- All Exams Instant Download
In the switching network as shown in the figure, VLAN10 is set as Isolate-user-vlan on the switch SWA, VLAN2 and VLAN3 are the Secondary VLAN of VLAN 10; VLAN2? VLAN20 is created on the switch SWB, and VLAN20 is set as Isolate-user-vlan , VLAN4 is the Secondary VLAN of VLAN20. After setting the IP address of each device, check the MAC address table on SWA, it will show that the PCB belongs to (choose one or more)
In the switching network as shown in the figure, VLAN10 is set as Isolate-user-vlan on the switch SWA, VLAN2 and VLAN3 are the Secondary VLAN of VLAN 10; VLAN2? VLAN20 is created on the switch SWB, and VLAN20 is set as Isolate-user-vlan , VLAN4 is the Secondary VLAN of VLAN20....
In the switching network as shown in the figure, VLAN10 is set as SuperVLAN on the switch SWA, and VLAN2 and VLAN3 are Sub VLANs of VLAN10. The PCA and PCB are required to communicate with each other. After the switch SWA configuration is completed, the PCA can ping the PCB. After that, regarding the ARP entries on the PCA, PCB and switch SWA, the correct description below is _ (choose one or more)
In the switching network as shown in the figure, VLAN10 is set as SuperVLAN on the switch SWA, and VLAN2 and VLAN3 are Sub VLANs of VLAN10. The PCA and PCB are required to communicate with each other. After the switch SWA configuration is completed, the PCA can ping the...
In the switching network as shown in the figure, VLAN10 is set as Super VLAN on switch SWA, VLAN2 and VLAN3 are Sub VLAN of VLAN10, port Ethernet1/0/3 is Trunk port, PVID is VLAN1, allowing all VLANs to pass through; Create VLAN2~VLAN20 on SWB, port Ethernet1/0/4 as Trunk port, PVID is VLAN1, allowing all VLANs to set the IP address of each device as shown in the figure, check the MAC address table on SWA, you can judge PCC belongs to
In the switching network as shown in the figure, VLAN10 is set as Super VLAN on switch SWA, VLAN2 and VLAN3 are Sub VLAN of VLAN10, port Ethernet1/0/3 is Trunk port, PVID is VLAN1, allowing all VLANs to pass through; Create VLAN2~VLAN20 on SWB, port Ethernet1/0/4 as Trunk port, PVID...
In the switching network as shown in the figure, VLAN10 is set as Isolate-user-vlan on the switch SWA, VLAN2 and VLAN3 are set as the Secondary VLAN of VLAN 10; VLAN2? VLAN20 is created on the switch SWB, and VLAN20 is set as Isolate-user-vlan , VLAN4 is VLAN20 Secondary VLA after setting the IP address of each device as shown in the figure, if the local ARP proxy function is enabled on both SWA and SWB, and both SWA and SWB are allowed to send ICMP packets, then on PCA Run the tracert 10.1.1.2 command, the PCA shows that the destination IP address reached by the first hop is
In the switching network as shown in the figure, VLAN10 is set as Isolate-user-vlan on the switch SWA, VLAN2 and VLAN3 are set as the Secondary VLAN of VLAN 10; VLAN2? VLAN20 is created on the switch SWB, and VLAN20 is set as Isolate-user-vlan , VLAN4 is VLAN20 Secondary VLA...
Regarding the relationship between SuperVLAN and Sub VLAN, the following description is correct
Regarding the relationship between SuperVLAN and Sub VLAN, the following description is correctA . SuperVLAN is equivalent to aggregating Sub VLANs so that all Sub VLANs share the same Layer 3 interfaceB . SuperVLAN only establishes Layer 3 interfaces, responsible for Layer 3 forwarding of Sub VLANC . Sub VLAN...
The switch SWA and SWB are connected together by two optical fiber Gigabit Ethernet links. The switch SWA has the following interface configuration:
The switch SWA and SWB are connected together by two optical fiber Gigabit Ethernet links. The switch SWA has the following interface configuration: [SWA]interface GigabitEthernet 1/0/1 [SWA-GigabitEthernet1/0/1]gvrp [SWA-GigabitEthernet1/0/1]port link-type trunk [SWA-GigabitEthernet1/0/1]port trunk permit vlan 1 10 [SWA]interface GigabitEthernet 1/0/2 [SWA-GigabitEthernet1/0/2]port link-type trunk [SWA-GigabitEthernet1/0/2]port trunk permit vlan 1 10 It can...
The configuration command to set the current VLAN type to SuperVLAN on H3C series switches is
The configuration command to set the current VLAN type to SuperVLAN on H3C series switches isView AnswerAnswer: supervlan
After executing the display interface Ethernet 1/0/1 command on the switch SWA, the output information is as follows:
After executing the display interface Ethernet 1/0/1 command on the switch SWA, the output information is as follows: [SWA]display interface Ethernet 1/0/1 Ethernetl/0/1 current state: UP PVID: 10 Mdi type: auto Link delay is 0(sec) Port link-type: trunk VLAN passing: 1 (default vlan), 10 VLAN permitted: 1 (default vlan), 2-4094...
In the switching network as shown in the figure, set VLAN10 as Isolate-user-vlan VLAN2 and VLAN3 as the Secondary VLAN of VLAN10 on the switch SWA. VLAN10 virtual interface link layer UP on the following switch SWA? (Select one or more )
In the switching network as shown in the figure, set VLAN10 as Isolate-user-vlan VLAN2 and VLAN3 as the Secondary VLAN of VLAN10 on the switch SWA. VLAN10 virtual interface link layer UP on the following switch SWA? (Select one or more ) A. GigabitEthernet1/0/1 port is up B. GigabitEthernet1/0/2 port...
The Ethernets port configuration of the switch SWA is as follows:
The Ethernets port configuration of the switch SWA is as follows: interface Ethernet 1/0/1 port link-type trunk port trunk permit vlan 10 port trunk pvid vlan 20 Now you need to modify the Ethernet1/0/1 port of the switch SWA to a Hybrid port, PVID is VLAN20, and the data frame...
