DELL EMC D-PVM-OE-01 Dell PowerMax Operate v2 Exam Online Training

Question #40

An engineer wants to create a 4-node cluster after rack and stack.

What port must they use to start the installation?

A . COM
B . FE
C . BE
D . iDRAC

Correct Answer: D
D

Explanation:

When an engineer wants to create a 4-node cluster after rack and stack, they must use the iDRAC (Integrated Dell Remote Access Controller) port to start the installation.

Understanding iDRAC:

Remote Management:

iDRAC provides out-of-band management capabilities, allowing administrators to manage and

monitor nodes remotely.

Virtual Console Access:

Offers a virtual console for accessing the node’s BIOS and performing installations.

Initial Cluster Setup with iDRAC:

Accessing the Node:

Connect to each node’s iDRAC interface using its IP address.

Starting the Installation:

Use the iDRAC virtual console to interact with the node as if you were physically present.

Benefits:

No need for physical access to the COM port or direct console connections.

Allows for remote configuration and reduces the time required for setup.

Why iDRAC is Used Over Other Ports:

COM Port:

The COM (serial) port can be used for initial setup, but it requires physical access and serial cables.

Less convenient compared to iDRAC’s remote capabilities.

FE (Front-End) and BE (Back-End) Ports:

FE and BE ports are used for data network connections, not for initial setup or management.

The initial configuration cannot be performed through these ports.

Procedure for Using iDRAC:

Step 1: Connect to iDRAC

Ensure that iDRAC network interfaces are connected and configured with IP addresses.

Access iDRAC via a web browser using the IP address.

Step 2: Launch Virtual Console

Log in to the iDRAC interface.

Launch the virtual console to access the node’s system interface.

Step 3: Perform Initial Configuration

Use the virtual console to run the OneFS installation wizard. Configure cluster settings, networking, and other parameters. Dell PowerScale Best Practices: Using iDRAC for Installation:

Recommended for its convenience and efficiency.

Allows for consistent setup procedures across multiple nodes.

Network Preparation:

Ensure iDRAC interfaces are properly connected to the management network.

Verify network settings to allow access from the engineer’s workstation.

Dell PowerScale

Reference: Dell EMC PowerScale OneFS Installation Guide:

Provides detailed steps on installing OneFS using iDRAC.

Dell EMC PowerScale Networking Guide:

Discusses management network configurations, including iDRAC setup.

Dell EMC iDRAC User’s Guide:

Offers comprehensive information on using iDRAC features.

Knowledge Base Articles:

Article ID 000125678: "Initial Cluster Configuration Using iDRAC"

Article ID 000125679: "Best Practices for Remote Installation on PowerScale Nodes"

Question #40

An engineer wants to create a 4-node cluster after rack and stack.

What port must they use to start the installation?

A . COM
B . FE
C . BE
D . iDRAC

Reveal Solution Hide Solution

Correct Answer: D
D

Explanation:

When an engineer wants to create a 4-node cluster after rack and stack, they must use the iDRAC (Integrated Dell Remote Access Controller) port to start the installation.

Understanding iDRAC:

Remote Management:

iDRAC provides out-of-band management capabilities, allowing administrators to manage and

monitor nodes remotely.

Virtual Console Access:

Offers a virtual console for accessing the node’s BIOS and performing installations.

Initial Cluster Setup with iDRAC:

Accessing the Node:

Connect to each node’s iDRAC interface using its IP address.

Starting the Installation:

Use the iDRAC virtual console to interact with the node as if you were physically present.

Benefits:

No need for physical access to the COM port or direct console connections.

Allows for remote configuration and reduces the time required for setup.

Why iDRAC is Used Over Other Ports:

COM Port:

The COM (serial) port can be used for initial setup, but it requires physical access and serial cables.

Less convenient compared to iDRAC’s remote capabilities.

FE (Front-End) and BE (Back-End) Ports:

FE and BE ports are used for data network connections, not for initial setup or management.

The initial configuration cannot be performed through these ports.

Procedure for Using iDRAC:

Step 1: Connect to iDRAC

Ensure that iDRAC network interfaces are connected and configured with IP addresses.

