DELL EMC D-PDC-DY-23 Dell PowerSwitch Data Center Deploy 2023 Online Training
DELL EMC D-PDC-DY-23 Online Training
The questions for D-PDC-DY-23 were last updated at Nov 23,2024.
- Exam Code: D-PDC-DY-23
- Exam Name: Dell PowerSwitch Data Center Deploy 2023
- Certification Provider: DELL EMC
- Latest update: Nov 23,2024
With what feature is the downstream ethernet 1/1/9:1-1/1/9:4 command associated?
- A . Downlink Failure Detection
- B . Uplink Failure Detection
- C . Unidirectional Forwarding Detection
- D . Bidirectional Forwarding Detection
What is the size of the VLAN tag in an Ethernet frame?
- A . 4 bytes
- B . 8 bytes
- C . 1 byte
- D . 2 bytes
Which two commands display if a port is currently active in a VLAN?
- A . "show interface vlan" and "show interfaces status"
- B . "show interface vlan" and "show startup-configuration"
- C . "show startup-configuration" and "show vlan"
- D . "show vlan" and "show interfaces status"
Refer to the exhibit:
What happens when a network administrator enters the shutdown command?
- A . Terminates established BGP sessions for the specified ASN (64567).
- B . Maintains existing BGP sessions but no longer establishes new ones.
- C . Stops any traffic from being sent on the physical interface that is used to reach neighbor 192.168.200.1.
- D . Terminates any established BGP sessions for the specified neighbor.
Which LSA type contains information about routes redistributed into OSPF?
- A . 3
- B . 10
- C . 5
- D . 8
What are the benefits associated with a multiple-area OSPF implementation?
- A . Lower costs by replacing traditional routers with distribution layer switches.
- B . Lack of summarization between areas allow specific routes in the routing table.
- C . All routes are easy to find since routing table entries are larger.
- D . Each router has a more manageable LSDB.
A network administrator must configure a virtual IP address using VRRP on interface VLAN 100 within OS10.
What are the correct steps to accomplish this?
- A . OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.1/24
OS10(conf-if-vl-100)# standby-group 256
OS10(conf-vlan100-vrid-256)# standby-address 10.0.100.2 - B . OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.2/24
OS10(conf-if-vl-100)# standby-group 250
OS10(conf-vlan100-vrid-250)# virtual-address 10.0.100.1 - C . OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.2/24
OS10(conf-if-vl-100)# vrrp-group 256
OS10(conf-vlan100-vrid-256)# virtual-address 10.0.100.1 - D . OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.1/24
OS10(conf-if-vl-100)# vrrp-group 250
OS10(conf-vlan100-vrid-250)# virtual-address 10.0.100.2
Which multicast address do all OSPF routers use?
- A . 224.0.0.6
- B . 239.0.0.6
- C . 239.0.0.4
- D . 224.0.0.5
In a PIM Sparse Mode based multicast topology, what role does the Rendezvous Point provide?
- A . The node is used to provide (S,G) across a Layer 3 boundary.
- B . The location PIM sends traffic before invoking SPT.
- C . The node is used to provide (*,G) on a Layer 2 shared segment.
- D . The first-hop router is used to provide routing between the source and receiver.
Latest D-PDC-DY-23 Dumps Valid Version with 155 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
