A logical interconnect group can span on multiple HPE Synergy frames for which interconnect type?
- A . Brocade 32GB Fibre Channel Switch Module for HPE Synergy
- B . HPE virtual Connect SE 32 Gb FC Module for Synergy
- C . HPE Virtual Connect SE 100 Gb F32 Module tor Synergy
- D . HPE Synergy 12 Gb SAS Connection Module
C
Explanation:
A logical interconnect group in HPE Synergy is used to define a consistent network configuration across multiple frames. The HPE Virtual Connect SE 100 Gb F32 Module for Synergy allows for logical interconnect groups to span across multiple frames. This is because the 100 Gb module supports high-speed connectivity and the necessary infrastructure to maintain consistent network configurations over multiple frames, which is essential for scalable and flexible Synergy environments.
Reference: HPE Synergy Logical Interconnect Groups
Which HPE Virtual Connect feature allows an administrator to suppress excessive inbound multicast broadcast and destination lookup failure (OLF) packets?
- A . Pause flood protection
- B . Loop protection
- C . LLDP tagging
- D . Storm control
D
Explanation:
Storm control is a feature in HPE Virtual Connect that allows administrators to suppress excessive inbound multicast, broadcast, and destination lookup failure (DLF) packets. This feature helps to mitigate the negative impact of network storms, which can degrade network performance and availability. By configuring storm control, administrators can set thresholds to limit the rate of such packets entering the network, ensuring a stable and reliable network environment.
Reference: HPE Virtual Connect Networking Features
Which statement about a new HPE SimpliVity deployment is true?
- A . New HPE SimpliVity deployments give customer flexible choice of hypervisor
- B . All new HPE SimpliVity models are based on AMD CPUs
- C . All new HPE SimpliVity models support deduplication and compression
- D . New HPE SimpliVity deployments are licensed per node not per physical socket
A
Explanation:
All new HPE SimpliVity models are designed with integrated deduplication, compression, and optimization capabilities. These features are fundamental to the HPE SimpliVity architecture, providing enhanced storage efficiency and performance. Deduplication and compression reduce the amount of data stored and transmitted, which improves the overall efficiency of data management in the hyper-converged infrastructure.
Reference: HPE SimpliVity Data Virtualization Platform
You configured a vVoI datastore using HPE Storage integration Pack for VMware vCenter.
Which storage object should you check using SSMC to verify whether vVol datastore is configured property?
- A . App Volume Set
- B . Storage Container
- C . Virtual Volume Set
- D . virtual Volume
B
Explanation:
When you configure a vVol datastore using the HPE Storage Integration Pack for VMware vCenter, the storage object to check in SSMC (HPE StoreServ Management Console) is the Storage Container. The Storage Container is a logical storage entity that houses virtual volumes (vVols) and represents the vVol datastore in the storage system. Verifying the Storage Container ensures that the vVol datastore is properly configured and managed.
Reference: HPE 3PAR StoreServ Storage Concepts Guide
Which statement about login redistribution is true?
- A . Login redistribution is available only If HPE Primera or HPE Alletra is connected directly to the HPE Synergy frame
- B . Login redistribution is a licensed feature and the number of licenses required depends on the number of active ports
- C . Login redistribution is supported only on the HPE Synergy Virtual Connect SE 32Gb FC Modules
- D . Login redistribution is used for login balancing when they are not distributed evenly over the FC links
C
Explanation:
Login redistribution is a feature that ensures logins are balanced across available FC (Fibre Channel) links. This process helps maintain optimal performance and redundancy by redistributing logins if they are not evenly distributed. This feature is essential in environments where maintaining balanced load distribution is critical for performance and reliability.
Reference: HPE Primera and Alletra 6000 Storage Guides
Which statement about an HPE Oneview support dump is true?
- A . Appliance support dump by default contains a logical enclosure support dump
- B . Support dump is a binary file that can be opened only in a dedicated application
- C . Support dump can be created if HPE Virtual Connect modules are installed in the frame
- D . Preview support dump is available only when creating an appliance support dump
A
Explanation:
An HPE OneView support dump includes various diagnostic information, and by default, it contains a logical enclosure support dump. This comprehensive dump helps in troubleshooting by providing detailed logs and configuration data from the appliance and the logical enclosures it manages, enabling effective diagnosis of issues within the managed environment.
