Which the following events can trigger the election of a new primary unit in a HA cluster? (Choose two.)

Which the following events can trigger the election of a new primary unit in a HA cluster? (Choose two.)A . Primary unit stops sending HA heartbeat keepalives.B . The FortiGuard license for the primary unit is updated.C . One of the monitored interfaces in the primary unit is disconnected.D ....

January 9, 2024 No Comments READ MORE +

Why?

Refer to the exhibit, which contains a screenshot of some phase 1 settings. The VPN is not up. To diagnose the issue, the administrator enters the following CLI commands to an SSH session on FortiGate: diagnose vpn ike log-filter dst-addr4 10.0.10.1 diagnose debug application ike -1 However, the IKE real-time...

January 8, 2024 No Comments READ MORE +

What should the administrator check?

Examine the output from the 'diagnose debug authd fsso list' command; then answer the question below. # diagnose debug authd fsso list ―FSSO logons-IP: 192.168.3.1 User: STUDENT Groups: TRAININGAD/USERS Workstation: INTERNAL2. TRAINING. LAB The IP address 192.168.3.1 is NOT the one used by the workstation INTERNAL2. TRAINING. LAB. What should...

January 8, 2024 No Comments READ MORE +

Which two statements about this debug output are correct?

Refer to the exhibit, which contains partial output from an IKE real-time debug. Which two statements about this debug output are correct? (Choose two.)A . The initiator provided remote as its IPsec peer ID.B . It shows a phase 2 negotiation.C . Perfect Forward Secrecy (PFS) is enabled in the...

January 7, 2024 No Comments READ MORE +

Which statements are correct regarding the output?

View the exhibit, which contains the output of get sys ha status, and then answer the question below. Which statements are correct regarding the output? (Choose two.)A . The slave configuration is not synchronized with the master.B . The HA management IP is 169.254.0.2.C . Master is selected because it...

January 7, 2024 No Comments READ MORE +

Four FortiGate devices configured for OSPF connected to the same broadcast domain. The first unit is elected as the designated router. The second unit is elected as the backup designated router Under normal operation, how many OSPF full adjacencies are formed to each of the other two units?

Four FortiGate devices configured for OSPF connected to the same broadcast domain. The first unit is elected as the designated router. The second unit is elected as the backup designated router Under normal operation, how many OSPF full adjacencies are formed to each of the other two units?A . 1B...

January 6, 2024 No Comments READ MORE +

Which of the following statements describes IPS adaptive scanning?

The CLI command set intelligent-mode <enable | disable> controls the IPS engine’s adaptive scanning behavior. Which of the following statements describes IPS adaptive scanning?A . Determines the optimal number of IPS engines required based on system load.B . Downloads signatures on demand from FDS based on scanning requirements.C . Determines...

January 6, 2024 No Comments READ MORE +

What troubleshooting tools could an administrator use to get more information about the problem?

A FortiGate is rebooting unexpectedly without any apparent reason. What troubleshooting tools could an administrator use to get more information about the problem? (Choose two.)A . Firewall monitor.B . Policy monitor.C . Logs.D . Crashlogs.View AnswerAnswer: C,D

January 6, 2024 No Comments READ MORE +

Which two tasks are automated using the Install Wizard on FortiManager? (Choose two.)

Which two tasks are automated using the Install Wizard on FortiManager? (Choose two.)A . Installing configuration changes to managed devicesB . Importing interface mappings from managed devicesC . Adding devices to FortiManagerD . Previewing pending configuration changes for managed devicesView AnswerAnswer: A,D Explanation: Reference: https://docs.fortinet.com/document/fortimanager/6.2.0/administration-guide/668612/using-the-install-wizard-to-install-device-settings-only

January 6, 2024 No Comments READ MORE +

What can the administrator do to fix this problem?

An administrator has configured two FortiGate devices for an HA cluster. While testing HA failover, the administrator notices that some of the switches in the network continue to send traffic to the former primary device. What can the administrator do to fix this problem?A . Configure remote link monitoring to...

January 5, 2024 No Comments READ MORE +