- All Exams Instant Download
In the switching network shown in the figure, VLAN10 is set as Super VLAN on switch SWA, VLAN2 and VLAN3 are Sub VLANs of VLAN10, port Ethernet1/0/3 is a Trunk port, PVID is VLAN1, and all VLANs are allowed to pass; VLAN2 and VLAN20 are created on switch SWB, port Ethernet1/0/4 is a Trunk port, PVID is VLAN1, and all VLANs are allowed to pass. After setting the IP addresses of each device as shown in the figure, you can judge which of the following?
In the switching network shown in the figure, VLAN10 is set as Super VLAN on switch SWA, VLAN2 and VLAN3 are Sub VLANs of VLAN10, port Ethernet1/0/3 is a Trunk port, PVID is VLAN1, and all VLANs are allowed to pass; VLAN2 and VLAN20 are created on switch SWB, port...
In the network shown in the figure, after completing the corresponding configuration on the switch SWA, when the switch SWA receives the data frame accessing the PCB from the PCA, it determines whether to check the MAC address table or the routing table?
In the network shown in the figure, after completing the corresponding configuration on the switch SWA, when the switch SWA receives the data frame accessing the PCB from the PCA, it determines whether to check the MAC address table or the routing table? A . VLAN attributes of data framesB...
Which of the following statements about IToIP is incorrect?
Which of the following statements about IToIP is incorrect? A . IToIP closely connects applications and infrastructure, greatly improving the operating efficiency of IT systems.B . IToIP requires that IT systems be built using IP networks as infrastructure.C . Various IT resources can easily share and use standard IP infrastructure...
Which of the following is the core goal of high-reliability redundant network design?
Which of the following is the core goal of high-reliability redundant network design?A . Maximize network bandwidthB . Maximize network access securityC . Minimize the existence of single point failures in the networkD . Minimize network management complexityView AnswerAnswer: C
In the switching network shown in the figure, VLAN 10 is set as Super VLAN on switch SWA, VLAN2 and VLAN3 are Sub VLANs of VLAN 10, port Ethernet/0/3 is a Trunk port, PVID is VLAN1, and all VLANs are allowed to pass; VLAN2~VLAN20 are created on switch SWB, port Ethernet/0/4 is a Trunk port, PVID is VLAN1, and all VLANs are allowed to pass. After setting the IP addresses of each device as shown in the figure, check the MAC address table on SWB and you can determine that PCA belongs to?
In the switching network shown in the figure, VLAN 10 is set as Super VLAN on switch SWA, VLAN2 and VLAN3 are Sub VLANs of VLAN 10, port Ethernet/0/3 is a Trunk port, PVID is VLAN1, and all VLANs are allowed to pass; VLAN2~VLAN20 are created on switch SWB, port...
After the configuration is complete, can you tell which one the PCA will join?
The IP address of host PCA is 40.1.1.1, and the MAC address is 0011.1111.1111. It is connected to the GigabitEthernet1/0/1 port of switch SWA. The following commands are configured on switch SWA: [SWA] vlan 10 [SWA-vlan10] quit [SWA] vlan 20 [SWA-vlan20] protocol-vlan ipv4 [SWA-vlan20] quit [SWA] vlan 30 [SWA-vlan30] quit...
If the switching SWE is the master node of sub-ring 2, which of the following can be known from the above information?
The figure shows the networking application of RRPP. The customer LAN switches SWA, SWB, SWC, and SWD form the RRPP ring main ring 1, and the switches SWB, SWC, and SWE form the sub-ring 2. If the switching SWE is the master node of sub-ring 2, which of the following...
When all interconnected ports are UP and STP and OSPF calculations are complete, which of the following descriptions of network connectivity are correct?
SWA/SWB/SWC are in the same MSTP region and configured with the same region configuration Stp region-configuration region-name h3c Instance 1 vlan 10 Instance 2 vlan 20 Instance 2 vlan 30 Active region-configuration The ports of the three interconnected links are all Access and belong to the VLANs identified in the...
Regarding the description of Private VLAN technology and Super VLAN technology, which of the following is correct?
Regarding the description of Private VLAN technology and Super VLAN technology, which of the following is correct?A . Super VLAN technology is also called VLAN aggregation. Its main purpose is to solve the problem of IP address waste or insufficient VLAN interface quantity.B . Private VLAN is a Layer 2...
Which request operation does SNMP v2c add compared to SNMP v1 protocol?
Which request operation does SNMP v2c add compared to SNMP v1 protocol?A . GetRequestB . GetNextRequestC . GetBulkRequestD . SetRequestView AnswerAnswer: C