Reference: HPE OneView User Guide
Refer to the exhibit.
Which statement about this logical interconnect group is true?
- A . The master modules are located in the interconnect bays 2 and 5
- B . For the given downlink speed, the maximum number of frames is reached
- C . Both master modules are located in the same HPE Synergy frame
- D . To use interconnect bay set 3, all compute nodes must be half-height
D
Explanation:
In HPE Synergy configurations, when using interconnect bay set 3, it implies that the compute nodes should be half-height. This is because bay set 3 is typically utilized in configurations where half-height compute nodes are used to ensure proper alignment and connectivity within the Synergy frame.
Reference: HPE Synergy Frame Setup Guide
An administrator tries to open iLO interlace from HPE OneView Instead of being automatically logged in a login prompt displays
Where should you start the troubleshooting process?
- A . At the iLO interface to verify whether the ILO Advanced license is properly applied
- B . At HPE OneView Interface to verify whether the server is In the maintenance mode
- C . At the iLO interface to verify whether the SSO certificate is removed from an iLO.
- D . At HPE OneView Interface to verify whether the iLO processor is disabled
C
Explanation:
When the iLO interface prompts for a login instead of automatically logging in via HPE OneView, a common issue is that the Single Sign-On (SSO) certificate might have been removed or is not properly configured on the iLO. Verifying the presence and validity of the SSO certificate on the iLO interface is a critical step in troubleshooting this issue.
Reference: HPE OneView and iLO Integration Guide
Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They also plan a vSAN
deployment leveraging HPE D3940 Storage Modules and SSD drives
The customer requested the following components:
– HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules
– Two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
– An appropriate number of vSAN Standard licenses for each compute node
– One HPE O3940 Storage Module with 40 SSDs – All required cables and options Which statement about this request is true?
- A . vSphere licenses should be added, as vSAN licenses do not replace vSphere licenses
- B . vSphere Standard licenses should be replaced with Enterprise Plus licenses to enable vSAN
- C . One HPE Virtual Connect SE 100Gb F32 Module for Synergy should be replaced with 50GD/S ILM
- D . 20 SSD drives should be removed from this setup, as D3940 supports only 20 SSD or SAS drives.
A
Explanation:
vSAN licenses and vSphere licenses are separate entities. While vSAN licenses cover the storage virtualization aspect of VMware’s hyper-converged infrastructure, vSphere licenses are required for the actual hypervisor operations. Therefore, the customer must ensure they have the appropriate vSphere licenses in addition to vSAN licenses for their compute nodes.
Reference: VMware vSAN Licensing Guide
Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They plan to use Distributed Switches and DRS cluster
You are preparing a proposal with the following components:
– HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules
– two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
– an appropriate number of the vSphere Standard licenses for each compute node
– one HPE D3940 Storage Modules with 40 SSDs
– all required cables and options
Which statement about this proposal is true?
- A . One HPE Virtual Connect SE 100Gb F32 Module for Synergy should be replaced with 50GD/S ILM
- B . vSphere Standard licenses should be replaced with Enterprise Pius licenses to enable requested features
- C . 2 additional HPE Synergy 480 Gen10 Plus compute modules can be added to this setup
- D . 20 SSD drives should be removed from this setup, as D3940 supports only 20 SSD or SAS drive.
B
Explanation:
The VMware vSphere Standard license does not include support for advanced features like Distributed Resource Scheduler (DRS) and Distributed Switches. These features are available only with the vSphere Enterprise Plus license. Therefore, to meet the customer’s requirement of using Distributed Switches and a DRS cluster, the proposal should include vSphere Enterprise Plus licenses instead of Standard licenses.
Reference: VMware vSphere Licensing Guide
Your customer has the following HPE Synergy setup
– 3 HPE Synergy 12000 Frames
– 4 HPE Virtual Connect SE 100 Gb F32 Modules
– 2 HPE Synergy 50 GO Interconnect Link Modules
– 36 HPE Synergy 480 Gen10 Plus compute modules
– 2 HPE Composer 2 modules
Which statement about this setup is true?
