- All Exams Instant Download
Which configuration action on either router will allow R1 and R2 to progress past the "EXSTART/DR" state?
Exhibit. An engineer has applied the above configuration to R1 and R2 However the routers OSPF adjacency never progresses past the "EXSTART-DR" slate as shown below. Which configuration action on either router will allow R1 and R2 to progress past the "EXSTART/DR" state?A . Change R1 and R2 to a...
Which command would allow you to verity receipt of a CoA message on an AOS 10 GW?
Which command would allow you to verity receipt of a CoA message on an AOS 10 GW?A . packet-capture datapath udp 3799B . packet-capture controipath udp 3799C . packet-capture interprocess udp 3799D . tcpdump host-port 3799View AnswerAnswer: B Explanation: The Change of Authorization (CoA) messages are used in network access...
What statement about the output above is correct?
Refer to the CLI output below: What statement about the output above is correct?A . The port-access role was configured with gateway-role visitorB . The secondary tunnel endpoint IP is 10.10-10.151.C . The client authenticated using dot1x.D . The UBT zone was configured to use a user-defined VRFView AnswerAnswer: B...
Which statement is true?
Exhibit. Which statement is true?A . The SSID supports HR-DSSS data ratesB . The SSID is supports 6 GHz clients.C . The SSID supports 802 11ax clients.D . The SSID supports 802 11ac clients.View AnswerAnswer: C Explanation: The exhibit shows that the SSID supports 802.11ax clients, which is indicated by...
Given the configuration example, what is required to meet this testing requirement?
A customer is evaluating device profiles on a CX 6300 switch. The test device has the following attribute: • MAC address=81:cd:93:13:ab:31 The test device needs to be assigned the "lot-prod'' role, in addition the "lot-default" role must be applied for any other device connected lo interface 1/1/1. This is a...
What directly affects the MCS used by wireless stations? (Select two.)
What directly affects the MCS used by wireless stations? (Select two.)A . SNRB . retry rateC . channel utilizationD . number of connected clientsE . frequency bandView AnswerAnswer: A E Explanation: The Modulation and Coding Scheme (MCS) used by wireless stations is directly affected by the signal-to-noise ratio (SNR) and...
What is the reason for this?
You created a new SSID with the security settings shown in the exhibit. Some, but not all users complain that client devices are unable to connect to this SS1D. What is the reason for this?A . The WPA3 Enterprise GCM-2S6 mode does not support transition mode.B . WPA3 Enterprise is...
How can HPE Aruba Networking Central identify which switch port the AP is connected to?
A customer has interfering devices that are seen over the air. They contact you and ask you to configure RAPIDS to help identify interfering and rogue APs. HPE Aruba Networking Central identifies a rogue AP and displays the connected switch port. How can HPE Aruba Networking Central identify which switch...
Which statement is true given the following CLI output from a CX 6300?
Exhibit. Which statement is true given the following CLI output from a CX 6300?A . There are no active fabric clients on the CX switch with RD 172.16.10.1B . A wired client with IP address 10.203 1.100 is on a remote CX 6300 in the fabric with loopback IP address...
What is me recommended configuration to ensure link aggregation is consistent in a campus topology using VSX with two aggregation switches and downlinks to access switches?
What is me recommended configuration to ensure link aggregation is consistent in a campus topology using VSX with two aggregation switches and downlinks to access switches?A . Use a custom LACP hash algorithm for improved load Balancing.B . Keep the MTU values at the default setting for GRE and VXLAN...
