A new RecoverPoint/SE environment has been installed with a single cluster. There are no limitations regarding journal sizes and you want to choose how frequently RecoverPoint can create point-in-time copies.
What is the highest frequency available for point-in-time copies in this environment?
- A . One per I/O
- B . One per sec.
- C . One per 500 µsec.
- D . One per 500 msec.
Which RecoverPoint product(s) may be licensed by the amount of array capacity?
- A . RecoverPoint/EX only
- B . RecoverPoint/CL only
- C . RecoverPoint/SE
- D . RecoverPoint/EX and RecoverPoint/CL
What is the maximum supported storage capacity, per license, for an EMC RecoverPoint/EX environment?
- A . 100 terabytes
- B . 2 petabytes
- C . 4 petabytes
- D . 10 petabytes
What is the maximum number of clusters supported in an EMC RecoverPoint/CL environment?
- A . 2
- B . 3
- C . 4
- D . 5
In a EMC RecoverPoint environment, which EMC product adds support for heterogeneous storage systems?
- A . VPLEX
- B . VNX/CX
- C . VMAX
- D . Isilon
Which EMC storage technologies are supported with EMC RecoverPoint?
- A . VNX, VMAX, and VPLEX
- B . VNX, Data Domain, and Isilon
- C . VMAX, VPLEX, and Data Domain
- D . VPLEX, Isilon, and VNX
What is the maximum number of copies of production data supported with RecoverPoint?
- A . Four remote copies
- B . One local copy and four remote copies
- C . Two remote copies
- D . Two local copies and two remote copies
There is one instance of RecoverPoint/CL installed that is protecting data within a data center.
What is the maximum number of additional clusters that can be added to this configuration?
- A . 1
- B . 2
- C . 4
- D . 5
Your business is planning to deploy RecoverPoint for your DR solution.
What is an important consideration when using Consistency Groups in RecoverPoint 4.1?
- A . Supports up to two synchronous copies per Consistency Group
- B . Supports up to three remote copies in a same remote cluster
- C . Fibre connectivity is required for synchronous replication
- D . Supports host-based and array-based write splitters
Which Ethernet interface on an RPA is used for replication to the remote clusters?
- A . eth0
- B . eth1
- C . eth2
- D . eth3
Which Ethernet interface on an RPA is used for management?
- A . eth0
- B . eth1
- C . eth2
- D . eth3
Through what does RecoverPoint support heterogeneous storage environments?
- A . VPLEX
- B . Any array-based splitter
- C . APIs
- D . VMAX splitter only
Which virtualization solution components are supported by RecoverPoint?
- A . Hyper-V, VMware vCenter monitoring, VMware SRM
- B . Hyper-V only
- C . VMware vCenter monitoring only
- D . VMware SRM only
What is the maximum number of copies supported using the MetroPoint topology for VPLEX continuous data replication?
- A . 3
- B . 4
- C . 5
- D . 8
Which protocol does the vRPA use to access the journal volumes?
- A . iSCSI
- B . FC
- C . IP
- D . FCoE
A company is using an EMC VNX storage array. RecoverPoint is being configured to replicate to a DR site.
RP will be protecting three datastores:
– A thick 100 GB LUN containing 60 GB of data
– A thin 50 GB LUN containing 15 GB of data
– A thick 75 GB LUN containing 75 GB of data
How much of the user data is being replicated to the DR site?
- A . 150
- B . 185
- C . 190
- D . 225
What is the maximum number of RPA clusters allowed in a RecoverPoint/SE configuration?
- A . 1
- B . 2
- C . 4
- D . 5
Which RecoverPoint feature requires the production copy to be located on a VNX?
- A . Snap-based Replication
- B . Deduplication
- C . Synchronous replication
- D . Distributed Consistency Groups
Snap-based Replication requires the production volume of a Consistency Group to be on which array type?
- A . VNX
- B . VMAX
- C . VPLEX
- D . Isilon
A storage administrator has been tasked to demonstrate the image access capability of RecoverPoint.
Which RecoverPoint option should they use?
- A . Test a Copy
- B . Fail Over
- C . Fail Back
- D . Recover Production
A RecoverPoint cluster contains a Consistency Group with one remote copy.