- A . To use all compute nodes, the customer must create at least two logical enclosures
- B . To manage all frames, the customer must buy two additional HPE Composer 2 modules
- C . The customer must buy 36 HPE OneView Advanced licenses to manage compute modules
- D . The customer can add one D3940 storage Module to each of the frames
A
Explanation:
In an HPE Synergy environment, a logical enclosure represents a management domain that groups multiple Synergy frames and their associated compute, storage, and fabric resources. Given the setup with 3 HPE Synergy 12000 Frames and the specified components, the customer must create at least two logical enclosures to effectively manage all compute nodes and resources across multiple frames. This ensures proper resource allocation, management, and redundancy.
Reference: HPE Synergy Logical Enclosure Guide
HOTSPOT
An HPE Synergy customer needs to prevent a timeout and loss of communication during an external switch firmware upgrade.
Click the parameter that the customer should configure within an uplink set to meet this requirement
Explanation:
To prevent a timeout and loss of communication during an external switch firmware upgrade, the customer should configure the LACP failover trigger within the uplink set. By setting the LACP failover trigger to "All active uplinks transition to offline," the configuration ensures that the traffic will be redirected to available uplinks in the event of an uplink failure or during the upgrade process, maintaining communication and preventing timeouts.
Reference: HPE Synergy Configuration Guide
Which statement about HPE Superdome Flex 280 is true?
- A . It supports 2 to 8 sockets in 2-socket increments.
- B . it cannot be managed using HPE OneView.
- C . It must be equipped with at least 768 GB of memory.
- D . It can support up to two nPars with an external RMC.
D
Explanation:
The HPE Superdome Flex 280 is a highly scalable server that supports 2 to 8 sockets in 2-socket increments. This allows for flexible scaling of compute resources based on the needs of the workload, providing a balance between performance and cost.
Reference: HPE Superdome Flex 280 QuickSpecs
You are troubleshooting an HPE OneView server profile that presents a critical state. The server profile was configured with a Link Aggregation Group
What should you check to fix the issue?
- A . if both FiexNICs are configured with the same speed
- B . If the logical enclosure is built on at least three HPE Synergy frames
- C . if both FiexNICs are connected to different networks
- D . if the logical enclosure is configured with redundant master modules
A
Explanation:
When troubleshooting a server profile in HPE OneView that is in a critical state due to a Link Aggregation Group (LAG), it is important to check if both FlexNICs are configured with the same speed. Inconsistent speeds can cause issues with link aggregation, leading to network instability and performance degradation.
Reference: HPE OneView Server Profile Troubleshooting Guide
Your customer experienced some problems caused by outdated HPE Superdome Flex firmware.
Which update method should they use to avoid these issues in the future?
- A . HPE OneView method for I/O firmware update procedure
- B . RMC CLI to update I/O and HPE Persistent Memory firmware
- C . HPE OneView IT HPE Persistent Memory firmware must be updated.
- D . HPE SUM if HPE Persistent Memory firmware must be updated
D
Explanation:
HPE System Update Manager (SUM) is the recommended method for updating firmware on HPE Superdome Flex systems, especially when HPE Persistent Memory firmware needs to be updated. HPE SUM ensures that all firmware components are updated correctly and consistently, reducing the risk of compatibility issues.
Reference: HPE Superdome Flex Firmware Update Guide
Your customer needs to move an application from an HPE Synergy 480 Gen10 Compute Module to an HPE Synergy 660 Gen 10 Compute Module. The 480 has a switch that has been manually zoned outside of HPE OneView.
What must the customer do before migrating the application?
- A . Migrate the application to a Logical JBOD and connect it to the new server
- B . Copy the server profile and assign the clone to the new hardware
- C . Edit the server profile and change server hardware type
- D . Create a new server profile template and apply to the new hardware
B
Explanation:
When migrating an application from an HPE Synergy 480 Gen10 Compute Module to an HPE Synergy 660 Gen10 Compute Module, the recommended approach is to copy the server profile and assign the clone to the new hardware. This ensures that all the necessary configuration settings, including network and storage configurations, are retained and applied to the new compute module. Since the switch zoning is manually configured outside of HPE OneView, copying the server profile helps in maintaining consistency in the network settings during the migration.
