Which security benefit does SNMPv3 offer that SNMPv2 does not offer?

Which security benefit does SNMPv3 offer that SNMPv2 does not offer?A . SSL encryptionB . ScopesC . Data confidentiallyD . RADIUS groupsView AnswerAnswer: C

April 14, 2025 No Comments READ MORE +

What command could you have issued before making changes that would have recovered the original switch configuration after ten minutes?

You need to remote into an AOS-CX switch using SSH in order to update the management IP address for future connections. Unfortunately, you mis-configured the IP address and are now locked out of the switch. What command could you have issued before making changes that would have recovered the original...

April 13, 2025 No Comments READ MORE +

What are two mechanisms supported on AOS-CX 6300 switches used in Multi-active Detection to determine the status of the Primary member? (Choose two.)

What are two mechanisms supported on AOS-CX 6300 switches used in Multi-active Detection to determine the status of the Primary member? (Choose two.)A . Management interface split detectionB . Peer switch-based detectionC . Loopback keepalivesD . ARP-basedE . BFDView AnswerAnswer: A,D

April 9, 2025 No Comments READ MORE +

Which option correctly describes a WAN network?

Which option correctly describes a WAN network?A . a group of computer resources that communicates between geographically separate locationB . the connection between two separate buildings in the same campusC . a network of devices over long distances but limited to within a single ISPD . compute resources that are...

March 23, 2025 No Comments READ MORE +

What is a benefit of choosing a 3-Tier design with routing at the Aggregation layer?

What is a benefit of choosing a 3-Tier design with routing at the Aggregation layer?A . Better Core router performance by offloading processingB . Shifting endpoint access to the Aggregation layer from the Access layerC . Using access control lists (ACLs) at the Core to improve performanceD . Connecting WAN/MPLS...

March 21, 2025 No Comments READ MORE +

Which two options are correct regarding the IEEE 802.11ax standard? (Choose two.)

Which two options are correct regarding the IEEE 802.11ax standard? (Choose two.)A . allows transmissions of up to 4.8GbpsB . is an emerging satellite connection standard to allow wireless access anywhere in the worldC . operates only in the 5GHz similar to 802.11acD . operates in both the 2.4GHz and...

March 16, 2025 No Comments READ MORE +

Which command on Access-2 port 1/1/4 will enable connectivity between PC-1 and Server-1 without any routing enabled in the network?

Refer to the exhibit Which command on Access-2 port 1/1/4 will enable connectivity between PC-1 and Server-1 without any routing enabled in the network?A . Access-2 (config-if-1/1/4)# vlan access 1, 10, 20, 255B . Access-2 (config-if-1/1/4)# vlan access 20C . Access-2 (config-if-1/1/4)# vlan 20 untag 1/1/4D . Access-2 (config-if-1/1/4)# vlan...

March 14, 2025 No Comments READ MORE +

Which statement is correct regarding powering an Aruba Access Point?

Which statement is correct regarding powering an Aruba Access Point?A . PoE or PoE+ is only used with Ethernet that is carried over multi-mode fiber cabling.B . Using switchports for this reason is unnecessary, because Aruba Access Points typically use an AC to DC power adapter to draw power.C ....

March 10, 2025 No Comments READ MORE +

Which statement is true regarding how Switch-A will forward the packet?

Refer to the exhibit. The above scenario shows a packet from the Server destined for the Firewall. Switch-A and Switch-B are bundled as VSF stack. The LAG between the VSF stack and the firewall indicates a hash function to forward the packet on port 2/1/2. Which statement is true regarding...

March 10, 2025 No Comments READ MORE +

After completing the above commands, what is the expected output of show vlan with no other vlan commanded having been added?

The section in blue can be ignored. SW1(config)# interface 1/1/1-1/1/2 SW1(config-if-<1/1/1-1/1/2)# vlan access 2 SW1(config-if-<1/1/1-1/1/2)# exit SW1(config)# interface 1/1/11-1/1/17 SW1(config-if-<1/1/11-1/1/17)# vlan access 17 SW1(config-if-<1/1/11-1/1/17)# exit After completing the above commands, what is the expected output of show vlan with no other vlan commanded having been added? A . Option AB...

March 10, 2025 No Comments READ MORE +