A customer is facing high and unpredictable latency on an HPE ProLiant DL380 Gen10 server equipped with P408i-a controller

Which tool can display an Array Diagnostic Report?

Reveal Solution Hide Solution

A small, expanding law firm wants to replace its single Windows server

The server will be kept in their library without a rack. They want a server that allows for internal storage growth and is capable of adding PCI adapters.

Which HPE server model type should you recommend?

Reveal Solution Hide Solution

A customer environment is being managed and monitored with HPE OneView. A review of the OneView log shows that there have been several trap storm events.

Which series of events must take place for OneView to insert a Trap Storm event entry into the log of system events?

Reveal Solution Hide Solution

A customer’s backup administrator is responsible for maintaining and coordinating all nightly backups of the company’s 30 servers.

Which HPE product can be used as the primary interface to orchestrate all backup targets and Catalyst copy functions?

Reveal Solution Hide Solution

DRAG DROP

Match each characteristic to the correct storage type.

Reveal Solution Hide Solution

Correct Answer:

Explanation:

ML /DL /DL /ML

Refer to the exhibit.

When performing a code upgrade on an HPE Nimble array, you noticed a connection failure on ESX1. Refer to the exhibit showing the complete zoning configuration of one of the HPE SN3000B switches.

What should you do to ensure storage access is not interrupted when doing the next update?

Reveal Solution Hide Solution

A customer has two HPE ProLiant Gen10 servers. They both require firmware installation.

Which HPE tool should you recommend to performing this task?

Reveal Solution Hide Solution

Read the question, and then refer to the exhibit.

<Switch-A>display interface Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state: Administratively DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address: d894-03fb-793d Description: Ten-GigabitEthernet1/0/1 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, port hardware type is STACK_SFP_PLUS Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10000 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 10, 20 VLAN permitted: 10, 20 Trunk port encapsulation: IEEE 802.1q Port priority: 0 Last link flapping: 0 hours 0 minutes 18 seconds Last clearing of counters: Never Peak input rate: 78 bytes/sec, at 2011-03-31 04:55:57 Peak output rate: 15 bytes/sec, at 2011-03-30 23:00:57 Last 300 second input: 0 packets/sec 67 bytes/sec – % Last 300 second output: 0 packets/sec 14 bytes/sec – % Input (total): 62670 packets, 8565340 bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input (normal): 62670 packets, – bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, – overruns, 0 aborts C ignored, – parity errors Output (total): 3707 packets, 1294835 bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output (normal): 3707 packets, – bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output: 0 output errors, – underruns, – buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, – no carrier

A customer added a new switch to their network. They connected it using interface Ten-GigabitEthernet 1/0/1. They are using VLAN 10 and 20 for the devices in their network.

The new switch was fully operational. Then, the customer experienced a power failure later that day and could not reach any device on the new switch after the power returned.

From the output in the exhibit, would could be the issue?

Reveal Solution Hide Solution

A customer requests a quote for an HPE storage solution that meets these requirements

• fully redundant dual-controller storage array with no single points of failure

• 1 Gb or 10 Gb ISCSI connectivity

• at least four host-facing ISCSI ports

• capable of expanding usable capacity in small increments of one-to-two disks

Which HPE storage solution should be proposed?

Reveal Solution Hide Solution

A customer needs to provide inventory management, health monitoring, status alerting, and reporting for their ProLiant servers.

Which HPE management offering meets the customer’s needs?

Reveal Solution Hide Solution