Reference: HPE OneView Server Profile Management
Your customer has me following HPE Synergy setup
– Three frames fully populated with HPE Synergy 480 Gen10 Plus modules and 25Gb/s downlink speed formulating a single logical enclosure
– Two HPE Virtual Connect SE 100Gb F32 Module for Synergy
– Four HPE Synergy 50Gb interconnect Link Module
– Six HPE Synergy Virtual Connect SE 32Gb FC Modules
The customer needs to add a frame.
Which statement about the expansion of this setup is true?
- A . The additional frame must have HPE Virtual Connect FC modules installed
- B . The customer can grow the existing logical enclosure up to 5 frames
- C . The customer has to create a new logical enclosure for the additional frame
- D . The additional frame cannot have 12Gb SAS connection modules installed
B
Explanation:
HPE Synergy allows scaling of logical enclosures up to 5 frames. Given the current setup of three frames fully populated with HPE Synergy 480 Gen10 Plus modules and other specified components, the customer can add another frame to the existing logical enclosure. This flexibility in scaling ensures that the logical enclosure can be expanded without the need to create a new logical enclosure, provided that the necessary interconnect modules are in place.
Reference: HPE Synergy Planning Guide
HOTSPOT
Click the area within the iLO management interface that will allow you to access workload Advisor.
Explanation:
The Performance section within the iLO management interface provides access to the Workload Advisor. This feature offers insights and analytics regarding the server’s performance, helping to optimize workloads and manage resources efficiently.
Reference: HPE iLO 5 User Guide
Your customer plans to deploy HPE OneView for VMware vCenter Server together with HPE Storage Integration Pack for VMware vCenter. The customer wants to use them to manage HPE Synergy Gen10 compute modules. HPE ProLiant Gen 10 servers and an MSA array.
Which statement about compatibility of the existing environment with the planned software components is true?
- A . Both HPE Synergy Gen10 full-height compute module plugins will require a license
- B . HPE OneView for VMware vCenter Server does not support standalone HPE ProLiant servers
- C . To use the required plugins HPE ProLiant Gen10 systems must be managed using HPE OneView
- D . HPE Storage integration Pack for VMware vCenter does not support MSA arrays
C
Explanation:
The HPE Storage Integration Pack for VMware vCenter is designed to provide management capabilities for HPE storage arrays within the VMware vCenter environment. However, it does not support MSA arrays. This means that while you can manage HPE Synergy Gen10 compute modules and HPE ProLiant Gen10 servers, the MSA array will not be manageable through the HPE Storage Integration Pack.
Reference: HPE Storage Integration Pack for VMware vCenter User Guide
Refer to the exhibit.
Which statement about this logical interconnect group is true?
- A . Both modules are located in different frames for redundancy
- B . For an uplink set, ports from different modules can be selected
- C . interconnect modules are installed in interconnect bays 1 and 4
- D . An additional license is required to change the enclosure count
18/84
C
Explanation:
In the HPE Synergy setup shown in the exhibit, the interconnect type is Virtual Connect SE 32Gb FC Module for Synergy with an enclosure count of 1 and interconnect bay set 1. Typically, in such configurations, the interconnect modules are installed in bays 1 and 4 for redundancy. This placement ensures high availability and failover capabilities.
Reference: HPE Synergy Interconnects Configuration Guide
DRAG DROP
You need to setup HPE Synergy frames after hardware components are discovered within HPE OneView.
Put the steps to achieve this goal into the coned order in the answer area on the right.
Explanation:
To set up HPE Synergy frames after the hardware components are discovered within HPE OneView, the following steps should be followed in the correct order:
Create an enclosure group.
Create a logical interconnect group with uplink sets.
Define all required networks.
Create a logical enclosure.
Create server profile templates and server profiles.
Create an enclosure group: This step involves defining the enclosure group, which includes the configurations for the enclosure such as firmware baselines and logical interconnect groups.
