Why didn’t the tunnel come up?

View the exhibit, which contains the partial output of an IKE real-time debug, and then answer the question below. Why didn’t the tunnel come up?A . The pre-shared keys do not match. B. The remote gateway’s phase 2 configuration does not match the local gateway’s phase 2 configuration. C. The...

September 16, 2022 No Comments READ MORE +

Which statements are true regarding the Weight value?

View the exhibit, which contains the output of a diagnose command, and the answer the question below. Which statements are true regarding the Weight value?A . Its initial value is calculated based on the round trip delay (RTT). B. Its initial value is statically set to 10. C. Its value...

September 15, 2022 No Comments READ MORE +

Which of the following statements about the exhibit are true?

View the exhibit, which contains the output of a BGP debug command, and then answer the question below. Which of the following statements about the exhibit are true? (Choose two.)A . For the peer 10.125.0.60, the BGP state of is Established. B. The local BGP peer has received a total...

September 15, 2022 No Comments READ MORE +

Which statement about memory conserve mode is true?

Which statement about memory conserve mode is true?A . A FortiGate exits conserve mode when the configured memory use threshold reaches yellow. B. A FortiGate starts dropping all the new and old sessions when the configured memory use threshold reaches extreme. C. A FortiGate starts dropping new sessions when the...

September 15, 2022 No Comments READ MORE +

Which two configuration settings change the behavior for content-inspected traffic while FortiGate is in conserve mode? (Choose two.)

Which two configuration settings change the behavior for content-inspected traffic while FortiGate is in conserve mode? (Choose two.)A . IPS failopen B. mem failopen C. AV failopen D. UTM failopenView AnswerAnswer: A,C

September 15, 2022 No Comments READ MORE +

What must the administrator change to fix the issue?

Refer to the exhibit, which shows a FortiGate configuration. An administrator is troubleshooting a web filter issue on FortiGate. The administrator has configured a web filter profile and applied it to a policy; however, the web filter is not inspecting any traffic that is passing through the policy. What must...

September 14, 2022 No Comments READ MORE +

Under normal operation, how many OSPF full adjacencies are formed to each of the other two units?

Four FortiGate devices configured for OSPF connected to the same broadcast domain. The first unit is elected as the designated router. The second unit is elected as the backup designated router. Under normal operation, how many OSPF full adjacencies are formed to each of the other two units?A . 1...

September 14, 2022 No Comments READ MORE +

Assuming all the appropriate firewall policies are configured, which of the following pings will FortiGate route?

View the exhibit, which contains a partial routing table, and then answer the question below. Assuming all the appropriate firewall policies are configured, which of the following pings will FortiGate route? (Choose two.)A . Source IP address 10.1.0.24, Destination IP address 10.72.3.20. B. Source IP address 10.72.3.27, Destination IP address...

September 14, 2022 No Comments READ MORE +

What OSPF configuration settings must match in both VDOMs to have the OSPF adjacency successfully forming?

An administrator has configured a FortiGate device with two VDOMs: root and internal. The administrator has also created and inter-VDOM link that connects both VDOMs. The objective is to have each VDOM advertise some routes to the other VDOM via OSPF through the inter-VDOM link . What OSPF configuration settings...

September 13, 2022 No Comments READ MORE +

Why didn’t the script make any changes to the managed device?

An administrator has configured the following CLI script on FortiManager, which failed to apply any changes to the managed device after being executed. Why didn’t the script make any changes to the managed device?A . Commands that start with the # sign are not executed. B. CLI scripts will add...

September 13, 2022 No Comments READ MORE +