Which volume can be used to verify that snapshots are being created?
- A . Remote copy
- B . Production copy
- C . Repository
- D . Snap copy
Which RecoverPoint features are supported on physical and virtual RPAs?
- A . Deduplication, SRM integration, and Snapshot-Based Replication
- B . Distributed CGs, Deduplication, and SRM integration
- C . SRM integration, Snapshot-Based Replication, and Distributed CGs
- D . Snapshot-Based Replication, Distributed CGs, and Deduplication
What is the minimum number of RecoverPoint Clusters required to use the MetroPoint feature?
- A . 1
- B . 2
- C . 3
- D . 5
A company recently acquired a new DR site and requires local Fibre Channel based production data to be replicated synchronously. They are investigating what infrastructure is needed on this DR site.
What is an important connectivity consideration?
- A . Site-to-site connectivity can be based on IP.
- B . Site-to-site connectivity requires Fibre Channel.
- C . Site-to-site connectivity requires FCIP.
- D . Maximum synchronous replication speed is 400 MBps.
A company recently acquired a new DR site and requires their production data to be replicated to this DR site.
What is an important consideration about the RecoverPoint out-of-band architecture?
- A . Performance on the production site is not impacted.
- B . Site-to-site connectivity needs to be based on Fibre Channel.
- C . Maximum asynchronous replication speed is 400 MBps.
- D . Maximum synchronous replication speed is 400 Mbps.
An existing RecoverPoint/CL environment consists of one cluster at the main office and two off-site DR clusters. You have been asked to expand the environment to the maximum number of DR sites using RecoverPoint.
How many additional clusters could be added to this RecoverPoint Environment?
- A . 2
- B . 4
- C . 5
- D . 8
An existing RecoverPoint/CL environment consists of one cluster at the main office and one off-site DR cluster. You have been asked to expand the environment to the maximum number of DR sites using RecoverPoint.
How many additional clusters could be added to this RecoverPoint Environment?
- A . 2
- B . 3
- C . 4
- D . 5
Which RecoverPoint family is licensed per array and array capacity?
- A . RecoverPoint/EX only
- B . RecoverPoint/SE
- C . RecoverPoint/CL only
- D . RecoverPoint/EX and RecoverPoint/CL
What are the minimum RecoverPoint and VPLEX versions that support MetroPoint?
- A . RecoverPoint 4.1 and GeoSynchrony 5.4
- B . RecoverPoint 4.0 and GeoSynchrony 5.3
- C . RecoverPoint 4.1 and GeoSynchrony 5.3
- D . RecoverPoint 4.0 and GeoSynchrony 5.4
What are key use cases for RecoverPoint?
- A . Disaster Recovery, Operational Recovery, and Data Migration
- B . Disaster Recovery and Operational Recovery only
- C . Disaster Recovery and Data Migration only
- D . High Availability Solution Implementation
An existing RecoverPoint cluster has four physical RPAs deployed with VMAX arrays.
Which RPAs need to be masked to the VMAX gatekeepers in order to deploy the VMAX splitter?
- A . RPA 1 and RPA 2
- B . RPA 1 only
- C . All RPAs in the cluster
- D . RPA 2 only
A customer is installing a new RecoverPoint environment. All RPAs have been racked, cabled, and powered on. You have chosen to automatically discover the RPAs using Deployment Manager. After running the discovery, no RPAs are found.
What is the most likely cause of this issue?
- A . No DHCP server on the network
- B . Port 443 not open on the network
- C . RecoverPoint/SE wizard selected
- D . RPAs not configured into a cluster
You are adding a VMAX array to a RecoverPoint/CL environment.
What needs to be done?
- A . Verify there is a zone that includes the RPA ports and the same VMAX front end ports that are zoned to the production host initiator.
- B . Verify that the 16 new gatekeepers are in the same storage group as the repository and journals. Add the RPA initiator and port groups to the masking view.
- C . After setting up the masking view use boxmgmt to log in to one of the site leader RPAs and be sure to tag all volumes that RecoverPoint is masked to C including the production and copy volumes.