Create a logical interconnect group with uplink sets: Next, set up the logical interconnect group, which includes the uplink sets that define the connectivity from the enclosures to the data center networks.
Define all required networks: After setting up the logical interconnect group, define all the necessary networks that will be used within the HPE Synergy environment.
Create a logical enclosure: Create a logical enclosure by combining the physical enclosures with the defined enclosure group, effectively binding the hardware configuration with the logical settings.
Create server profile templates and server profiles: Finally, create server profile templates and individual server profiles to apply the required configuration settings to the compute modules.
Reference: HPE OneView User Guide
Your customer plans to add four HPE Synergy frames to an existing management ring Ail installed frames are equipped with two 2-port FLM modules, while new frames will be equipped with 4-port FLM modules.
Which statement about mixing different FLM modules is true?
- A . Existing 2-port FLM modules must be replaced with 4-port FLM modules
- B . A management ring can contain mixed frame link module configurations
- C . A management ring with mixed FLM modules cannot have more than 12 frames
- D . Mixing different FLM modules is allowed if all of them have the same firmware version
B
Explanation:
In HPE Synergy, a management ring can indeed contain mixed frame link module (FLM) configurations. This means you can have a mix of 2-port and 4-port FLM modules within the same management ring without needing to replace the existing 2-port modules. This flexibility allows for gradual upgrades and scalability within the management ring.
Reference: HPE Synergy Management Guide
You plan to configure a Link Aggregation Group (LAG) for two connections within a server profile for a compute node running an ESXI system.
What is required from the VMware side to enable LAG?
- A . Virtual Distributed Switch
- B . vSphere Standard license
- C . Load balancing cluster
- D . Dedicated VMKernel port
A
Explanation:
To configure a Link Aggregation Group (LAG) for two connections within a server profile for a compute node running an ESXi system, a Virtual Distributed Switch (VDS) is required from the VMware side. VDS allows for the configuration of LAGs and provides advanced network features such as centralized management and monitoring, which are essential for setting up and managing LAGs.
Reference: VMware vSphere Networking Guide
Which statement about HPE OneView milestone releases is true?
- A . A milestone release is a release which must be installed on HPE Composer to support current version of the Service Pack for Synergy
- B . A milestone release is a release that is published when HPE releases new hardware components to
immediately support new systems - C . A milestone release is available for selected partners that give access to HPE OneView features which are not officially announced.
- D . A milestone release is a release with an enhanced update architecture mat is a prerequisite prior to updating to a subsequent release.
D
Explanation:
A milestone release in HPE OneView refers to a version that includes significant architectural enhancements and updates. It serves as a prerequisite for subsequent updates, ensuring that the system is prepared for the next set of features and improvements. This type of release is essential for maintaining compatibility and stability as new hardware components and features are introduced.
Reference: HPE OneView Release Notes
Your customer has an HPE Synergy frame equipped with a D3940 Storage Module. Each of the compute nodes has an appropriate storage controller Installed and two 12Gb SAS switches installed in the first fabric.
The customer reports that compute nodes cannot access the storage module.
What should you verify first when troubleshooting this problem?
- A . If the D3940 module is imported in managed state that allows volume provisioning.
- B . If there Is a logical interconnect created based on the 12Gb SAS switches.
- C . If the D3940 storage module is property licensed through HPE OneView interface.
- D . If there is at least one ISCSI network configured that will provide access to the module.
B
Explanation:
When compute nodes cannot access the D3940 Storage Module in an HPE Synergy environment, the first thing to check is whether a logical interconnect has been created based on the 12Gb SAS switches. Logical interconnects are essential for defining the connection and communication pathways between the compute nodes and the storage module. Without a proper logical interconnect configuration, the compute nodes will not be able to access the storage module.
Reference: HPE Synergy Configuration and Management Guide
Your customer wants to add dedicated Fibre Channel connectivity to the HPE Synergy frame running HPE Synergy 480 Gen10 compute modules, each with one CPU socket populated Currently they use two 12 Gb SAS switches and two HPE Virtual Connect SE 100Gb F32 Modules for HPE Synergy installed in third fabric.
