- All Exams Instant Download
Based on output shown in the exhibit, which two commands can be used by SD-WAN rules?
Refer to the exhibit. Based on output shown in the exhibit, which two commands can be used by SD-WAN rules? (Choose two.)A . set cost 15. B. set source 100.64.1.1. C. set priority 10. D. set load-balance-mode source-ip-based.View AnswerAnswer: C,D
What must you configure to enable ADVPN?
Refer to the exhibit. What must you configure to enable ADVPN?A . On the hub VPN, only the device needs additional phase one sett B. ADVPN should only be enabled on unmanaged FortiGate devices. C. Each VPN device has a unique pre-shared key configured separately on phase one D. The...
Based on the exhibit, which algorithm does SD-WAN use to distribute traffic that does not match any of the SD-WAN rules, among the member interfaces?
Refer to Exhibit: Based on the exhibit, which algorithm does SD-WAN use to distribute traffic that does not match any of the SD-WAN rules, among the member interfaces?A . All traffic from a source IP to a destination IP Is sent to the same interface. B. All traffic from a...
Which diagnostic command can you use to show the SD-WAN rules interface information and state?
Which diagnostic command can you use to show the SD-WAN rules interface information and state?A . diagnose sys sdwan route-tag-list. B. diagnose sys sdwan service. C. diagnose sys sdwan member. D. diagnose sys sdwan neighbor.View AnswerAnswer: B Explanation: https://community.fortinet.com/t5/FortiGate/Technical-Tip-Diagnostic-commands-to-check-the-status-of-the-SD/ta-p/194246
Which three protocols are available only on the command line to configure as performance SLA status check? (Choose three.)
Which three protocols are available only on the command line to configure as performance SLA status check? (Choose three.)A . smtp B. tcp-echo C. twamp D. udp-echo E. icmpView AnswerAnswer: B,C,D
What are the two minimum configuration requirements for an outgoing interface to be selected once the SD-WAN logical interface is enabled? (Choose two)
What are the two minimum configuration requirements for an outgoing interface to be selected once the SD-WAN logical interface is enabled? (Choose two)A . Specify outgoing interface routing cost. B. Configure SD-WAN rules interface preference. C. Select SD-WAN balancing strategy. D. Specify incoming interfaces in SD-WAN rules.View AnswerAnswer: A,B
In the default SD-WAN minimum configuration, which two statements are correct when traffic matches the default implicit SD-WAN rule? (Choose two)
In the default SD-WAN minimum configuration, which two statements are correct when traffic matches the default implicit SD-WAN rule? (Choose two)A . Traffic has matched none of the FortiGate policy routes. B. Matched traffic failed RPF and was caught by the rule. C. The FIB lookup resolved interface was the...
Which two statements about the debug output are true?
Refer to the exhibit. Which two statements about the debug output are true? (Choose two)A . The debug output shows per-IP shaper values and real-time readings. B. FortiGate provides statistics and reading based on historical traffic logs. C. Traffic being controlled by the traffic shaper is under 100 KB/s. D....
Which two statements about SLA targets and SD-WAN rules are true? (Choose two.)
Which two statements about SLA targets and SD-WAN rules are true? (Choose two.) A. Member metrics are measured only if an SLA target is configured. B. SLA targets are used only by SD-WAN rules that are configured with Lowest Cost (SLA) or Maximize Bandwidth (SLA) as strategy. C. When configuring...
Based on the exhibits, which statement is correct?
Refer to exhibits. Exhibit A, which shows the SD-WAN performance SLA and exhibit B shows the health of the participating SD-WAN members. Based on the exhibits, which statement is correct?A . The dead member interface stays unavailable until an administrator manually brings the interface back. B. Port2 needs to wait...
