DELL EMC D-PCM-DY-23 Dell PowerSwitch Campus Deploy 2023 Online Training
DELL EMC D-PCM-DY-23 Online Training
The questions for D-PCM-DY-23 were last updated at Nov 26,2024.
- Exam Code: D-PCM-DY-23
- Exam Name: Dell PowerSwitch Campus Deploy 2023
- Certification Provider: DELL EMC
- Latest update: Nov 26,2024
What are key features of the Dell EMC N4064 or N4064F switches?
- A . Up to 640 Gbps switch fabric capacity and hot swap expansion module support for dual QSFP+ (8 x 10GbE)
- B . Up to 1.0 Tbps switch fabric capacity and up to 48-line rate 10GbE ports per switch
- C . Up to 1.2 Tbps switch fabric capacity and up to 64-line rate 10GbE ports per switch
- D . Up to 48-line rate 10GbE ports per switch and hot swap expansion module support for dual QSFP+ (8 x 10GbE)
Which port security method converts existing dynamically learned MAC addresses on an interface to this mode and not age out?
- A . Static
- B . MAC address
- C . Sticky
- D . Dynamic
What is true about Dell N1100 Series switches?
- A . They contain 6x 100 Gig interfaces.
- B . They are Open Networking switches.
- C . They accept static routes.
- D . They are suitable for core layer deployment.
Which two are true about discovery protocols on the Dell N-Series Voice VLAN feature? (Select 2)
- A . A Cisco phone can be configured by CDP
- B . Only used ISDP
- C . Uses both LLDP and ISDP
- D . Only uses LLDP
- E . A Cisco phone can only be discovered by CDP
What describes one of the primary functions of a VLAN?
- A . Separate switchport interfaces
- B . Separate the broadcast domain
- C . Join networks together
- D . Route to the Internet
Which Layer 3 protocol does MLAG support?
- A . None
- B . Static Routing
- C . OSPFD.
- D . RIPv2
Which command configures OSPF to advertise the network 10.10.0.0/16 to the Backbone Area?
- A . network 10.10.0.0 0.0.255.255 area 1
- B . network 10.10.0.0 255.255.0.0 area 0
- C . network 10.10.0.0 0.0.255.255 area 0
- D . network 10.10.0.0 255.255.0.0 area 1
Which Layer 2 network protocol is used for automatic configuration of switch VLANs and dynamically manages VLAN membership on trunk ports?
- A . MSTP
- B . PVST
- C . RSTP
- D . GVRP
When setting up VoIP, you decide that you want to use LLDP. LLDP is enabled by default and LLDP Transmit Management Information and Notification modes are enabled.
What additional steps need to be performed?
- A . Enable ISDP and enable LLDP-MED confignotification
- B . Disable ISDP and enable LLDP-MED confignotification
- C . Enable ISDP and disable LLDP-MED confignotification
- D . Disable ISDP and disable LLDP-MED confignotification
What is the PoE source maximum power budget for a Class 3 end device?
- A . 12.95 watts
- B . 60 watts
- C . 30 watts
- D . 15.4 watts
Latest D-PCM-DY-23 Dumps Valid Version with 170 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
