DELL EMC D-PDC-DY-23 Dell PowerSwitch Data Center Deploy 2023 Online Training
DELL EMC D-PDC-DY-23 Online Training
The questions for D-PDC-DY-23 were last updated at Nov 23,2024.
- Exam Code: D-PDC-DY-23
- Exam Name: Dell PowerSwitch Data Center Deploy 2023
- Certification Provider: DELL EMC
- Latest update: Nov 23,2024
Two (2) Dell EMC Networking OS10 switches in a VLT configuration need to be upgraded.
How will the reload of these switches proceed to result in the default initial state?
- A . Reload the primary VLT node. This process will automatically trigger the reload of the secondary node after it has completely recovered.
- B . Reload the primary VLT node and wait for it to join as secondary. Wait until after delay restore timer has expired. Reload VLT secondary node and wait for it to join as secondary.
- C . Reload the primary VLT node.This will automatically trigger the simultaneous reload of the secondary node.
- D . Reload the primary VLT node and wait for it to join as primary. Wait until after delay restore timer has expired. Reload VLT secondary node and wait for it to join as secondary.
What is the default transmission interval of an LLDPDU in SmartFabric OS10?
- A . 2
- B . 10
- C . 20
- D . 30
Which multicast address is used by all OSPF routers?
- A . 239.0.0.4
- B . 239.0.0.6
- C . 224.0.0.5
- D . 224.0.0.6
When configuring a vrf instance for the management interface that has been in use, what step must be done first to configure it?
- A . Configure a management route
- B . Remove the default route
- C . Remove all configured settings
- D . Configure an IP Address
Refer to the exhibit.
Where is the rendezvous point for the group 239.255.255.250?
- A . 10.0.13.1
- B . 10.0.14.1
- C . eth1/1/54
- D . vlan300
What does an ABR do with a Type 7 LSA it receives from an attached NSSA?
- A . It translates the Type 7 to a Type 5, and floods the LSA
- B . Nothing, since Type 7 originated external routing information is rejected by an ABR
- C . It floods the Type 7 to the rest of the OSPF domain
- D . It summarizes the information in the Type 7 LSA in a new Type 3 LSA
Which IEEE standard defines the Multiple Spanning Tree Protocol?
- A . 802.1s
- B . 802.1w
- C . 802.1d
- D . 802.1ad
A network administrator wants to configure a timing protocol with these requirements:
– Hardware time stamping to achieve sub microsecond synchronization.
– Master IP address: 192.168.1.100.
– Use interface Ethernet 1/1/1 to enable timing protocol.
Which configuration supports the requirements?
- A . OS10(config)# ptp clock boundary
OS10(config)# ptp domain 1
OS10(config)# ptp system time enable
OS10(config-if-eth1/1/1)# ptp enable
OS10(config-if-eth1/1/1)# ptp role slave
OS10(config-if-eth1/1/1)# ptp transport ipv4 unicast slave
OS10(config-if-eth1/1/1-ptp-ipv4-slave)# master 192.168.1.100 - B . OS10(config-if-eth1/1/1)# ntp authenticate
OS10(config-if-eth1/1/1)# ntp trusted-key 345
OS10(config-if-eth1/1/1)# ntp authentication-key 345 md5 0 5A60910FED211F02
OS10(config-if-eth1/1/1)# ntp server 192.168.1.100 key 345
OS10(config-if-eth1/1/1)# ntp master 7 - C . OS10(config)# ntp authenticate
OS10(config)# ntp trusted-key 345
OS10(co345 md5 0 5A60910FED211F02
OS10(config)# ntp server 192.168.1.100 key 345
OS10(config-if-eth1/1/1)# nfig)# ntp authentication-key ntp master 7 - D . OS10(config)# ptp clock boundary
OS10(config)# ptp domain 1
OS10(config)# ptp system time enable
OS10(config)# ptp enable
OS10(config)# ptp role master
OS10(config)# ptp transport ipv4 unicast slave
OS10(config-if-eth1/1/1)# master 192.168.1.100
When using Policy-Based Routing, what is a valid action?
- A . Set source IP address
- B . Drop packet
- C . Set destination TCP port number
- D . Set 802.1Q VLAN ID
What type of network in a Data Center flattens the core and aggregation layers into a single tier?
- A . Leaf
- B . Leaf-spine
- C . Spine
- D . TRILL
Latest D-PDC-DY-23 Dumps Valid Version with 155 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