- D . Verify that the VMAX is at Enginuity microcode 5876 or higher. After doing the LUN masking, enable Write-Protect ByPass (WPBP). Ensure that the proper license for the VMAX is installed on the RPAs.
A customer has three VMAX arrays and one VNX array fronted by an EMC VPLEX. They want to use RecoverPoint to protect their environment.
How many licenses, of which type, would be required for their environment?
- A . 1 EX license only
- B . 4 EX licenses
- C . 5 EX licenses
- D . 1 SE license and 1 EX license
A customer has two VMAX arrays and three VNX arrays fronted by an EMC VPLEX. They wish to use RecoverPoint to protect their environment.
How many licenses, and of which type, would be required for their environment?
- A . 1 EX license
- B . 1 SE license and 2 EX licenses
- C . 5 EX licenses
- D . 6 EX licenses
Which connectivity protocols are used to interconnect RecoverPoint clusters?
- A . FC and IP
- B . FC and iSCSI
- C . FC and FCoE
- D . FCoE and IP
What information is required to connect a new RecoverPoint cluster to an existing one?
- A . WAN IP address and internal cluster name
- B . RPA serial ID
- C . Site ID and Management IP address
- D . Internal cluster name only
You are installing RecoverPoint/SE, and have selected the automatic zoning option. There are four VNX ports in each fabric.
How many zones are automatically created on each fabric for a two-node RPA cluster?
- A . 2
- B . 3
- C . 4
- D . 5
When using Deployment Manager to install RecoverPoint/SE, which zoning methods are available with Brocade switches?
- A . Automatic and Manual
- B . Manual and Semi-automatic
- C . Automatic and Semi-automatic
- D . Automatic and Virtual
What must be installed on the VNX prior to deploying the RecoverPoint Write splitter?
- A . RecoverPoint Splitter Enabler only
- B . RecoverPoint Driver and RecoverPoint Splitter Enabler
- C . RecoverPoint License
- D . Unisphere Service Manager
You are responsible for installing a four-node RPA cluster. All RPAs are powered on. Both the FC and IP networks are connected, zoned, and routed properly. The RPAs are loaded with the latest image and IP addresses are set. However, Deployment Manager cannot discover RPAs.
What is a possible cause?
- A . Port 22 not open between host running Deployment Manager and RPAs
- B . Deployment Manager host and RPAs on different subnets
- C . DHCP not used to set IP addresses for RPAs
- D . RPAs not installed separately using Deployment Manager
When choosing a journal for a CG what would be a factor in selecting which LUNs to use?
- A . Volumes that are all close to the same size
- B . Volumes masked to the production host
- C . Any volume less than 10 GB
- D . Only thin LUNs
After expanding to include an additional existing RecoverPoint cluster you use Deployment Manager to connect the clusters, but it fails.
What might be the problem?
- A . New cluster is already licensed
- B . RPAs at second cluster are not same type
- C . Second cluster not yet added to Repository
- D . No splitter added to second cluster
After expanding to include an additional existing RecoverPoint cluster you use Deployment Manager to connect the clusters, but it fails.
What might be the problem?
- A . New cluster has existing Consistency Group
- B . RPAs at second cluster are not same type
- C . Second cluster not yet added to the Repository
- D . No splitter added to second cluster
A new RecoverPoint system is being installed and the RPAs need to be upgraded to the latest version.
How should this be done?
- A . Choose the option to upgrade the RPA version from an ISO while installing RecoverPoint using Deployment Manager.
- B . Before doing the install ensure all the RPAs IP addresses reach each other. Connect to RPA1 with boxmgmt and do the upgrade.
- C . Install the new system with Deployment Manager and then log in as boxmgmt and perform the upgrade on one RPA.
- D . Upgrade the RPAs to the latest version first; otherwise Deployment Manager will prevent the installation.
After installing two RecoverPoint clusters you find that a Consistency Group cannot be configured with a remote copy.
Why?
- A . Deployment Manager was not used to connect the clusters.
- B . The RPAs at the second cluster are not the same type (virtual vs physical).
- C . The second cluster has not yet been added to the Repository.
- D . There is no splitter added to the second cluster.
