Fortinet NSE7_NST-7.2 Fortinet NSE 7 – Network Security 7.2 Support Engineer Online Training
Fortinet NSE7_NST-7.2 Online Training
The questions for NSE7_NST-7.2 were last updated at Nov 19,2024.
- Exam Code: NSE7_NST-7.2
- Exam Name: Fortinet NSE 7 - Network Security 7.2 Support Engineer
- Certification Provider: Fortinet
- Latest update: Nov 19,2024
Refer to the exhibit, which shows the omitted output of a real-time OSPF debug
Which statement is false?
- A . A password has been configured on the local OSPF router but is not shown in the output
- B . The Hello packet is being sent from an OSPF router with ID 0.0.0.112.
- C . The two FortiGate devices attempting adjacency are in area 0.0.0.0.
- D . One FortiGate device is configured to require authentication, while the other is not
Which of the following regarding protocol states is true?
- A . proto_state=00 indicates that UDP traffic flows in both directions.
- B . proto_state-01 indicates an established TCP session.
- C . proto_state=10 indicates an established TCP session.
- D . proto state=01 indicates one-way ICMP traffic.
Which statement is correct regarding LDAP authentication using the regular bind type?
- A . The regular bind type goes through four steps to successfully authenticate a user.
- B . The regular bind type cannot be used if users are authenticated using sAMAccountName.
- C . The regular bind type is the easiest bind type to configure on FortiOS.
- D . The regular bind type requires a FortiGate super_admin account.
Refer to the exhibit.
FortiGate has already been configured with a firewall policy that allows all ICMP traffic to flow from port1 to port3.
Which changes must the administrator perform to ensure the server at 10.4.0.1/24 receives the echo reply from the laptop at 10.1.0.1/24?
- A . Enable asymmetric routing under config system settings.
- B . Modify the default gateway on the laptop from 10.1.0.2 to 10.2.0.2
- C . A firewall policy that allows all ICMP traffic from port3 to port1.
- D . Change the configuration from strict RPF check mode to feasible RPF check mode
Which two conditions would prevent a static route from being added to the routing table? (Choose two.)
- A . The next-hop IP address is unreachable.
- B . The interface specified in the route configuration is down
- C . The route has a lower priority value than another route to the same destination.
- D . There is another other route to the same destination, with a lower distance.
Refer to the exhibit, which shows a truncated output of a real-time RADIUS debug.
Which two statements are true? (Choose two.)
- A . The RADIUS server queried for authentication is located at IP address 172.25.188.164.
- B . Authentication was unsuccessful.
- C . The authentication scheme used was pop3.
- D . Authentication was successful
- E . Two-factor authentication was required.
Which three conditions are required for two FortiGate devices to form an OSPF adjacency? (Choose three.)
- A . OSPF link costs match.
- B . OSPF interface priority settings are unique
- C . OSPF interface network types match
- D . Authentication settings match.
- E . OSPF router IDs are unique.
Refer to the exhibit, which contains the partial output of a diagnose command.
Based on the output, which two statements are correct? (Choose two.)
- A . The remote gateway IP is 10.200.5.1.
- B . The remote gateway has quick more selectors containing a destination subnet of 10.1.2.0/24.
- C . DPD is disabled.
- D . Anti-replay is enabled.
Refer to the exhibit, which shows a session table entry.
Which statement about FortiGate behavior relating to this session is true?
- A . FortiGate forwarded this session without any inspection.
- B . FortiGate is performing a security profile inspection using the CPU.
- C . FortiGate redirected the client to the captive portal to authenticate, so that a correct policy match could be made.
- D . FortiGate applied only IPS inspection to this session.
What is the diagnose test application ipsmonitor 5 command used for?
- A . To disable the IPS engine
- B . To provide information regarding IPS sessions
- C . To restart all IPS engines and monitors
- D . To enable IPS bypass mode
Latest NSE7_NST-7.2 Dumps Valid Version with 40 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