Access iDRAC via a web browser using the IP address.

Step 2: Launch Virtual Console

Log in to the iDRAC interface.

Launch the virtual console to access the node’s system interface.

Step 3: Perform Initial Configuration

Use the virtual console to run the OneFS installation wizard. Configure cluster settings, networking, and other parameters. Dell PowerScale Best Practices: Using iDRAC for Installation:

Recommended for its convenience and efficiency.

Allows for consistent setup procedures across multiple nodes.

Network Preparation:

Ensure iDRAC interfaces are properly connected to the management network.

Verify network settings to allow access from the engineer’s workstation.

Dell PowerScale

Reference: Dell EMC PowerScale OneFS Installation Guide:

Provides detailed steps on installing OneFS using iDRAC.

Dell EMC PowerScale Networking Guide:

Discusses management network configurations, including iDRAC setup.

Dell EMC iDRAC User’s Guide:

Offers comprehensive information on using iDRAC features.

Knowledge Base Articles:

Article ID 000125678: "Initial Cluster Configuration Using iDRAC"

Article ID 000125679: "Best Practices for Remote Installation on PowerScale Nodes"

Question #40

An engineer wants to create a 4-node cluster after rack and stack.

What port must they use to start the installation?

A . COM
B . FE
C . BE
D . iDRAC

Reveal Solution Hide Solution

Correct Answer: D
D

Explanation:

When an engineer wants to create a 4-node cluster after rack and stack, they must use the iDRAC (Integrated Dell Remote Access Controller) port to start the installation.

Understanding iDRAC:

Remote Management:

iDRAC provides out-of-band management capabilities, allowing administrators to manage and

monitor nodes remotely.

Virtual Console Access:

Offers a virtual console for accessing the node’s BIOS and performing installations.

Initial Cluster Setup with iDRAC:

Accessing the Node:

Connect to each node’s iDRAC interface using its IP address.

Starting the Installation:

Use the iDRAC virtual console to interact with the node as if you were physically present.

Benefits:

No need for physical access to the COM port or direct console connections.

Allows for remote configuration and reduces the time required for setup.

Why iDRAC is Used Over Other Ports:

COM Port:

The COM (serial) port can be used for initial setup, but it requires physical access and serial cables.

Less convenient compared to iDRAC’s remote capabilities.

FE (Front-End) and BE (Back-End) Ports:

FE and BE ports are used for data network connections, not for initial setup or management.

The initial configuration cannot be performed through these ports.

Procedure for Using iDRAC:

Step 1: Connect to iDRAC

Ensure that iDRAC network interfaces are connected and configured with IP addresses.

Access iDRAC via a web browser using the IP address.

Step 2: Launch Virtual Console

Log in to the iDRAC interface.

Launch the virtual console to access the node’s system interface.

Step 3: Perform Initial Configuration

Use the virtual console to run the OneFS installation wizard. Configure cluster settings, networking, and other parameters. Dell PowerScale Best Practices: Using iDRAC for Installation:

Recommended for its convenience and efficiency.

Allows for consistent setup procedures across multiple nodes.

Network Preparation:

Ensure iDRAC interfaces are properly connected to the management network.

Verify network settings to allow access from the engineer’s workstation.

Dell PowerScale

Reference: Dell EMC PowerScale OneFS Installation Guide:

Provides detailed steps on installing OneFS using iDRAC.

Dell EMC PowerScale Networking Guide:

Discusses management network configurations, including iDRAC setup.

Dell EMC iDRAC User’s Guide:

Offers comprehensive information on using iDRAC features.

Knowledge Base Articles:

Article ID 000125678: "Initial Cluster Configuration Using iDRAC"

Article ID 000125679: "Best Practices for Remote Installation on PowerScale Nodes"

Question #40

An engineer wants to create a 4-node cluster after rack and stack.

What port must they use to start the installation?

A . COM
B . FE
C . BE
D . iDRAC

Reveal Solution Hide Solution

Correct Answer: D
D

Explanation:

When an engineer wants to create a 4-node cluster after rack and stack, they must use the iDRAC (Integrated Dell Remote Access Controller) port to start the installation.

