DELL EMC D-PE-OE-23 Dell Technologies PowerEdge Operate 2023 Online Training
DELL EMC D-PE-OE-23 Online Training
The questions for D-PE-OE-23 were last updated at Nov 23,2024.
- Exam Code: D-PE-OE-23
- Exam Name: Dell Technologies PowerEdge Operate 2023
- Certification Provider: DELL EMC
- Latest update: Nov 23,2024
Assign a new password
A technician is sent on-site to troubleshoot a server that halts during POST. The iDRAC System Event Log shows the following errors: A bus fatal error was detected on a component at bus 0 device 1 function 1 A bus fatal error was detected on a component at bus 1 device 0 function 0 CPU 1 has an internal error (IERR)
The following system information is provided.
Which system component is the most likely cause?
- A . Processor
- B . Network daughter card
- C . RAID controller
- D . System board
A system administrator plans to use a remote desktop that has the DRAC tools installed to run RACADM commands.
Which two CLI options must be in the RACADM command? (Select 2)
- A . Login credentials
- B . Certificate
- C . IP address of iDRAC
- D . Host OS credentials
Which tool allows an administrator to remotely back up a PowerEdge server configuration to streamline server deployments?
- A . OME
- B . OMSA
- C . iDRAC
- D . Virtual console
Which three steps must a technician take prior to replacing a server component with blue tabs/release? (Choose three.)
- A . Powers off the server
- B . Apply anti-static procedures
- C . Hot-swap the component
- D . Put the server into maintenance mode
- E . Remove power cables
How can a technician know whether IDRAC9 System Lockdown mode is enabled?
- A . Lockdown activation message in red box in the iDRAC web GUI Access to LCC is disabled when the server boots
- B . Lockdown activation message in yellow box in the iDRAC web GUI Access to LCC is disabled when the server boots
- C . Lockdown activation message in red box in the iDRAC web GUI Access to LCC requires a password when the server boots
- D . Lockdown activation message in yellow box in the iDRAC web GUI Access to LCC requires a password when the server boots
Which application reduces the manual effort to update 500 Dell EMC PowerEdge R750 servers?
- A . iDRAC9
- B . Lifecycle Controller
- C . OpenManage Enterprise
- D . OpenManage Server Administrator
An error occurs during data transmission between the CPU and DIMM.
Which feature in a Dell PowerEdge 16G server is responsible for fixing correctable memory errors?
- A . Memory Retraining
- B . Persistent Memory
- C . Post Package Repair
- D . Memory Health Check
What is the minimum version of ESXi that should be used to avoid potential issues writing to the SD cards when running ESXi 7 from an IDSDM?
- A . 7.0 U2e
- B . 7.0 U2c
- C . 7.0 U3g
- D . 7.0 U3c
A technician needs to connect a server to a network but the network switch has only two available network ports so only two network cables can be connected. The user needs as much bandwidth as possible for their workload so the two network cables need to connect to LOM1 and LOM2.
At some point in the future a new network switch will enable additional cables to be used. The technician wants to satisfy the user requirements yet still be able to access the iDRAC without having to reconfigure the iDRAC once new cables are installed in the iDRAC Dedicated NIC.
What is the best way to configure the iDRAC?
- A . Use a splitter cable in one of the network switch ports to connect the same cable to both LOM1 and the iDRAC dedicated NIC
- B . Use a splitter cable in one of the network switch ports to connect the same cable to both LOM1 and LOM2 with the second network cable connecting to the iDRAC dedicated NIC
- C . Set up a dedicated NIC with LOM1 as the NIC selection
- D . Set up a shared NIC with LOM1 as the NIC selection with Auto Dedicated NIC selected
Latest D-PE-OE-23 Dumps Valid Version with 270 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