What must be done to enable dedicated FC connectivity for this HPE Synergy frame?
- A . A second CPU must be installed for all HPE Synergy 480 Gen10 compute nodes.
- B . For Brocade switches, a logical interconnect group must be created in HPE OneView.
- C . For VC-FC modules, all of server facing ports must be property licensed.
- D . SAS switches must be moved to second fabric and FC modules Installed in the first one.
A
Explanation:
To enable dedicated Fibre Channel (FC) connectivity in an HPE Synergy frame, if using Brocade switches, it is necessary to create a logical interconnect group in HPE OneView. This group defines the configuration and management of FC connectivity for the compute modules. Properly configuring and managing this logical interconnect group ensures that the compute modules can establish dedicated FC connections.
Reference: HPE OneView for Synergy FC Configuration Guide
Your customer plans to deploy ESXi systems to HPE Synergy and HPE ProLiant servers using HPE OneView for VMware vCenter Server.
Which statement about HPE OneView for VMware vCenter Server functionality is true for this environment?
- A . HPE ProLiant servers need an HPE OneView for VMware vCenter Server license for full functionality
- B . Individual systems can be added to HPE OneView for VMware vCenter Server through an ILO management processor
- C . HPE Synergy requires HPE Composer 2 for full functionality of HPE OneView for VMware vCenter Server
- D . Only systems managed using HPE Oneview can use HPE Oneview for VMware vCenter Server functionalities
B
Explanation:
HPE OneView for VMware vCenter Server provides integrated management and monitoring capabilities for systems managed by HPE OneView. This means that to leverage the full functionality of HPE OneView for VMware vCenter Server, the systems (both HPE Synergy and HPE ProLiant servers) must be managed through HPE OneView. This integration allows for comprehensive infrastructure management directly from the VMware vCenter interface.
Reference: HPE OneView for VMware vCenter Server User Guide
Your customer has an HPE Synergy platform deployed and managed using HPE OneView. The customer also has HPE Superdome Flex with RMC deployed They plan to deploy a second nPar and HPE Superdome Flex 280 They plan to manage new components using HPE OneView.
What must be done to achieve this goal?
- A . The customer must use IL05 to add HPE Superdome Flex systems to HPE OneView
- B . The customer should deploy an HPE OneView appliance for HPE Superdome Flex management
- C . The customer must add a second Rack Management Controller for HPE Superdome Flex 280
- D . The customer has to add HPE Superdome Flex to the HPE OneView used to manage HPE Synergy
D
Explanation:
To manage HPE Superdome Flex systems, including the new Superdome Flex 280, using HPE OneView, the customer should deploy a dedicated HPE OneView appliance specifically for HPE Superdome Flex management. This approach ensures that the Superdome Flex systems are properly integrated and managed within the HPE OneView environment, allowing for consistent and centralized management alongside other HPE infrastructure.
Reference: HPE Superdome Flex Management with HPE OneView
Which statement about manual orchestration during the firmware update is true?
- A . It is supported only for logical enclosures with at least three frames
- B . It provides an ability to select and update one side of the Interconnect topology at a time
- C . It provides the ability to install an older firmware version than currently Installed In the interconnect
- D . It allows all the interconnect modules to be activated manually at the same time.
B
Explanation:
Manual orchestration during a firmware update allows administrators to control the update process more precisely. Specifically, it enables the selection and update of one side of the interconnect topology at a time. This capability is particularly useful in maintaining network availability and minimizing downtime during the update process, as one side can be updated and verified before proceeding to the other side.
Reference: HPE OneView Firmware Update Guide
HOTSPOT
Click the option that will allow you to change the ESXI image used In an OS Deployment Plan.
Explanation:
The Lifecycle Manager in the vSphere Client interface is used for managing and updating ESXi hosts, including changing the ESXi image used in an OS Deployment Plan. This tool allows administrators to import, export, and apply different ESXi images, ensuring that the hosts are running the desired version and configuration of ESXi.
Reference: VMware vSphere Lifecycle Manager Guide
Your customer reports that they cannot deploy HPE Synergy compute nodes using HPE OneView for VMware vCenter Server (HPE OV4VC).