Understanding iDRAC:

Remote Management:

iDRAC provides out-of-band management capabilities, allowing administrators to manage and

monitor nodes remotely.

Virtual Console Access:

Offers a virtual console for accessing the node’s BIOS and performing installations.

Initial Cluster Setup with iDRAC:

Accessing the Node:

Connect to each node’s iDRAC interface using its IP address.

Starting the Installation:

Use the iDRAC virtual console to interact with the node as if you were physically present.

Benefits:

No need for physical access to the COM port or direct console connections.

Allows for remote configuration and reduces the time required for setup.

Why iDRAC is Used Over Other Ports:

COM Port:

The COM (serial) port can be used for initial setup, but it requires physical access and serial cables.

Less convenient compared to iDRAC’s remote capabilities.

FE (Front-End) and BE (Back-End) Ports:

FE and BE ports are used for data network connections, not for initial setup or management.

The initial configuration cannot be performed through these ports.

Procedure for Using iDRAC:

Step 1: Connect to iDRAC

Ensure that iDRAC network interfaces are connected and configured with IP addresses.

Access iDRAC via a web browser using the IP address.

Step 2: Launch Virtual Console

Log in to the iDRAC interface.

Launch the virtual console to access the node’s system interface.

Step 3: Perform Initial Configuration

Use the virtual console to run the OneFS installation wizard. Configure cluster settings, networking, and other parameters. Dell PowerScale Best Practices: Using iDRAC for Installation:

Recommended for its convenience and efficiency.

Allows for consistent setup procedures across multiple nodes.

Network Preparation:

Ensure iDRAC interfaces are properly connected to the management network.

Verify network settings to allow access from the engineer’s workstation.

Dell PowerScale

Reference: Dell EMC PowerScale OneFS Installation Guide:

Provides detailed steps on installing OneFS using iDRAC.

Dell EMC PowerScale Networking Guide:

Discusses management network configurations, including iDRAC setup.

Dell EMC iDRAC User’s Guide:

Offers comprehensive information on using iDRAC features.

Knowledge Base Articles:

Article ID 000125678: "Initial Cluster Configuration Using iDRAC"

Article ID 000125679: "Best Practices for Remote Installation on PowerScale Nodes"

Question #40

An engineer wants to create a 4-node cluster after rack and stack.

What port must they use to start the installation?

A . COM
B . FE
C . BE
D . iDRAC

Reveal Solution Hide Solution

Correct Answer: D
D

Explanation:

When an engineer wants to create a 4-node cluster after rack and stack, they must use the iDRAC (Integrated Dell Remote Access Controller) port to start the installation.

Understanding iDRAC:

Remote Management:

iDRAC provides out-of-band management capabilities, allowing administrators to manage and

monitor nodes remotely.

Virtual Console Access:

Offers a virtual console for accessing the node’s BIOS and performing installations.

Initial Cluster Setup with iDRAC:

Accessing the Node:

Connect to each node’s iDRAC interface using its IP address.

Starting the Installation:

Use the iDRAC virtual console to interact with the node as if you were physically present.

Benefits:

No need for physical access to the COM port or direct console connections.

Allows for remote configuration and reduces the time required for setup.

Why iDRAC is Used Over Other Ports:

COM Port:

The COM (serial) port can be used for initial setup, but it requires physical access and serial cables.

Less convenient compared to iDRAC’s remote capabilities.

FE (Front-End) and BE (Back-End) Ports:

FE and BE ports are used for data network connections, not for initial setup or management.

The initial configuration cannot be performed through these ports.

Procedure for Using iDRAC:

Step 1: Connect to iDRAC

Ensure that iDRAC network interfaces are connected and configured with IP addresses.

Access iDRAC via a web browser using the IP address.

Step 2: Launch Virtual Console

Log in to the iDRAC interface.

Launch the virtual console to access the node’s system interface.

Step 3: Perform Initial Configuration

Use the virtual console to run the OneFS installation wizard. Configure cluster settings, networking, and other parameters. Dell PowerScale Best Practices: Using iDRAC for Installation:

Recommended for its convenience and efficiency.

Allows for consistent setup procedures across multiple nodes.