A customer is interested in implementing a RecoverPoint solution using a four-node cluster with physical RPAs.
How many total IP addresses are required for the cluster?
- A . 4
- B . 5
- C . 8
- D . 9
A customer wants to implement a two-node RecoverPoint solution with local replication. How many IP addresses are required for each cluster?
- A . 2
- B . 3
- C . 4
- D . 5
A customer environment includes a two-cluster RecoverPoint/SE instance. They have a new data center 100 km away that they wish to protect with RecoverPoint.
What steps are required to connect a new cluster to their existing RecoverPoint instance?
- A . Use Deployment Manager to convert the existing instance to RP/EX. Use Deployment Manager to connect the new cluster to the existing instance. Install RP/EX licenses for their existing arrays.
- B . Use Deployment Manager to connect the new cluster to the existing instance.
- C . Install RP/SE licenses for their existing arrays. Install RP/SE licenses for the new cluster. Use Deployment Manager to connect the new cluster to the existing instance.
- D . Install RP/CL licenses for their existing cluster. Use Deployment Manager to connect the new cluster to the existing instance.
A customer environment includes a two-cluster RecoverPoint/SE instance. They have a new data center 500 km away that they wish to protect with RecoverPoint.
What steps are required to connect a new cluster to their existing RecoverPoint instance?
- A . Use Deployment Manager to convert the existing instance to RP/EX. Use Deployment Manager to connect the new cluster to the existing instance. Install RP/EX licenses for their existing arrays.
- B . Use Deployment Manager to connect the new cluster to the existing instance.
- C . Install RP/SE licenses for their existing arrays. Install RP/SE licenses for the new cluster. Use Deployment Manager to connect the new cluster to the existing instance.
- D . Install RP/CL licenses for their existing cluster. Use Deployment Manager to connect the new cluster to the existing instance.
You are adding an RPA to a cluster using Deployment Manager.
What requirement must be satisfied before proceeding?
- A . Zoning and LUN masking must be known to be identical to the existing RPAs in the cluster.
- B . RPA iSCSI configuration settings must be known. All other zoning and LUN masking settings will automatically be read from the existing RPA site leader.
- C . RPA and array iSCSI configuration settings must be known. All other zoning and LUN masking settings will automatically be read from the existing RPA site leader.
- D . RPA and Storage iSCSI configuration settings will automatically be read from the cluster.
Which RecoverPoint tool is used for system conversions?
- A . Deployment Manager
- B . Unisphere for RecoverPoint
- C . SolVe Desktop
- D . BCSD Sizing
You are implementing a RecoverPoint/SE cluster using vRPAs.
What must be configured and available on the new VNX array prior to the installation of the cluster with Deployment Manager?
- A . An iSCSI interface from SPA and SPB of the VNX
- B . Zones from SPA and SPB FC ports to the ESX servers
- C . Zones from SPA and SPB FC ports to the Virtual WWNs of the vRPAs
- D . Physical connections from the ESX HBAs to the FC interfaces of SPA and SPB
A RecoverPoint/SE cluster is using vRPAs. A second cluster needs to be connected.
Which RPA type must be used at the new cluster?
- A . Virtual or Physical
- B . Virtual only
- C . Generation 5
- D . Physical only
A customer is evaluating the deployment of RecoverPoint with their VMAX array. They want to deploy the RPAs in the virtual appliance form. They ask your opinion about using vRPA versus physical appliances.
What should you advise them?
- A . They can only use physical RPAs in the current environment.
- B . For performance reasons, they can mix vRPAs and physical RPAs in the same RPA cluster, but only at remote sites.
- C . For performance reasons, they cannot mix physical and vRPAs within an RPA cluster.
- D . They can mix vRPA and physical RPAs in the same RPA cluster at all sites.
A customer is evaluating the deployment of RecoverPoint with their VNX array. They want to deploy the RPAs in virtual appliance form. They ask your opinion about using vRPA versus physical appliances.
What should you advise them?
- A . They cannot mix physical and virtual RPAs within their RPA cluster.
- B . For performance reasons, they can mix vRPAs and physical RPAs in the remote RPA cluster.
- C . vRPAs cannot be used in a VNX environment.