What should you check during troubleshooting process?
- A . If HPE OneView credentials are added in vCenter Server
- B . If an compute nodes are added to the vCenter Server
- C . If the HPE Oneview instance Is integrated with HPE OV4VC.
- D . If vCenter Server is licensed in the HPE Oneview interface
C
Explanation:
When troubleshooting the deployment of HPE Synergy compute nodes using HPE OneView for VMware vCenter Server (HPE OV4VC), it’s essential to verify that HPE OneView credentials are correctly added in the vCenter Server. Proper integration and authentication are necessary for HPE OV4VC to communicate and manage the compute nodes effectively.
Reference: HPE OneView for VMware vCenter Server User Guide
You need to configure a RoCE network to enable lossless networking for HPE J2000 Flash Enclosure support.
Which interconnects are required to support this connection? (Select two.)
- A . HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy
- B . HPE Virtual Connect SE 16Gb FC Module for HPE Synergy
- C . HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy
- D . HPE Virtual Connect SE 32Gb FC Module for HPE Synergy
- E . Brocade 16Gb Fibfe Channel SAN Switch Module for HPE Synergy
- F . Brocade 32Gb Fibre Channel SAN Switch Module for HPE Synergy
AC
Explanation:
To configure a RoCE (RDMA over Converged Ethernet) network for HPE J2000 Flash Enclosure support, you need interconnects that support high-bandwidth, low-latency Ethernet connections. The HPE Virtual Connect SE 40Gb F8 Module and the HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy are suitable choices, as they provide the necessary capabilities for RoCE and lossless networking.
Reference: HPE Synergy Interconnect Modules
Which statement about the SY480 Gen10 Plus Compute Module is true?
- A . It cannot be mixed with Gen9 compute modules in the same frame.
- B . It supports 8 memory channels and memory DIMMs of up to 256GB.
- C . It only supports NVDIMM Persistent Memory.
- D . It supports "3rd Gen AMO EPYC Server Processors with 64 cores.
A
Explanation:
The HPE Synergy 480 Gen10 Plus Compute Module supports 8 memory channels and can accommodate memory DIMMs of up to 256GB. This capability ensures high memory bandwidth and large memory capacity, which are essential for demanding workloads and applications.
Reference: HPE Synergy 480 Gen10 Plus QuickSpecs
What is a restriction of using a RoCE network?
- A . It is by default configured as an untagged network and cannot be a part of a network set.
- B . It does not support Private VLAN and Multicast VLAN.
- C . it is not supported with HPE Virtual Connect SE 40 GD F8 Module for HPE Synergy.
- D . It does not support smart link and private network features.
B
Explanation:
A restriction of using a RoCE (RDMA over Converged Ethernet) network is that it does not support smart link and private network features. These features are essential for certain network configurations and use cases, but they are not available in RoCE networks, which are designed for high-performance, low-latency communication.
Reference: HPE Synergy Networking Guide
Your customer plans to deploy VMware ESXi 7. 0 U2, and they are looking for a hardware platform that will allow them to use up to 16 CPU sockets
Which HPE compute system meets the customer requirements?
- A . HPE ProLiant DL580 Gen10
- B . HPE ProLiant OL380 Gen 10 Plus
- C . HPE Synergy 480 Gen10 Plus
- D . HPE Superdome Flex system
D
Explanation:
The HPE Superdome Flex system is the only HPE compute system that supports up to 16 CPU sockets, making it suitable for customers who require a hardware platform with such high scalability. The Superdome Flex is designed for mission-critical workloads and provides exceptional scalability and performance.
Reference: HPE Superdome Flex QuickSpecs
DRAG DROP
Your customer plans to use HPE OneView for VMware vCenter Server to deploy ESXi systems. They created a server profile template that they want to use in HPE OneView.
Put the steps required to configure HPE OneView for VMware vCenter Server on the left into their correct order on the right.
Explanation:
To configure HPE OneView for VMware vCenter Server to deploy ESXi systems, follow these steps in the correct order:
Add HPE OneView credentials to the vCenter Server and create OS Deployment Plan.
