Fortinet FCP_FWF_AD-7.4 FCP – Secure Wireless LAN 7.4 Administrator Online Training
Fortinet FCP_FWF_AD-7.4 Online Training
The questions for FCP_FWF_AD-7.4 were last updated at Feb 22,2025.
- Exam Code: FCP_FWF_AD-7.4
- Exam Name: FCP - Secure Wireless LAN 7.4 Administrator
- Certification Provider: Fortinet
- Latest update: Feb 22,2025
You are investigating a wireless performance issue and you are trying to audit the neighboring APs in the PF environment. You review the Rogue APs widget on the GUI but it is empty, despite the known presence of other APs.
Which configuration change will allow neighboring APs to be successfully detected?
- A . Enable Locate WiFi clients when not connected in the relevant AP profiles.
- B . Enable Monitor channel utilization on the relevant AP profiles.
- C . Ensure that all allowed channels are enabled for the AP radios.
- D . Enable Radio resource provisioning on the relevant AP profiles.
You have just authorized a newly added FortiAP device on FortiGate. It went offline for an extended time without coming back online again.
What troubleshooting process must you take to bring FortiAP back online?
- A . Access FortiAP management using HTTPs.
- B . Verify that communication between FortiAP and the wireless controller is not blocked.
- C . Restart the wireless controller if it is unresponsive for the newly added FortiAP device.
- D . Check the power feed to the FortiAP device and PoE status if powered by a switch.
Which of the following features distinguishes FortiPresence from FortiPlanner?
- A . FortiPresence is used primarily for network threat detection.
- B . FortiPresence provides analytics solutions.
- C . FortiPlanner is used as a wireless controller.
- D . FortiPlanner is a cloud-based deployment tool.
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A . DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
- B . DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
- C . DARRP measurements can be scheduled to occur at specific times.
- D . DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
Which of the following are considered wireless security options?
- A . WPA3 encryption
- B . Rogue AP scanning
- C . Firmware updating
- D . SSID hiding
What configurations can be applied through FortiAP profiles to manage FortiAP devices? (Select all that apply)
- A . Advanced wireless settings
- B . SSID hiding
- C . VLAN configurations
- D . Client load balancing
As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?
- A . Set the wireless controller country setting
- B . Create a custom AP profile
- C . Preauthorize APs
- D . Create wireless LAN specific policies
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)
- A . Hardware security token authentication
- B . Short message service authentication
- C . Software security token authentication
- D . Social networks authentication
WIDS profiles are primarily used for:
- A . Deploying firmware updates to APs.
- B . Wireless Intrusion Detection System configurations.
- C . Enhancing Wi-Fi signal strength.
- D . Assigning IP addresses to wireless clients.
Part of the location service registration process is to link FortiAPs in FortiPresence.
Which two management services can configure the discovered AP registration information from the FortiPresence cloud? (Choose two.)
- A . AP Manager
- B . FortiAP Cloud
- C . FortiSwitch
- D . FortiGate
Latest FCP_FWF_AD-7.4 Dumps Valid Version with 150 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