- D . They can mix vRPA and physical RPAs in the same RPA cluster at all sites.
A customer is installing a single cluster RecoverPoint/SE environment and has decided to create a cluster of six virtual RPAs to perform RecoverPoint operations.
According to EMC best practices, how many ESX hosts are needed to host the required vRPAs?
- A . 2
- B . 3
- C . 4
- D . 6
A customer environment uses VMAX arrays for production storage. The customer wants to implement RecoverPoint for data protection. Having researched vRPAs, they want to use this technology as well.
What should you advise them?
- A . vRPAs are only supported with VNX arrays
- B . Add iSCSI interfaces to their VMAX arrays
- C . Use vRPAs with FC connections to the SAN
- D . Implement FCoE for connections from the vRPAs
What is a prerequisite for deploying a RecoverPoint/SE system?
- A . VNX splitter enabled
- B . RecoverPoint/SE license installed
- C . RecoverPoint/SE registered with EMC
- D . Unisphere for RecoverPoint installed and running
When selecting the semi-automatic zoning method while installing RecoverPoint/SE, which zones are displayed per RPA?
- A . One RPA HBA zoned to SP-A One RPA HBA zoned to SP-B All RPA HBAs zoned to each other
- B . All RPA HBAs zoned to SP-A All RPA HBAs zoned to SP-B All RPA HBAs zoned to each other
- C . All RPA HBAs zoned to SP-A All RPA HBAs zoned to SP-B One RPA HBA zoned to multiple HBA ports on each of the other RPAs in the cluster
- D . One RPA HBA zoned to SP-A One RPA HBA zoned to SP-B One RPA HBA zoned to a single HBA on each of the other RPAs in the cluster
Which statement is true regarding vRPAs?
- A . vRPAs are deployed using the OVA template.
- B . The proper license must be installed before vRPA deployment.
- C . vRPAs can be connected to storage through the VNX splitter in the RecoverPoint/SE system.
- D . vRPAs are installed using Unisphere for RecoverPoint.
Which statement is true regarding vRPAs?
- A . vCenter Server is required to deploy vRPAs.
- B . The proper license must be installed before vRPA deployment.
- C . vRPAs can be connected to storage through the VNX splitter in the RecoverPoint/SE system.
- D . vRPAs are installed using Unisphere for RecoverPoint.
Which Unisphere for RecoverPoint view displays both the system traffic and Consistency Group status?
- A . RecoverPoint Dashboard
- B . Recovery
- C . RPA Clusters
- D . Admin
In the Recovery tab of Unisphere for RecoverPoint, which option is used to temporarily mount an image?
- A . Test a Copy
- B . Enable Image Access
- C . Manage Recovery
- D . Enable Direct Access
After selecting a cluster in the RPA Clusters tab, which option can display alerts that have been logged for any of the physical components of the RecoverPoint system in that cluster?
- A . General Cluster Info
- B . Overall Health
- C . System Events
- D . System Notifications
In Unisphere for RecoverPoint, where should a user navigate in order to collect logs for support purposes?
- A . Admin Tab > System Analysis Tools > Collect System Information
- B . Admin Tab > System Notifications > Configure System Reports and Alerts
- C . Dashboard Tab > System Analysis Tools > Detect Bottlenecks
- D . Admin Tab > RPA Clusters > Export Consolidated Statistics
The Getting Started wizard that is displayed the first time a user accesses Unisphere for RecoverPoint assists with performing what action?
- A . Adding licenses
- B . Adding splitters
- C . Configuring RPAs
- D . Creating Consistency Groups
System events can be copied to the clipboard from which Unisphere for RecoverPoint view?
- A . RecoverPoint Dashboard
- B . Recovery
- C . RPA Clusters
- D . Admin
When logging into an unattached RecoverPoint appliance for the first time, which username and password combination must be used?
- A . usernamE.boxmgmt passworD.boxmgmt
- B . usernamE.admin passworD.Mi@Dim7T
- C . usernamE.admin passworD.admin
- D . usernamE.service passworD.service
You are working on a RecoverPoint local replication solution in an environment that includes VNX and VMAX storage arrays. You want to create a Consistency Group (CG) for your Oracle database. However, some of the database volumes are located in the VNX and others are located in the VMAX.