Add vCenter Server to HPE OneView for VMware vCenter Server.
Upload HPE-friendly ESXi image.
Deploy new ESXi systems using vCenter Server interface.
Add HPE OneView credentials to the vCenter Server and create OS Deployment Plan: Integrate HPE OneView with vCenter Server by adding the necessary credentials and setting up the OS Deployment Plan.
Add vCenter Server to HPE OneView for VMware vCenter Server: Ensure that vCenter Server is added to HPE OneView for VMware vCenter Server to enable communication and management.
Upload HPE-friendly ESXi image: Upload an ESXi image that is optimized for HPE hardware to the vCenter Server for use in the deployment process.
Deploy new ESXi systems using vCenter Server interface: Use the vCenter Server interface to deploy new ESXi systems based on the created server profile template and the uploaded ESXi image.
These steps ensure a seamless deployment and management of ESXi systems using HPE OneView integrated with VMware vCenter Server.
Reference: HPE OneView for VMware vCenter Server User Guide
Your customer plans to deploy VMware ESXi 7 0 U2 and they are looking for a hardware platform mat wilt allow them to use up to 24 TB of physical memory.
Which HPE compute system meets this customer’s requirements?
- A . HPE ProLiant DL380 Gen 10 Plus
- B . HPE Synergy 480 Gen10 Plus
- C . HPE ProLiant DL560 Gen10
- D . HPE Superdome Flex 280
D
Explanation:
The HPE Superdome Flex 280 is the appropriate hardware platform for a customer requiring up to 24 TB of physical memory. This system is designed for high scalability and performance, supporting large memory configurations suitable for demanding applications and workloads.
Reference: HPE Superdome Flex 280 QuickSpecs
Which compute node parameters are captured within server hardware type?
- A . Number of the CPUs
- B . installed operating system
- C . Mezzanine card configuration
- D . Size of the memory Installed
B
Explanation:
The server hardware type in HPE OneView captures parameters such as the mezzanine card configuration. This information is crucial for defining the connectivity and expansion capabilities of the compute node, ensuring that the appropriate resources are available for specific workloads.
Reference: HPE OneView Server Hardware Guide
Your customer has 6 logical enclosures spanning 18 HPE Synergy frames. The customer needs to add one more logical enclosure based on 5 HPE Synergy frames
How will this change impact the customer environment?
- A . The customer can add a new logical enclosure to the existing setup because the maximum number of logical enclosures in a single management ring is not reached.
- B . The customer has to expand the management ring capacity either by adding HPE Composer 2 modules or adding memory to reach 128GB per module.
- C . The customer has to create a new management ring for new logical enclosure because the maximum number of frames m a single management ring is reached.
- D . The customer can add a new logical enclosure to an existing setup once all required licenses are added to HPE OneView and associated with the new frames.
C
Explanation:
HPE Synergy management rings have a maximum capacity for the number of frames they can manage. With 18 frames already managed in 6 logical enclosures, adding 5 more frames would exceed this capacity. Therefore, the customer needs to create a new management ring for the new logical enclosure to ensure proper management and operation.
Reference: HPE Synergy Management Guide
Your customer added a new Ethernet network in HPE Oneview mat is used to manage their HPE Synergy platform.
When the customer tries to connect one of the compute nodes to this network through the server profile, this network is not available.
What must be done to fix this issue?
- A . Check the Logical Enclosure settings and verify if the maximum number of networks allowed for this LE is reached.
- B . To make this network available to use in the server profile, the customer must enable the Smart Link feature within network definition.
- C . The newly created network must be added to the uplink set within the LIG, and Logical
interconnect configuration must be updated from the LIG. - D . Check within the server profile which server hardware is used and perform the Refresh operation on this compute node to get the latest adapter information.
C
Explanation:
When a new Ethernet network is created in HPE OneView and is not available in the server profile, it is typically because the network has not been added to the uplink set within the Logical Interconnect Group (LIG). To resolve this issue, the network must be included in the uplink set configuration, and then the logical interconnect configuration must be updated from the LIG to propagate the changes.
Reference: HPE OneView Networking Guide