Juniper JN0-663 Service Provider Routing and Switching, Professional (JNCIP-SP) Online Training
Juniper JN0-663 Online Training
The questions for JN0-663 were last updated at Dec 25,2024.
- Exam Code: JN0-663
- Exam Name: Service Provider Routing and Switching, Professional (JNCIP-SP)
- Certification Provider: Juniper
- Latest update: Dec 25,2024
What information is stored in a VRF table for a BGP Layer 2 VPN? (Choose three.)
- A . Layer 2 encapsulation B. local site ID C. remote interface of local CE device D. logical interlace provisioned to local CE device E. label-switched path
You want to allow the load balancing of traffic for an EBGP route from two different peers in the same AS.
Which three actions are needed to accomplish this task? (Choose three.)
- A . A policy to load-balance traffic should be applied to the forwarding table
- B . At least two interfaces should be connected to the same EBGP neighbor
- C . The multihop parameter should be configured under protocols BGP
- D . The multipath parameter should be configured under protocols BGP
- E . An equal cost AS path for the route is required.
Exhibit.
Two CE devices (CE-1 and CE-2) belong to the same customer and connect into a single PE device (PE-1) However, the CE devices cannot communicate with each other. You want to allow the CE devices to communicate with each other.
Referring to the exhibit, which action would solve the problem?
- A . Configure both routing instances with the set routing-opt ions auto-export-statement
- B . Configure both routing instances with the set routing-options autonomous-system loops 3 statement
- C . Configure both routing instances with the vrf-table-label statement
- D . Configure both routing instances with the as-override statement within the BGP protocol
Exhibit: Referring to the exhibit, the local BGP router is receiving IPv4 routes from the BGP neighbor, but it is not receiving L3 VPN routes from the BGP neighbor.
Which two actions should you take to solve this problem? (Choose two.)
- A . Configure the family inet-vpn unicast statement on the local BGP router.
- B . Configure the family inet unicast statement on the local BGP router.
- C . Configure the family inet unicast statement on the BGP neighbor
- D . Configure the family inet-vpn unicast statement on the BGP neighbor.
What is the purpose of the duster-list attribute within a BGP route reflector group?
- A . to disable internal cluster re-advertisements
- B . to define the router that first advertised the route to the route reflector
- C . to override the router 10 value within the cluster
- D . to facilitate loop detection within the route reflector network
Exhibit.
You are provisioning Layer 2 circuits between sites CE1. CE2. andCE3
Referring to the exhibit, which statement is true?
- A . Two VLANs must be configured from PE1 to CE1.
- B . A point-to-multipoint LSP must be created between sites.
- C . Site PE1 must have a point-to-multipoint link configured towards the core
- D . Each site must have only one VLAN configured to the PE
Exhibit.
You have the LDP signaled VPLS topology as shown in the exhibit CE-B at Site-2 is multihomed to both PE-2 and PE-3
In this scenario where would you configure loop prevention?
- A . PE-2
- B . PE-3
- C . CE-B
- D . PE-1
You are deploying a new EVPN service for your customers.
You must build the service based on the following requirements
— both Layer 2 and Layer 3 functionality must be supported
— your customers must be able to support multiple VLANs in the same EVPN instance (EVI).
In this scenario which two types of routing instances should be configured? (Choose two.)
- A . VRF
- B . virtual switch
- C . virtual router
- D . EVPN
Exhibit:
Traffic is being sent from R2 to R3. The link between R2 and R3 fails.
Referring to the exhibit, which statement is correct?
- A . Traffic will automatically reroute using the shortest path, which is R2 to R1 to R3.
- B . Traffic will automatically reroute using R2 to R4 to R1 to R3.
- C . Manual intervention is required for traffic to be rerouted.
- D . Traffic will automatically reroute distributed between all available paths.
Exhibit:
Referring to the exhibit, which two statements are true? (Choose two.)
- A . This router is an ABR
- B . This router is an ASBR.
- C . There are two interfaces marked as passive.
- D . There is one interface marked as passive.
Latest JN0-663 Dumps Valid Version with 94 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