What is the recommended management solution?
- A . Create one CG using VNX and VMAX volumes
- B . Create a new RecoverPoint cluster and add the VNX splitter
- C . Migrate all LUNs to the VMAX
- D . Create two CGs: one for VNX volumes and another for VMAX volumes
Which journal action available in Unisphere for RecoverPoint will NOT result in a full sweep synchronization and the loss of all history in the existing journal?
- A . Add a journal volume
- B . Remove a journal volume
- C . Expand a journal volume
- D . Reduce a journal volume
In order to create a new Consistency Group, a user should navigate to which option within the Protection tab of Unisphere for RecoverPoint?
- A . Protect Volumes
- B . Manage Protection
- C . Deployment Manager
- D . Group Sets
A company has a DR site connected using a 4 Gbps FC link and two RPAs on the primary site, and two RPAs at the DR site. They are experiencing high load events although the FC link is not fully utilized.
What would be the best solution to get the FC link utilization up as high as possible?
- A . Add two RPAs to the primary site and add two RPAs to the DR site
- B . Add two RPAs to the primary site only
- C . Use distributed consistency groups with one primary RPA and two secondary RPAs on the primary site
- D . Add two RPAs to the DR site only
Which RecoverPoint feature allows the protection of volumes on both sides of a VPLEX Metro Cluster?
- A . MetroPoint
- B . Continuous Remote Replication
- C . Distributed Consistency Groups
- D . Group Sets
A storage administrator has an implementation with 40 Consistency Groups (CGs). They need to create distributed CGs.
What is the maximum number of distributed CGs that can be added to this particular system?
- A . 8
- B . 16
- C . 24
- D . 128
A storage administrator has a RecoverPoint environment with vRPAs containing 64 Consistency Groups (CGs). They want to create distributed CGs.
What is the maximum number of distributed CGs that can be added to this particular system?
- A . 0
- B . 8
- C . 40
- D . 128
You are protecting a volume using the wizard in Unisphere for RecoverPoint.
Which state will the new Consistency Group be in immediately after completing the wizard?
- A . Initializing
- B . Active
- C . Paused
- D . Disabled
What is used when more performance is needed than a single RPA can provide for asynchronous replication?
- A . Distributed Consistency Groups
- B . Journal compression
- C . Fibre Channel connections
- D . Multi-cluster copies
What is the minimum size of the journal when using Distributed Consistency Groups?
- A . 5 GB
- B . 20 GB
- C . 40 GB
- D . 60 GB
A company with a DR site connected with a 2 Gbps FC link has three RPAs at each site. They are experiencing High Load events, although the FC link is not fully utilized.
What would be the best solution to get the FC link utilization up as high as possible while mitigating those events?
- A . Use a Distributed Consistency Group
- B . Add one RPA to the Primary site
- C . Use the Consistency Group on both RPAs and add two RPAs to the secondary site
- D . Add one RPA to the DR site
A company with a DR site connected with a 2 Gbps FC link has three vRPAs at each site. They are experiencing High Load events, although the FC link is not fully utilized.
What would be the best solution to get the FC link utilization up as high as possible while mitigating those events?
- A . Replace the vRPAs with physical RPAs and start using a Distributed Consistency Group
- B . Add two more vRPAs to the Primary site and divide the Consistency Group into four segments
- C . Divide the Consistency Group into two segments and start using Distributed Consistency Groups
- D . Add two RPAs to the Primary site as well as the secondary site
What should be used when more performance is needed than a single RPA can provide for asynchronous replication?
- A . Distributed Consistency Groups
- B . Journal Compression
- C . Fibre Channel connections
- D . Multi-Cluster copies
You are protecting a volume using the wizard in Unisphere for RecoverPoint.
Which state will the new Consistency Group be in immediately after completing the wizard?
- A . Initializing
- B . Active
- C . Paused
- D . Disabled
Which FA ports must the production LUN be mapped to in order to perform write splitting using the VMAX splitter?
