Juniper JN0-682 Data Center, Professional (JNCIP-DC) Online Training
Juniper JN0-682 Online Training
The questions for JN0-682 were last updated at Dec 26,2024.
- Exam Code: JN0-682
- Exam Name: Data Center, Professional (JNCIP-DC)
- Certification Provider: Juniper
- Latest update: Dec 26,2024
You are asked to scale the available bandwidth within your Clos data center network to support more east-west traffic.
In this scenario, what are two ways to accomplish this task? (Choose two.)
- A . Add leaf devices to increase available paths and bandwidth
- B . Use aggregated interfaces in the fabric.
- C . Add spines to increase available paths and bandwidth.
- D . Interconnect all spines to increase available paths and bandwidth.
Which two statements are correct about a spine and leaf-based IP fabric? (Choose two.)
- A . Traffic is diverted within the fabric when a device or link fails.
- B . There is no need for redundancy at the server level.
- C . Leaf switches broadcast frames to all other leaf devices.
- D . Clos networks demonstrate good scaling features.
You are troubleshooting a traditional Clos Layer 3 IP fabric in your data center.
You are reviewing the BGP configuration for one of your spine devices.
Referring to the exhibit, which statement is correct?
- A . This spine device will not install multiple next hops for remote destinations in its routing table.
- B . This spine device will not install any routes for remote destinations in its routing table.
- C . This spine device has three neighboring leaf devices.
- D . This spine device has three neighboring spine devices.
Referring to the exhibit, which statement is correct?
- A . Leaf1 has not learned any MAC addresses
- B . Leaf3 is the remote tunnel endpoint.
- C . One tunnel is servicing multiple VLANs
- D . Spanning Tree Protocol is disabled
You are asked to deploy an Ethernet bridging design in a data center with the criteria shown below.
– Routing must occur on the spine devices.
– VTEPs must terminate on the leaf devices.
– Facilitate inter-VLAN communication.
– Layer 2 gateways must be present on spine and leaf devices.
Which architecture should you use in this scenario?
- A . edge-routed bridging architecture
- B . centrally-routed bridging architecture
- C . bridge overlay architecture
- D . collapsed spine architecture
The two data centers shown in the exhibit need to be connected using EVPN.
Which two statements are correct in this situation? (Choose two.)
- A . Hosts in VLAN 10 can communicate with hosts in Data Center 2 using Layer 3.
- B . Hosts in VLAN 10 can communicate with hosts in Data Center 2 using Layer 2.
- C . Hosts in VLAN 202 can communicate using Layer 3 between data centers.
- D . Hosts in VLAN 202 can communicate using Layer 2 between data centers.
What is an advantage that EVPN has over VPLS when used for DCI?
- A . mass MAC withdrawal
- B . transparent BPDU transport
- C . active/standby multihoming
- D . reverse path forwarding
You are asked to enable visibility into your EVPN-VXLAN network traffic by monitoring traffic continuously.
Which two statements are correct in this scenario? (Choose two.)
- A . You cannot enable sFlow monitoring on each interface individually.
- B . The sFlow agent is installed by default on your OFX Series switch.
- C . You must enable sFlow monitoring on each interface individually.
- D . The sFlow agent needs to be manually installed on your QFX Series switch.
You are troubleshooting a problem with traffic not reaching a remote VTEP.
Referring to the exhibit, what is the reason for the problem?
- A . A conflict exists with the VLAN-to-VNI mapping.
- B . The local VTEP is misconfigured with the wrong VNI.
- C . No VTEP is configured on peer 192.0.2.20.
- D . The remote VTEP does not have the correct VNI configured.
The configuration shown in the exhibit is intended to set up assisted replication but will not commit.
Which action will create a valid configuration in this situation?
- A . Change the 10.0 address to 192.168.100.1 primary.
- B . Change the replicator inet address to 192.168.100.101.
- C . Delete replicator inet 192.168.100.1.
- D . Change the replicator inet address to 192.168.100. 51.
Latest JN0-682 Dumps Valid Version with 65 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
