HP HPE0-Y53 Building HPE SDN and FlexNetwork Solutions Online Training
HP HPE0-Y53 Online Training
The questions for HPE0-Y53 were last updated at Nov 12,2024.
- Exam Code: HPE0-Y53
- Exam Name: Building HPE SDN and FlexNetwork Solutions
- Certification Provider: HP
- Latest update: Nov 12,2024
Refer to the exhibits on the Exhibit 1 and Exhibit 2 tabs.
Exhibit 1
Exhibit 2
Network clients are configured to use the switch as their default gateway in VLAN 2. The HP Comware switch places VLAN 2 in OpenFlow instance 1. An SDN application has created the flow entry shown in Exhibit 1 to route traffic from 10.1.2.0/24 to 10.1.3.0/24. Exhibit 1 does not show the output interface for the flow.
Which output interface supports the needs of this scenario?
- A . CONTROLLER
- B . ANY
- C . NORMAL
- D . TABLE
Refer to the exhibits on the Exhibit 1 and Exhibit 2 tabs.
Exhibit 1
Exhibit 2
A network administrator has set up an HP VAN SDN Controller to operate in hybrid mode. The administrator wants to confirm that the controller has properly configured an HP Comware switch to be controlled by it in hybrid mode.
Which output in the exhibit indicates that the controller is using hybrid mode.
- A . Active configuration
- B . MissRule flow entry information
- C . Flow entry 1 information
- D . Flow table
What correctly describes the role of OpenFlow in an SDN solution?
- A . OpenFlow regulates the communications among teamed SDN controllers, as well as between an SDN controller and a network infrastructure device.
- B . OpenFlow integrates the SDN controller into a larger management suite, such as the one provided in the HP Helion CloudSystem solution.
- C . OpenFlow is an open standard technology that regulates how the SDN control plane and the application plane communicates.
- D . OpenFlow is a communication protocol that an SDN controller can use to control how network devices forward traffic.
Refer to the exhibit.
A network administrator is setting up the OSPF routing for VPN instance “TenantA.” The configuration shown in this exhibit is not functioning as expected.
What must the administrator do to correct the configuration?
- A . Recreate the OSPF instance and bind it to the VPN instance.
- B . Change theOSPF process ID to match the VPN instance Route Distinguisher.
- C . Tag the OSPF advertisements with the VPN instance Route Distinguisher.
- D . Enable route leaking on the VPN instance.
A company is using HP Network Visualizer to monitor traffic transmitted and received by users in specific Active Directory user groups. The company wants to send traffic to a different server from the controller and have that server store the captured packets in PCAP format.
How would the network administrator configure this solution to meet these requirements?
- A . by setting up a remote mirroring session
- B . by setting the destination server’s IP address in the capture session
- C . by setting up a managed remote destination
- D . by setting up a remote syslog server to receive controller log messages
An SDN application submits a username and password to authenticate to the HP VAN SDN Controller, which is configured for local authentication.
If the username and password are valid, what does the controller do?
- A . creates a security hash, which the application uses to generate a valid X-Auth-Token
- B . sends the application an X-Auth-Token
- C . forwards the application an Access-Accept packet
- D . requests the last valid token the application used
Which technology is best suited for isolating tenants within a data center that must support many tenants?
- A . TRILL
- B . MDC
- C . SPBM
- D . EVI
A network administrator is setting up OpenFlow settings on an HP ProVision switch with VLANs 1, 2, 3, and 4. The switch reaches the HP VAN SDN Controller on VLAN 1. The administrator wants to enable OpenFlow on VLANs 2 and 3 but not on VLAN 4.
What is a valid configuration for the OpenFlow instances?
- A . OpenFlow instance 1 mapped to VLAN 1; OpenFlow instance 2 mapped to VLAN 2; OpenFlow instance 2 mapped to VLAN 3
- B . OpenFlow instance 1 mapped to VLAN 2; OpenFlow instance 2 mapped to VLAN 3
- C . OpenFlow instance 1 mapped to VLAN 1 and 2; OpenFlow instance 2 mapped to VLAN 1 and 3
- D . Aggregate OpenFlow instance
Refer to the exhibit.
Which design in the exhibit shows valid choices for HP switches?
- A . A
- B . B
- C . C
- D . D
Refer to the exhibits.
A network administrator has connected Comware-1 and Comware-2 on their Ten-GigabitEthernet 1/0/2 interfaces. The administrator configured both switches to support FCoE FCF mode and configured the connecting interfaces to carry FCoE traffic.
However, the configuration is not working.
The exhibit shows the output for several display commands. Based on this output, which step should the administrator take to fix the problem?
- A . Change the port link type on both Ten-GigabitEthernet 1/0/2 interfaces to hybrid.
- B . Change the port link type on both Ten-GigabitEthernet 1/0/2 interfaces to access.
- C . Change the FC mode on the Comware-2 Ten-GigabitEthernet 1/0/2 interfaces to E.
- D . Change the FC mode on the Comware-1 Ten-GigabitEthernet 1/0/2 interface to NP.
Latest HPE0-Y53 Dumps Valid Version with 105 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