- A . The ports zoned to both the Host and the RPAs only
- B . Every available port; the RPAs access the VMAX through the gatekeepers
- C . The ports zoned to the Production Host only
- D . The ports zoned to the RPAs only
A Consistency Group consists of one production copy, one local copy, and two remote copies.
How many journals are required for this configuration?
- A . Four in total
- B . Two in total
- C . One for each remote copy and one for the local copy
- D . One for the production and one for each remote copy
You are creating a Consistency Group with the Protect Volumes wizard in a RecoverPoint/EX environment.
What LUNs are displayed in the list generated by the wizard?
- A . LUNs masked to the RPAs
- B . LUNs configured on the licensed array
- C . LUNs attached to the splitter
- D . LUNs masked to the production host
What is a named point-in-time copy of data marked by the system for recovery purposes within RecoverPoint?
- A . Bookmark
- B . Snapshot
- C . Image Access Point
- D . Journal
What is the first operation involved in the RecoverPoint Initialization process?
- A . Production and replica volumes are divided into data segments.
- B . Dirty segments of the replica volume Consistency Group are checked.
- C . Hash is created for all segments in production and replica volumes.
- D . Production and replica hashes are compared.
What is a characteristic of a full sweep?
- A . Initialization is done on all volumes in a Consistency Group.
- B . Initialization is done on specific volumes in a Consistency Group.
- C . A full sweep occurs when a user enables a disabled volume.
- D . A full sweep occurs when a user enables a disabled splitter.
What is a characteristic of a volume sweep?
- A . Initialization is done on specific volumes in a Consistency Group.
- B . Initialization is done on all volumes in a Consistency Group.
- C . A volume sweep occurs when a user enables a disabled volume.
- D . A volume sweep occurs when a user enables a disabled splitter.
How much data, at a minimum, must change in order for the snapshot consolidation process to start?
- A . 64 MB
- B . 128 MB
- C . 512 MB
- D . 1 GB
What user action causes a full sweep to occur?
- A . Enable a disabled Consistency Group
- B . Enable a disabled volume
- C . Enable a disabled splitter
- D . Attach a volume to a splitter
Which statement is true about Logged Access mode?
- A . RecoverPoint will roll back (or forward) the snapshots until the selected image is reached.
- B . RecoverPoint creates a virtual disk by pulling the needed data either from the snapshots or from the storage.
- C . RecoverPoint will retrieve the snapshot from the Image Access log.
- D . When Logged Access is disabled, all writes made to the image will be saved to the journal.
When a copy is in Image Access mode, where is the Image Access Log stored?
- A . Journal of the copy
- B . Journal of the source
- C . In memory of the RPA
- D . On the copy volume
You are a storage administrator tasked with creating a Consistency Group in a RecoverPoint/EX system. You launch the Protect Volumes wizard in Unisphere and notice that the desired production volume is not available.
What would be a possible cause?
- A . The volumes are not masked to the RPAs.
- B . The volumes are masked to a host.
- C . The journal volumes are on a non-licensed array.
- D . Consistency Groups can only be created by boxmgmt.
You are a storage administrator tasked with creating a Consistency Group in a RecoverPoint/EX system. You launch the Protect Volumes wizard in Unisphere and notice that the desired production volume is not available.
What would be a possible cause?
- A . The production volumes are on a non-licensed array.
- B . The volumes are masked to a host.
- C . The journal volumes are on a non-licensed array.
- D . Consistency Groups can only be created by boxmgmt.
Which Image Access Mode should be used when large portions of an image might be changed?
- A . Logged Access
- B . Virtual Access (without Roll)
- C . Snap Access
- D . Virtual Access (with Roll)
If you wanted to use the Roll Image in Background option to access an image, which access mode should you select?
- A . Virtual Access
- B . Logged access
- C . Direct Access
- D . Snap Access
Which image access mode provides the quickest way to access data?
- A . Virtual Access
- B . Logged Access
- C . Direct Access
- D . Snap Access
When determining the journal volume size, which parameters must be considered?
- A . Rate of change Data set to be replicated Number of snapshots to retain
- B . Rate of change Percentage of sequential writes RPO/RTO
- C . Number of snapshots to retain Rate of change Consistency Group type
- D . Number of Consistency Groups RPO/RTO Network type