Network Preparation:

Ensure iDRAC interfaces are properly connected to the management network.

Verify network settings to allow access from the engineer’s workstation.

Dell PowerScale

Reference: Dell EMC PowerScale OneFS Installation Guide:

Provides detailed steps on installing OneFS using iDRAC.

Dell EMC PowerScale Networking Guide:

Discusses management network configurations, including iDRAC setup.

Dell EMC iDRAC User’s Guide:

Offers comprehensive information on using iDRAC features.

Knowledge Base Articles:

Article ID 000125678: "Initial Cluster Configuration Using iDRAC"

Article ID 000125679: "Best Practices for Remote Installation on PowerScale Nodes"

Question #40

An engineer wants to create a 4-node cluster after rack and stack.

What port must they use to start the installation?

A . COM
B . FE
C . BE
D . iDRAC

Reveal Solution Hide Solution

Correct Answer: D
D

Explanation:

When an engineer wants to create a 4-node cluster after rack and stack, they must use the iDRAC (Integrated Dell Remote Access Controller) port to start the installation.

Understanding iDRAC:

Remote Management:

iDRAC provides out-of-band management capabilities, allowing administrators to manage and

monitor nodes remotely.

Virtual Console Access:

Offers a virtual console for accessing the node’s BIOS and performing installations.

Initial Cluster Setup with iDRAC:

Accessing the Node:

Connect to each node’s iDRAC interface using its IP address.

Starting the Installation:

Use the iDRAC virtual console to interact with the node as if you were physically present.

Benefits:

No need for physical access to the COM port or direct console connections.

Allows for remote configuration and reduces the time required for setup.

Why iDRAC is Used Over Other Ports:

COM Port:

The COM (serial) port can be used for initial setup, but it requires physical access and serial cables.

Less convenient compared to iDRAC’s remote capabilities.

FE (Front-End) and BE (Back-End) Ports:

FE and BE ports are used for data network connections, not for initial setup or management.

The initial configuration cannot be performed through these ports.

Procedure for Using iDRAC:

Step 1: Connect to iDRAC

Ensure that iDRAC network interfaces are connected and configured with IP addresses.

Access iDRAC via a web browser using the IP address.

Step 2: Launch Virtual Console

Log in to the iDRAC interface.

Launch the virtual console to access the node’s system interface.

Step 3: Perform Initial Configuration

Use the virtual console to run the OneFS installation wizard. Configure cluster settings, networking, and other parameters. Dell PowerScale Best Practices: Using iDRAC for Installation:

Recommended for its convenience and efficiency.

Allows for consistent setup procedures across multiple nodes.

Network Preparation:

Ensure iDRAC interfaces are properly connected to the management network.

Verify network settings to allow access from the engineer’s workstation.

Dell PowerScale

Reference: Dell EMC PowerScale OneFS Installation Guide:

Provides detailed steps on installing OneFS using iDRAC.

Dell EMC PowerScale Networking Guide:

Discusses management network configurations, including iDRAC setup.

Dell EMC iDRAC User’s Guide:

Offers comprehensive information on using iDRAC features.

Knowledge Base Articles:

Article ID 000125678: "Initial Cluster Configuration Using iDRAC"

Article ID 000125679: "Best Practices for Remote Installation on PowerScale Nodes"

Question #17

R2 devices

Reveal Solution Hide Solution

Question #18

When transitioning from Adaptive Copy mode to SRDF/A mode, what is the minimum number of cycle switches required to reach data consistency?

A . 1
B . 2
C . 4
D . 8

Reveal Solution Hide Solution

Question #19

In PowerMax VMAX All Flash and VMAX3 which thin provisioning component can be changed with SYMCLI or Unisphere?

A . Storage Resource Pool
B . Disk Group
C . Storage Group
D . Virtual Provisioning Pool

Reveal Solution Hide Solution

Question #20

You are in a meeting with a customer to discuss virtual provisioning on VMAX3 arrays. The customer wants information on extent allocation during thin device creation.

How many extent(s) are allocated when a thin device is created?

A . 0
B . 1
C . 12
D . 42

Reveal Solution Hide Solution