cluster.
- B . An intercluster LIF on only the epsilon node.
- C . ICMP service between clusters.
- D . An intercluster LIF on every node.
When a cluster is created, which two objects are required to provide management access? (Choose two.)
- A . data LIFs
- B . management LIFs
- C . data SVM
- D . admin SVM
An administrator notices that the applications are running slowly. The administrator wants to determine which component on the ONTAP subsystem is experiencing the most latency.
In this scenario, which command would you use to accomplish this task?
- A . run -node * stats show system::sys_avg_latency
- B . statistics system show
- C . run -node * -command sysstat -x 1
- D . qos statistics latency show
Exhibit:
You have a FAS8200 HA pair with disks that are evenly split between nodes A and B. When a disk fails, the replacement disk must automatically assign back to the originally assigned controller, A or B.
Referring to the exhibit, which disk auto assign policy satisfies this requirement?
- A . stack
- B . bay
- C . default
- D . shelf
Your ONTAP cluster serves data and backup traffic running on the same physical port. You must isolate backup traffic from your production network traffic.
Which two actions must be performed to accomplish this task? (Choose two.)
- A . Create a namespace.
- B . Create a VLAN.
- C . Create a broadcast domain.
- D . Create IPspaces.
At which level of granularity would you back up data to tape using the SMTape command?
- A . directory
- B . qtree
- C . volume
- D . aggregate
You have a RAID-DP aggregate with 42x 4 TB NL-SAS drives. The aggregate contains 3x RAID groups of 14 drives each (12 data + 2 parity), for a total of 36 data and 6 parity drives.
You decide to convert the aggregate to RAID-TEC for higher resiliency.
How many spare 4 TB drives are needed to complete the conversion?
- A . 1
- B . 2
- C . 4
- D . 3
Which failover policy is set by default on an iSCSI LIF?
- A . local-only
- B . broadcast-domain-wide
- C . disabled
- D . sfo-partner-only
Click the Exhibit button.
You have a 4-node NetApp SAN cluster configured as shown in the exhibit.
By default, how many LUN paths does the host see for a newly created LUN on Node 01?
- A . 2
- B . 1
- C . 8
- D . 4
Which three data protocols are supported simultaneously in a single storage virtual machine (SVM)? (Choose three.)
- A . FCP
- B . iSCSI
- C . HTTP
- D . CIFS
- E . InfiniBand
You have an AFF A300 2-node cluster and are adding a FAS8200 to this cluster for additional storage capacity. You want to move a volume to one of the FAS8200 nodes.
Which ONTAP command is used to accomplish this task?
- A . volume aggr vacate
- B . volume rehost
- C . volume move
- D . aggr relocate
You have a test SVM named svm1 with a LIF that needs to reach a DNS server on a different Layer 2 network. The default route for each network ends in .1 and both networks route to each other.
Referring to the network command output shown in the exhibit, which command will allow access from svm1 to lab.local DNS?
- A . network route create -vserver svml -destination 192.168.0.0/24 -gateway 192.168.2.1 -metric 20
- B . network route create -vserver svml -destination 0.0.0.0/0 -gateway 192.168.2.1 -metric 20
- C . network route create -vserver svml -destination 0.0.0.0/0 -gateway 192.168.0.1 -metric 20
- D . network route create -vserver svml -destination 192.168.0.0/24 -gateway 192.168.0.1 -metric 20
Click the Exhibit button.
The exhibit displays the values for the default adaptive QoS policy. An administrator assigns the Value policy to a 1 TB volume. Over time, the volume expands to 3 TB.
What is the peak IOPS for the volume, both before and after the expansion? (Choose the best answer.)
- A . 512 IOPS and 512 IOPS
- B . 512 IOPS and 1536 IOPS
- C . 512 IOPS and 12288 IOPS
- D . 75 IOPS and 512 IOPS
You want to prevent a single file from filling up a single constituent in a FlexGroup.
Which FlexGroup feature in ONTAP 9.7 will accomplish this task? (Choose the best answer.)
- A . Flash Pool
- B . fractional reserve
- C . Snapshot autodelete
- D . elastic sizing
A customer has lost access to shares being used by an application.
What are three troubleshooting steps the administrator should take? (Choose three.)
- A . Verify that the admin SVM is running on the node being accessed by the customer.
- B . Verify that the LIF resides on its home port.
- C . Verify that the LIFs in the SVM are all up and active.
- D . Verify that the SVM has CIFS running, that the share exists, and is online.
- E . Verify that there is network connectivity between the SMB client and the SVM.
Exhibit:
You need to create a 200 GB volume that requires 700 IOPS.
Referring to the exhibit, in which aggregate should you create the volume?
- A . aggr1_01
- B . aggr2_02
- C . aggr1_02
- D . aggr2_01
A customer wants to add nodes to an 8-node AFF A700 NAS cluster.
In this scenario, what is the maximum number of additional nodes?
- A . 8
- B . 16
- C . 24
- D . 12
Regarding root partitioned disks in an ONTAP system, which three types of objects are associated with ADP? (Choose three.)
- A . root partition
- B . array LUN
- C . data partition
- D . shared disk
- E . container disk
Exhibit:
cluster1::> volume create -vserver vsl -volume voll -aggregate aggr1 -encrypt true
Which statement regarding the command shown in the exhibit is true?
- A . The volume will be created and protected on an aggregate using NetApp Storage Encryption (NSE) disks.
- B . The volume will be created and protected using an external Key Management Server.
- C . The volume will be created and protected for Snaplock Enterprise compliance.
- D . The volume will be created and protected using NetApp Volume Encryption (NVE).