HP HPE6-A72 Aruba Certified Switching Associate Exam Online Training
HP HPE6-A72 Online Training
The questions for HPE6-A72 were last updated at Dec 19,2024.
- Exam Code: HPE6-A72
- Exam Name: Aruba Certified Switching Associate Exam
- Certification Provider: HP
- Latest update: Dec 19,2024
Refer to the exhibit.
You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master.
What is a valid configuration for Access-2 to join the VSF stack?
- A . Access-2# configure
Access-2(config)# vsf member 1
Access-2(config)# vsf renumber-to 2
Access-2(vsf-member-1)# link 2 2/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y - B . Access-2# configure
Access-2(config)# vsf member 2
Access-2(vsf-member-1)# link 2 1/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y - C . Access-2# configure
Access-2(config)# vsf member 2
Access-2(vsf-member-1)# link 1 1/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y - D . Access-2# configure
Access-2(config)# vsf member 1
Access-2(vsf-member-1)# link 1 1/1/28
Access-2(vsf-member-1)# exit
Access-2(config)# vsf renumber-to 2
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y
What are two primary concerns regarding layer two loops in a redundant topology? (Choose two.)
- A . routing loops
- B . costs associated with upgrading from copper to fiber
- C . multiple frame copies leading to instability of the MAC address table
- D . security issues with a redundant loop indicating to hackers that a back-door exists
- E . broadcast storms
Which port or ports should be allowed through a firewall so that an AOS-CX switch can act as an SNMP Agent?
- A . UDP 1812 and UDP 1813
- B . UDP 161
- C . TCP 443
- D . UDP 162
Refer to the exhibit.
Traffic is failing between Core-1 and Host-B. IP addressing has correctly been applied, and all interfaces are attached to the vrf GREEN.
Which configuration will correct the issue?
- A . Core-2(config)# ip route 0.0.0.0/0 10.1.1.1 vrf GREEN Host-B: assign the default-gateway address 10.1.20.181
- B . Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN Host-B: assign the default-gateway address 10.1.20.181
- C . Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN Host-B: assign the default-gateway address 10.1.20.1
- D . Host-B: assign the default-gateway address 10.1.20.181
What is Deep Packet Inspection?
- A . a machine learning method of packet inspection for the purpose of choosing which dynamic routing protocol to automatically assign
- B . a concept that applies to firewalls, when examining packets only up through Layer 4
- C . a function of Policy Based Routing that examines the entire IPv4 header to forward traffic based on factors other than destination address
- D . a firewall process of examining the packet header all the way to Layer 7 in order to determine if the packet should be permitted or denied
What is the binary conversion of the hexadecimal value 0x2001?
- A . 0010 0001
- B . 0002 0000 0000 0001
- C . 0011 0000 0000 0001
- D . 0010 0000 0000 0001
You need to remote into an AOS-CX switch using SSH in order to update the management IP address for future connections. Unfortunately, you mis-configured the IP address and are now locked out of the switch.
What command could you have issued before making changes that would have recovered the original switch configuration after ten minutes?
- A . checkpoint rollback 10
- B . checkpoint auto 10
- C . checkpoint auto confirm 10
- D . boot system secondary 10
The following command is issued:
Switch# checkpoint rollback start
What is the result?
- A . The command will fail because rollback commands must be issued from global-config mode.
- B . The switch will revert the running-configuration to the checkpoint called ‘start1 without a reboot.
- C . The command will fail because it is incomplete.
- D . The switch will use the checkpoint ‘rollback1 as the starting configuration on next reboot.
Refer to the exhibit.
The above output is the result of issuing the command show system resource-utilization.
What command should be used to enable terminal output line by line or page by page?
- A . The command page
- B . The command terminal length 30
- C . The command more
- D . The command less
Latest HPE6-A72 Dumps Valid Version with 88 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
